Advertisement
Location of controls
Remote Control
TONE
(CFD-S32/S32L only)
(CFD-S32/S32L only)
TAPE
Tape compartment
CD compartment
RADIO BAND
SLEEP
CD
AUTO PRESET
OPR/BATT
PLAY MODE
indicator
MONO/ST*
Z PUSH OPEN/CLOSE
FUNCTION
Number buttons
MODE*
BAND
TUNE +, –
X
N
LOOP
FLASH
TUNING –, +
., >
MEGA BASS
OPERATE
SLEEP
(or POWER)
x
DISPLAY ENT
i (headphones) jack
u
MEMORY
Number buttons for
* MODE on the remote has the same function
VOLUME +,–
as PLAY MODE•MONO/ST on the player.
CD/RADIO DIRECT OPERATION
* The name of this button is PLAY MODE•MONO/ST for CFD-S22/S32,
PLAY MODE•MONO/ST ISS for CFD-S22L/S32L/922L.
Tip
To listen through headphones, connect the headphones to the
i (headphones) jack.
Adjusting the sound emphasis (MEGA BASS/TONE)
Reinforcing the bass sound
Press MEGA BASS.
"MEGA BASS" appears in the display.
To return to normal sound, press the button again.
Adjusting the tone (CFD-S32/S32L only)
Press TONE.
To enhance
Display
the high tone
HI
the low tone
LO
Playing a CD
Using the display
1
Press CD (direct power-on).
Checking the total track number and playing time
Press DISPLAY ENT•MEMORY in stop mode.
Total track number
Total playing time
Checking the remaining time
OPERATE
Press DISPLAY ENT•MEMORY while playing a CD.
(or POWER)
2
Press Z PUSH OPEN/CLOSE down to open the CD
To display
compartment and place a CD in the CD compartment.
the current track number and
the remaining time on the current track*
the number of tracks left
and remaining time on the CD
VOL +,–
c
the current track number
and playing time
x
* For a track whose number is more than 20, the remaining time appears as
"- -:- -" in the display.
., >
MEGA BASS
With the labeled side up
Locating a specific track
TONE
To locate
3
a specific track directly
Close the CD compartment.
a point while listening
to the sound
a point while observing
the display
c
Tip
When you locate a track numbered over 10, press >10 first, then the
corresponding number buttons.
Example:To play track number 23, press >10 first, then 2 and 3.
Note
4
You cannot locate a specific track if "SHUF" or "PGM" is lit in the display.
Press u (N on the remote, CFD-S32/S32L only).
Turn off the indication by pressing x.
The player plays all the tracks once.
Display
Repeat Play
1
Press CD.
2
Track number Playing time
Proceed as follows:
To repeat
a single track
To
Press
adjust the volume
VOLUME +, – (VOL +, – on the remote,
CFD-S32/S32L only)
stop playback
x
all the tracks
pause playback
u (X on the remote, CFD-S32/S32L only)
Press the button again to resume play after
pause.
tracks in random order
go to the next track
>
go back to the previous track
.
remove the CD
Z PUSH OPEN/CLOSE
programmed tracks
turn on/off the player
OPERATE (or POWER)
To cancel Repeat Play
Press PLAY MODE•MONO/ST until "REP" disappears from the display.
Shuffle Play
1
Press CD.
2
Press PLAY MODE•MONO/ST until "SHUF" appears in the
display.
3
Press u to start shuffle play.
To cancel Shuffle Play
Press PLAY MODE•MONO/ST until "SHUF" disappears from the display.
Press DISPLAY ENT•MEMORY
once
Programme Play
twice
1
Press CD.
three times
2
Press PLAY MODE•MONO/ST until "PGM" appears in the
display.
3
Press the number buttons for the tracks you want to
programme in the order you want. You can arrange the playing
order of up to 20 tracks.
Press
Display
a number button of the track.
> (forward) or . (backward) while
Programmed track
playing until you find the point.
> (forward) or . (backward) in
Playing order
pause until you find the point.
4
Press u to start program play.
To cancel Programme Play
Press PLAY MODE•MONO/ST until "PGM" disappears from the display.
To check the order of tracks before play
Press DISPLAY ENT•MEMORY.
