Sony RDP-XF300iP Operating Instructions

Personal Audio
Docking System
©2012 Sony Corporation Printed in China
RDP-XF300iP
 Because Bluetooth devices and wireless LAN
WARNING
(IEEE802.11b/g/n) use the same frequency, microwave
interference may occur and resulting in communication
speed deterioration, noise, or invalid connection if this
To reduce the risk of fire or electric shock, do
unit is used near a wireless LAN device. In such a case,
not expose this apparatus to rain or moisture.
perform the following.
— Use this unit at least 10 m away from any wireless LAN
To reduce the risk of fire, do not cover the ventilation of the
device.
apparatus with newspapers, tablecloths, curtains, etc. And
do not place lighted candles on the apparatus. — If this unit is used within 10 m of a wireless LAN
device, turn off the wireless LAN device.
To reduce the risk of fire or electric shock, do not expose
— Install this unit and iPod as near to each other as
this apparatus to dripping or splashing, and do not place
possible.
objects filled with liquids, such as vases, on the apparatus.
 Microwaves emitting from a Bluetooth device may affect
Do not install the appliance in a confined space, such as a
the operation of electronic medical devices. Turn off this
bookcase or built-in cabinet.
unit and iPod in the following locations, as it may cause
an accident.
Do not expose the batteries (battery pack or batteries
installed) to excessive heat such as sunshine, fire or the like
— where inflammable gas is present, in a hospital, train,
for a long time. airplane, or a gasoline station
— near automatic doors or a fire alarm
As the main plug is used to disconnect the unit from the
 This unit supports security capabilities that comply with
mains, connect the unit to an easily accessible AC outlet.
the Bluetooth standard to provide a secure connection
Should you notice an abnormality in the unit, disconnect
when the Bluetooth wireless technology is used, but
the main plug from the AC outlet immediately.
security may be insufficient, depending on the setting. Be
The unit is not disconnected from the AC power source
careful when communicating using Bluetooth wireless
(mains) as long as it is connected to the wall outlet, even if
technology.
the unit itself has been turned off.
 We do not take any responsibility for leakage of
information during Bluetooth communication.
The nameplate and important information concerning
safety are located on the bottom exterior of the main unit  Connection with all Bluetooth devices cannot be
and on the surface of the AC adaptor. guaranteed.
— A device featuring Bluetooth function is required to
CAUTION conform to the Bluetooth standard specified by
Bluetooth SIG, Inc. and be authenticated.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same type.
— Even if the connected device conforms to the above
mentioned Bluetooth standard, some devices may not
Disposal of Old Electrical & Electronic
be connected or work correctly, depending on the
Equipment (Applicable in the European
features or specifications of the device.
Union and other European countries with
 Depending on the device to be connected, it may require
separate collection systems)
some time to start communication.
Note
 In the Operating Instructions, "iPod" is used as a general
reference to functions on an iPod, iPhone or iPad, unless
On Copyrights and Licenses
otherwise specified by the text or illustrations.
The Bluetooth word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by Sony
If you have any questions or problems concerning your unit,
Corporation is under license. Other trademarks and trade
please consult your nearest Sony dealer.
names are those of their respective owners.
General information
iPhone, iPod, iPod classic, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries. iPad is a trademark of Apple Inc.
"Made for iPod, " "Made for iPhone, " and "Made for iPad"
Specifications
mean that an electronic accessory has been designed to
connect specifically to iPod, iPhone, or iPad, respectively,
and has been certified by the developer to meet Apple iPod
performance standards. Apple is not responsible for the
DC out: 5 V
operation of this device or its compliance with safety and
MAX: 2.1 A
regulatory standards. Please note that the use of this
Radio
accessory with iPod, iPhone, or iPad may affect wireless
performance. Frequency range
Band Frequency
Precautions
FM 87.5 MHz - 108 MHz
 To disconnect AC power, grasp the plug itself, not the Bluetooth
cord.
Output
 Since a strong magnet is used for the speaker, keep credit
Bluetooth Specification Power Class 2
cards using magnetic coding or spring-wound watches,
Maximum communication range
CRT-based TVs, or projectors, etc., away from the unit to
Line of sight approx. 10 m*
prevent possible damage from the magnet.
 Do not leave the unit in a location near a heat source such Frequency band
as a radiator or airduct, or in a place subject to direct 2.4 GHz band (2.4000 GHz – 2.4835 GHz)
