Sony PLM-S700E Service Manual page 68

Pin No. Pin Name
43 XCS OSD
44 MOD UNDEF
45 PLL ERROR
46 MOD CHG
47 OSD TRE
48 XALVS ON
49 DBB MID ON
50 DBB NORM ON
51 VDD
52 32KHZ IN
53 32KHZ OUT
54 VSS
55 3D ON
56 3D L/R
57 XTG RES
58 OSD DISP
59 EXT/XINT
60 —
61 BATT IN
62 XVSYNC
63 XS DET
64 XEXT 3D IN
65 MENU A
66 MENU B
67 BRIGHT B
68 BRIGHT A
69 —
70 TEMP
71 BATT SENS
72 CHARGE A/D
73 DC IN A/D
74 AVSS
75 AVREF0
76 AVREF1
77 AVDD
78 HSYNC DET
79 VSYNC DET
80 POL H
81 POL V
82 XLOOK ON
XVIDEO
83
SYNC DET
I/O
O
Chip select signal output to the on screen display controller (IC401) "L" active
O Output terminal for the test (signal judgment result uncertain ("H" active)) Not used (open)
O
Output terminal for the test (PLL communication (7h) error ("H" active)) Not used (open)
O
Output terminal for the test (signal judgment result variable (toggle)) Not used (open)
Monitor input during transfer operation from the on screen display controller (IC401)
I
"H" active
O
AVLS on/off control signal output to the headphone amplifier (IC151) "L": AVLS on
O DBB control signal output to the headphone amplifier (IC151) *1
O
DBB control signal output to the headphone amplifier (IC151) *1
—
Power supply terminal (+5V)
I
Sub system clock input terminal (32.768 kHz) (for clock)
O Sub system clock output terminal (32.768 kHz) (for clock)
—
Ground terminal
O
Control signal output for the 3D (L & R independent) screen display "H" active
O
3D L/R picture selection inverted output terminal Not used (open)
O
Reset signal output to the LCD timing generator (IC301) "L": reset
Display outputs (R/G/B OUT, IOUT, VOB1, VOB2) control signal output to the on screen
O
display controller (IC401)
Sync selection signal output to the sync signal select switch (IC447, 451)
O
"L": internal sync signal selection, "H": external sync signal selection
O
Not used (open)
I
Power failure detection signal input terminal
I
Vertical sync signal interruption input from the LCD timing generator (IC301) "L" active
I Connection detect signal input of the S terminal (S video in jack J1401) "L": connection
I
External 3D signal input terminal "L" active Not used (fixed at "H")
I
Jog dial pulse input from rotary encoder (S905) for the menu setting (A phase input)
I
Jog dial pulse input from rotary encoder (S905) for the menu setting (B phase input)
I
Jog dial pulse input from rotary encoder (S1301) for the BRIGHT control (B phase input)
I
Jog dial pulse input from rotary encoder (S1301) for the BRIGHT control (A phase input)
I
Not used (fixed at "L")
I Connection terminal of the board temperature sensor (analog input)
I
Input of the battery capacity detection (analog input)
I
Input of the charging voltage and battery voltage detection (analog input)
I
DC input voltage detection (analog input)
— Ground terminal (for A/D converter)
I
Reference voltage (+5V) input terminal (for A/D converter)
I
Reference voltage (+5V) input terminal (for A/D converter)
—
Power supply terminal (+5V) (for A/D converter)
External horizontal sync detection signal input from the CXA1616N (IC443)
I
"H": horizontal sync signal detected
External vertical sync detection signal input from the CXA1616N (IC443)
I
"H": vertical sync signal detected
External horizontal sync polarity input from the CXA1616N (IC443)
I
"L": positive polarity, "H": negative polarity
External vertical sync polarity input from the CXA1616N (IC443)
I
"L": positive polarity, "H": negative polarity
I
Picture watching detection signal input terminal "L": picture watching
I
Video signal sync detection signal input terminal "L": sync signal detected
Function
4-95