Every time you press the button, the track number appears in the
programed order.
To change the current programme
Press x once if the CD is stopped and twice if the CD is playing. The
current program will be erased. Then create a new programme following
the programming procedure.
Do this
Tips
1 Press PLAY MODE•MONO/ST until
• You can play the same program again, since the program is saved until
"REP 1" appears.
you open the CD compartment.
2 Press the number button for the track
• You can record your own program. After you've created the programme,
you want to repeat.
insert a blank tape and press z to start recording.
1 Press PLAY MODE•MONO/ST until
"REP ALL" appears.
2 Press u.
1 Press PLAY MODE•MONO/ST until
"SHUF REP" appears.
2 Press u.
1 Press PLAY MODE•MONO/ST until
"PGM REP" appears.
2 Press the number buttons for the tracks
you want to programme in the order you
want up to 20 tracks.
3 Press u.
Listening to the radio
Enjoying Sound effects (LOOP/FLASH)
1
Press RADIO BAND•AUTO PRESET until the band you
(CFD-S32/S32L only)
want appears in the display (direct power-on).
You can repeat part of a CD (LOOP) and can "flash" the CD sound (FLASH)
Each time you press the button, the indication changes as
during playback.
follows:
1
CFD-S22/S32: "FM1" n "FM2" n "AM"
Play a CD.
CFD-S22L/S32L/922L: "FM1" n "FM2" n "MW" n
"LW".
2
Press and hold LOOP or FLASH at the point you want to
start the function.
Display
To
Press and Hold
repeat a selected part of a CD
LOOP on the remote
"flash" the CD sound
FLASH on the remote
To cancel the LOOP or FLASH function
Release the button.
2
The player returns to normal play.
Hold down TUNING + or – (TUNE + or – on the remote,
CFD-S32/S32L only) until the frequency digits begin to
change in the display.
Notes on CDs
• Before playing, clean the CD with a cleaning cloth. Wipe the CD from the
center out.
Display
The player automatically scans the radio frequencies and
stops when it finds a clear station.
• Do not use solvents such as benzine, thinner, commercially available
If you can't tune in a station, press the button repeatedly
cleaners or anti-static spray intended for vinyl LPs.
to change the frequency step by step.
• Do not expose the CD to direct sunlight or heat sources such as hot air
ducts, nor leave it in a car parked in direct sunlight as there can be a
considerable rise in temperature inside the car.
• Do not stick paper or sticker on the CD, nor scratch the surface of the CD.
To
Press
• After playing, store the CD in its case.
adjust the volume
VOLUME +, – (VOL +, – on the remote,
If there is a scratch, dirt or fingerprints on the CD, it may cause tracking
CFD-S32/S32L only)
error.
turn on/off the radio
OPERATE (or POWER)
To improve broadcast reception
Reorient the antenna for FM. Reorient the player itself for AM or
MW/LW.
FM
Tips
• The "FM1" and "FM2" bands have the same functions. You can store the
stations you want separately in "FM1" and "FM2".
• If the FM broadcast is noisy, press PLAY MODE•MONO/ST until
"Mono" appears in the display and the radio will play in monaural.
Presetting radio stations
You can store radio stations into the player's memory. You can preset up
to 30 radio stations (CFD-S22/S32) or 40 radio stations (CFD-S22L/S32L/
922L), 10 for each band in any order.
1
Press RADIO BAND•AUTO PRESET to select the band.
Display
2
Hold down RADIO BAND•AUTO PRESET for 2 seconds
until "AUTO" flashes in the display.
Display
3
Press DISPLAY ENT•MEMORY.
The stations are stored in memory from the lower frequencies
to the higher ones.
Tip
If you automatically preset the "FM1" or "FM2" band, 10 radio stations
are stored in "FM1" band and 10 more radio stations are stored in
"FM2" band.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Tune in a station you want.
3
Hold down the number buttons that you want to preset the new station
on for about 2 seconds.
Display
CD/RADIO DIRECT OPERATION
AM/MW/LW
The new station replaces the old one.
Playing preset radio stations
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Press the number buttons to tune in the stored station.
CD/RADIO DIRECT OPERATION
Advertisement