sunlight, excessive dust, mechanical vibration, or shock.
Communication System
 Allow adequate air circulation to prevent internal heat
Bluetooth Specification Version 2.1 + EDR (Enhanced Data
build-up. Do not place the unit on a surface (a rug, a
Rate)
blanket, etc.) or near materials (a curtain) which might
Compatible Bluetooth Profiles *
block the ventilation holes.
A2DP (Advanced Audio Distribution Profile)
 Should any solid object or liquid fall into the unit, unplug
AVRCP* 3 (Audio/Video Remote Control Profile)
the unit and have it checked by qualified personnel before
Supported codec *
operating it any further.
SBC (Subband Codec)
 During a thunderstorm, do not touch the antenna (aerial)
and plug. *
1 The actual range will vary depending on factors such as obstacles
 Do not touch the unit with wet hands. between devices, magnetic fields around a microwave oven, static
 Do not place the unit anywhere near water. electricity, reception sensitivity, aerial performance, operating
system, application software, etc.
NOTES ON LITHIUM BATTERY
*
2 Bluetooth standard profiles provide the specifications for
 Wipe the battery with a dry cloth to assure a good
Bluetooth communication between devices.
contact.
* 3
Some operations may not be available for some models of iPod.
 Be sure to observe the correct polarity when installing the
*
4 Codec: Audio signal compression and conversion format
battery.
 Do not hold the battery with metallic tweezers, otherwise
General
a short-circuit may occur.
Speaker
On Bluetooth communication
Woofer: Approx. 76 mm dia. × 2
 Bluetooth wireless technology operates within a range of Tweeter: Approx. 25 mm dia. × 2
about 10 meters.
Input
Maximum communication range may vary depending on
AUDIO IN jack (ø 3.5 mm stereo minijack)
obstacles (human body, metal, wall, etc.) or
Impedance: 50 kΩ
electromagnetic environment.
Average input level: 245 mV
Power output
The unit
20 W + 20 W (at 1% harmonic distortion) (with AC
adaptor)
7 W + 7 W (at 1% harmonic distortion) (with rechargeable
battery)
Steel cabinet Power source
Rated external power source: DC IN 20 V (with supplied
Optimal performance
AC adaptor (AC 100 V - 240 V, 50 Hz/60 Hz) or
Limited performance
rechargeable battery pack NH-300RDP)
 The following conditions may affect the sensitivity of
Battery life*:
Bluetooth communication.
Approx. 7 hours (playback of iPod)
— There is an obstacle such as a person, metal, or wall
Approx. 7 hours (FM reception)
between this unit and iPod.
Approx. 6.5 hours (Bluetooth playback)
— A device using 2.4 GHz frequency, such as a wireless
Dimensions
LAN device, cordless telephone, or microwave oven, is
Approx. 356.0 mm × 168.1 mm × 121.7 mm (w/h/d)
in use near the unit.
(incl. projecting parts and controls)
— The unit is installed on a shelf made of steel.
Mass
Approx. 2.6 kg
Supplied accessories
4-400-213-92(1)
Remote control (with a lithium battery) (1)
AC adaptor (1)
AC power cord (1)
Operating Instructions (this document) (1)
Cushion for small-size iPod (1)
*
Measured by Sony standards. The actual battery life may vary
depending on the circumstance of the unit.
Compatible iPod/iPhone/iPad
Operating Instructions GB
models
The compatible iPod/iPhone/iPad models are as follows.
Update the software of the iPod/iPhone/iPad to the latest
version before using it with this unit.
Dock Connector compatible models
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod nano (6th generation)*
iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod classic 160GB (2009)
iPhone 4S
iPhone 4
iPhone 3GS
iPhone 3G
iPad 2
iPad
Wireless music streaming compatible models
iPod touch (4th generation)
iPod touch (3rd generation)
iPod touch (2nd generation)
iPhone 4S
iPhone 4
iPhone 3GS
iPhone 3G
iPad 2
iPad
*
The iPod nano (6th generation) cannot be controlled by the
remote when the command of "MENU, " ", " ", " and "ENTER" is
pressed.
Design and specifications are subject to change without
notice.
Troubleshooting
General
The power does not turn on when the AC adaptor is
connected.
 Make sure the AC adaptor is connected to the wall outlet
firmly.
The rechargeable battery is depleted.
 Connect the AC adaptor to charge the battery.
There is no sound.
 Adjust VOLUME +/− (VOL +/− on the remote).
Noise is heard.
 Ensure that the unit is not near in-use portable phones,
etc.
The power will not turn on when the AC adaptor is
disconnected.
 The Power Off Hold function may be set. In this case,
cancel the Power Off Hold function. (See "Power Off
Hold function. " )
 The rechargeable battery may be depleted. In this case,
connect the AC adaptor to charge the battery. (See "To
use the AC adaptor. " )
"ERROR" appears in the display and the unit turns off
automatically.
 If this symptom occurs frequently, consult your nearest
Sony dealer.
When using an iPod on the Dock
There is no sound.
 Make sure the iPod is connected firmly.
 Make sure that the function for iPod is activated.
Operation is not performed.
