Advertisement
4-1. Setup Menu (BVP-500 series)
4-1-2. Paint Menu
Page
Ver.
Item
Detail 2
Detail
H/V Ratio
Frequency
MIX Ratio
W.Limitter
B.Limitter
Comb
Knee APT.
Knee APT.
Test
Clear
Skin Detail
Master SW
SkinDTL
Level
Phase
Width
Sat
Gate
Gate Vf
Auto Hue
Clear
4-8 (E)
Settings
Contents
[On], Off
Turns the function on and off to improve resolution by adding detail signal.
_99 to 99 ([0])
Adjusts the mix ratio of H and V detail signal.
_99 to 99 ([0])
Adjusts the boost frequency for H detail signal.
_99 to 99 ([0])
Adjusts the mix ratio of H detail signal used before and after the gamma
compensation circuit.
_99 to 99 ([0])
Adjust the clipping level adainst the higher detail signal at the maximum level.
_99 to 99 ([0])
Adjusts the clippping level against the lower detail signal at the minimum level.
_99 to 99 ([0])
Sets the effect volume of the comb filter
99 (Causes less cross colors.) ↔ _99 (Yields clear pictures, but causes
more cross colors.)
* For a PAL model, this function has the effect on not every object but a
specified object.
On, [Off]
Turns the knee aperture function on and off
_99 to 99 ([0])
Adjusts the detail level for signals which exceeds the knee point to
emphasize the detail of the highlight
1, 2, [Off]
Selects the test signal.
1
: Outputs the sawtooth waveform test signal
2
: Outputs 3-step waveform test signal
Off
: No test signal is output
Throw MENU SELECT
Sets all settings on the Detail 2 page to 0.
switch to ENTER
(When you throw MENU SELECT switch to ENTER, the "Clear"
to execute
indication flashes. Throw MENU SELECT switch to ENTER again to
execute; throw to CANCEL to cancel.)
On, [Off]
Turns the skin tone detail function on and off
n When set to ON, the setting of SkinDTL for No.1 shown below is always On
1 : On
Turns the skin tone detail function on and off for each selection 1 to 3 of
2 : On, [Off]
Gate item.
3 : On, [Off]
1 : _99 to 99 ([0])
Adjusts the skin tone detail for each selection 1 to 3 of Gate item.
2 : _99 to 99 ([0])
3 : _99 to 99 ([0])
1 : 0 to 359 ([120])
Sets the color phase that is the center of the color area where the skin
2 : 0 to 359 ([120])
tone detail function is to be activated for each selection 1 to 3 of Gate
3 : 0 to 359 ([120])
item.
1 : 0 to 90 ([0])
Sets the width of the color area around the phase where the skin tone
2 : 0 to 90 ([0])
detail function is to be activated for each selection 1 to 3 of Gate item.
3 : 0 to 90 ([0])
1 : _99 to 99 ([0])
Sets the saturation for which the skin tone detail function is to be
2 : _99 to 99 ([0])
activated for each selection 1 to 3 of Gate item.
3 : _99 to 99 ([0])
[1], 2, 3, irs
1, 2, 3 : Selects the gate marker showing the area where the skin tone
irs :
On, [Off]
Turns on and off the gate marker indication selected by the above
Gate item
Throw MENU SELECT
Sets the skin tone detail hue function automatically
switch to ENTER
to execute.
Throw MENU SELECT
Sets all settings on the Skin Detail page to 0.
switch to ENTER
(When you throw MENU SELECT switch to ENTER, the "Clear"
to execute.
indication flashes. Throw MENU SELECT switch to ENTER again to
execute; throw to CANCEL to cancel.)
detail function is activated
Indicates the auto-iris detection area when the unit is put into the "Skn"
mode by using the Operation menu, Auto Iris/Knee page
BKP-5090
Advertisement