 Make sure the iPod is connected firmly.
 Check that the iPod is compatible with this unit. (See
"Dock Connector compatible models. " )
The iPod does not charge.
 Make sure the iPod is connected firmly.
 Make sure the AC adaptor is connected firmly.
 Check that the iPod is compatible with this unit. (See
"Dock Connector compatible models. " )
When using the Bluetooth connection
There is no sound.
 Ensure that this unit is not too far from the iPod, or this
unit is not receiving interference from a wireless LAN,
other 2.4 GHz wireless device, or microwave oven.
 Check that the Bluetooth connection is made properly
between this unit and the iPod.
 Pair this unit and the iPod again.
 Keep away from metal objects or surfaces.
 Make sure that the Bluetooth function is activated.
Sound skips or the correspondence distance is short.
 If a device that generates electromagnetic radiation, such
as a wireless LAN, other Bluetooth device(s), or a
microwave oven is nearby, move away from such sources.
 Remove any obstacle between this unit and the iPod or
move away from the obstacle.
 Locate this unit and the iPod as close to each other as
possible.
 Re-position this unit.
 Re-position the iPod.
Connecting cannot be done.
 Perform pairing again. (See "To pair with an iPod. " )
 Check that the iPod is compatible with this unit. (See
"Wireless music streaming compatible models. " )
Pairing cannot be done.
Frequency step
 Bring this unit and the iPod closer together.
0.05 MHz
 Delete the unit from the iPod and perform pairing again.
 Check that the iPod is compatible with this unit. (See
"Wireless music streaming compatible models. " )
Radio
Reception is poor.
1
 Extend the aerial to its full length, and orientate for best
FM reception.
2
4
The sound is weak or is of poor quality.
 If the unit is close to a TV, move it away from the TV.
The TV picture is unstable.
 If you are listening to an FM program near a TV with an
indoor aerial, move the unit away from the TV.
Audio-in
There is no sound.
 Make sure the audio connecting cable is connected firmly.
 Make sure that the connected optional component is in
playback mode.
 Make sure that the Audio-in function is activated.
The sound is low.
 Check the volume of the connected optional component.
Remote control
The remote does not function.
 The unit cannot be turned on with the remote when the
AC adaptor is disconnected. In this case, press  on
the unit to turn it on.
 Replace the battery in the remote with a new one if it is
weak.
 Make sure that you are pointing the remote at the remote
sensor on the unit.
 Do not cover or place any objects directly in front of the
(Remote sensor) receiver.
 Remove any obstacles in the path of the remote and the
unit.
 Make sure the remote sensor is not exposed to strong
light such as direct sunlight or fluorescent lamp light.
If the problem persists, consult your nearest Sony dealer.
Preparations Remote control
Before using the supplied remote for the first time, remove
Power source the insulation film.
Aim the remote at the
Auto power off
After playback of the music (from an iPod on the Dock,
Bluetooth connection, or optional component connected to
the AUDIO IN jack) has finished, and if no operation is
performed for about 20 minutes, the unit will automatically
turn off.
Notes
 While the unit is turned on, if no operation is performed
for more than about 30 seconds, the display turns off. In When to replace the battery
this case, press SOUND to turn on the display again.
With normal use, the battery (CR2025) should last for about
 The unit cannot be turned on with the remote when the
6 months. When the remote can no longer operate the unit,
AC adaptor is disconnected.
replace the battery with a new one.
To use the AC adaptor
1
Connect the supplied AC power cord to the AC
adaptor.
2
Connect the AC adaptor to the DC IN 20V jack on
the back of this unit firmly and plug it into a wall
outlet.
Note on the AC adaptor Note
 If you are not going to use the remote for a long time, remove
 Use the supplied Sony AC adaptor only. The polarity of
the battery to avoid any damage that may be caused by
the plugs of other manufacturers may be different. Failure
leakage or corrosion.
to use the supplied AC adaptor may cause the unit to
malfunction.
Other useful functions
Power Off Hold function
3
Confirm that charging has started.
You can set the Power Off Hold function to avoid
When charging starts, the battery indicator appears.
unintentionally powering on while carrying the unit.
While charging, the charging indicator animation loops.
To set the Power Off Hold function
When the unit is turned off
Remove the iPod from the Dock Connector, and then press
and hold  on the unit when the AC adaptor is
disconnected.
"HOLD" flashes twice and the display turns off. The unit
When charging completes, the full battery indicator appears
cannot be turned on by pressing  while the Power Off
for a while, and then disappears.
Hold function is set.

To cancel the Power Off Hold
function
Notes
Press and hold  on the unit.
 If you connect the AC adaptor when the battery is fully
"RELEASE" flashes twice and the Power Off Hold function
charged, the full battery indicator appears for a while, and
is canceled. The unit will turn on automatically.
then disappears.
Tip
 If you connect the AC adaptor when the battery power is
 The Power Off Hold function will be canceled if you
low, charging starts and the low battery and charging
connect the AC adaptor to the unit or set an iPod on the
indicator animation loops.
Dock Connector.
The unit cannot be operated without the AC adaptor while
the low battery indicator appears.
Selecting audio emphasis
 
(equalization)
You can adjust the emphasis of the sound.
Press SOUND
When the unit is turned on
emphasis.


When charging completes, the full battery indicator


appears.


Note
 It will take approximately 6 hours to fully charge the
battery.
To use the rechargeable battery 

You can operate the unit with the rechargeable battery
instead of the AC adaptor.
Note

 The maximum output volume will be lower when the AC 
adaptor is disconnected.
To check the remaining power of the battery
The remaining power of the battery will be indicated when
the unit is turned on. As the remaining battery power
About App
depletes, the battery indicator decreases.
A dedicated Dock App for iPod touch/iPhone/iPad available
at Apple App Store.
Search for "D-Sappli" and download the free App to find
out more about the functions.
Features
Level 1 Level 2 Level 3 Level 4
 D-Sappli includes various timer functions: Alarm, Music
Play Timer and Sleep Timer.
When the battery becomes almost fully depleted, "LOW
 You can set up to 10 alarms, using songs in iPod or Preset
BATT" flashes and the unit will turn off. To charge the
Sound in D-Sappli for the alarm sound.
battery, connect the AC adaptor. (See "To use the AC
Music Play Timer allows you to play/pause desired music
adaptor. " )
at a desired time. Sleep Timer allows you to specify a time
 
at which to stop music playback. Alarm, Music Play
Timer and Sleep Timer work in combination with the
power supply of the unit.
Alarm, Music Play Timer and Sleep Timer are available
Notes
only when D-Sappli is activated.
 The remaining battery power will not be indicated when
 D-Sappli can display a list of Radio Preset Stations
the unit is turned off.
programmed in this unit.
 The unit requires at least 30 minutes to charge the battery
You can rename the Radio Preset Stations, and change
if "LOW BATT" appears.
their preset numbers on the D-Sappli. Preset numbers
 The battery indicator shows approximate remaining
and order will also be changed accordingly in the unit.
battery power.
 D-Sappli also includes a clock display enlarge feature.
 Operating conditions will affect the rate of battery
depletion.
Notes
When to replace the rechargeable battery
 If the App to link with this unit is not downloaded to the
Repeated recharging causes the duration of the battery iPod touch/iPhone/iPad, a pop-up message prompting
power to decrease over time. Replace the battery pack when you to download D-Sappli may appear repeatedly.
its duration becomes half the usual period, even after Deactivate the App's link function to stop the pop-up
message.
charging it fully.
 To deactivate the App's link function: Connect the AC
Note
adaptor, and then press / to turn off the unit. Remove
 The rechargeable battery pack is not a commercially
the iPod touch/iPhone/iPad from the Dock Connector.
available product. To purchase rechargeable battery pack
While holding down , also press and hold / on the
(NH-300RDP), consult your nearest Sony dealer.
unit for at least 2 seconds. ("App OFF" appears in the
To replace the rechargeable
display to show that the App's link function has been
battery deactivated.)
 To re-activate the App's link function, repeat the above
1
Remove the screw of the battery compartment at
steps. ("App ON" appears in the display to show that the
App's link function has been activated.)
the bottom of the unit, and open the lid.
2
Disconnect the connector of the battery pack and
pull it out.
3
Insert a new battery pack and connect its
connector to the jack.
4
Replace the battery compartment lid and tighten
the screw.
Notes
 When replacing the battery pack, place a soft cloth etc.,
under the unit.
 Turn off the unit and disconnect the AC adaptor before
removing the old battery pack.
 Charge a new battery pack before use. For details, see "To
use the AC adaptor. "
(Remote sensor) of the unit.
 side facing up
repeatedly to select the desired audio
Continued on the reverse side