IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
MX1Z PANEL LAYOUT Control Unit •Front Panel RECORD SONG SELECT/RV VOLUME -10 -8 PLAY/PAUSE STOP • CONTROL UNIT TEMPO GENERAL INSTRUMENT PART SELECT TRANSPOSE BALANCE STANDBY - ON METRO- ENTER –/NO +/YES VOICE FUNC. NOME 15 16 17 [STANDBY - ON] button Floppy disk eject button Remote control sensor [ENTER] button...
MX1Z WIRING Buttons, LED Rotary POWER 24char*2line Encoder Control Unit 7 SEG. PANEL SWITCH EMK-CTL REMO-CON RECEIVE FLASH FLASH DRAM (Memory (PROGRAM) 512Kb Disk) SPEAKER CTRL SUB A SH/CPU M3888 UART MIDI HOST to HOST SEL. SW mini D-SUB 15 CN101 HAMMER EMISSION HAMMER...
MX1Z DISASSEMBLY PROCEDURE Cabinet Parts and Action Stopper Upper Front Board Open the top board. (Fig. 1) Loosen the screw marked [A] and turn the stopper. (Fig. 1) Upper front board Turn the left and right knobs. The upper front board can then be removed.
Page 9
MX1Z Electrical Parts [41GA] Top cover [31GA] DB Circuit Board [33GA] [41GA] Remove the four (4) screws marked [33GA] and the five (5) screws marked [41GA]. The top cover can then be removed. (Fig. 3) Remove the three (3) screws marked [31GA]. The DB [33GA] circuit board can then be removed.
Page 10
MX1Z LCD Assembly LED 7 SEG. Remove the top cover. (See Procedure B-1-1.) POWER SWITCH PANEL SWITCH Remove the panel unit. (See Procedure B-6.) [32GB] Remove the structure. (See Procedure B-7-3.) Remove the three (3) screws marked [32GA]. The LCD [31GD] [32GA] assembly can then be removed.
Page 11
MX1Z HAMMER EMISSION Circuit Board, Hammer sensor unit HAMMER SENSOR Circuit Board 13-1 Open the top board. (Fig. 1) 13-2 Remove the upper front board. (See Procedure A-1.) 13-3 Remove the keyboard cover. (See Procedure A-2.) HAMMER SENSOR 13-4 Remove the key stop rail. (See Procedure A-3.) 13-5 Remove the action unit.
Page 12
MX1Z Plunger Assembly and Coil Assembly [8G] Plunger assembly 16-1 Open the top board. (Fig. 1) 16-2 Remove the upper front board. (See Procedure A-1.) 16-3 Remove the keyboard cover. (See Procedure A-2.) 16-4 Remove the key stop rail. (See Procedure A-3.) Upper yoke 16-5 Remove the action unit.
Page 13
MX1Z Switch Box Assembly 18-1 Remove the four (4) screws marked [73S]. The switch box assembly can then be removed. (Fig. 11) [73S] Switch box assembly MAINS FOOT CONTRL MAINS (ON/OFF) switch [73S]: Truss Head Tapping Screw-1 4.0 x12 MFZN2BL (03747270) (Fig.
Page 15
MX1Z HD63266F (XI939A00) FDC (Floppy Disk Controller) EMK-CTL: IC202 NAME FUNCTION NAME FUNCTION 8"//5" Data transmission speed /TRKO Track 00 signal XTALSET Clock select /INDEX Index signal /RESET Rest /RDATA Read data input from FDD E//RD Enable/Read XTAL2 Clock RW//WR Read/write/Write EXTAL2 Chip select...
Page 16
MX1Z LC92011B-656 (XK441A00) GATE ARRAY PK-CTL: IC7 NAME FUNCTION NAME FUNCTION Frequency 0 16 M Frequency 1 8 M Frequency 2 4 M 1SHOT One shot Data bus OK1S OK one shot TESTIN Test pin, not used RESET Reset Reset Address Iatch enable /RES Reset...
Page 17
MX1Z RF5GF26-028 (XK652A00) GATE ARRAY HAMMER SENSOR: IC3 NAME FUNCTION NAME FUNCTION Not used Not used Power supply Power supply IRQKB Interrupt Key OCTK0 OCTK1 OCTK2 Make 1 OCTK3 Oct. Key OCTK4 OCTK5 OCTK6 Clock OCTK7 SYSRESIB Reset Note OCTM10 OCTM11 OCTM12 OCTM13...
Page 18
MX1Z YM3421-F (XL150A00) PWM GENERATOR DRIVE A: IC1, DRIVE B: IC1 NAME FUNCTION NAME FUNCTION Data bus Key drive pulse Ground Key drive pulse Key drive pulse Ground Power supply øM Clock Initial clear Chip select Key drive pulse Address enable Touch data enable Data bus HD6433258C02F (XQ462C00) CPU...
Page 19
MX1Z HD6417032-F20 (XQ958A00) CPU EMK-CTL: IC103 NAME FUNCTION NAME FUNCTION PB14 IRQ from SCI CPU /IRQ7 IRQ from FDC /WRH Not used Data 0 FDC TEND Data 1 Data 2 Remote-control reset Data 3 4 M FLASH Ready Data 4 PWMB Not used Data 5...
MX1Z CONTROL BOARD ***** TEST MODE ***** • Title display **** CONTROL SHEET **** VO. 13 Oct 12 1996 Test & Loader : V1 . 11 Japananese UPS DB51 Japanese UPS DB51 CTRL Program Version No. – Test program version No. English Japanese can be changed by (L), (R) button.
MX1Z ERROR MESSAGES While operating your Disklavier an error message may appear in the display. If an error message does appear, look in the table below for an explanation of the message. Note: This table does not explain every error message. PianoSoft songs cannot be re-recorded, as they are write-protected.
Page 26
MX1Z SENSOR OUTPUT VOLTAGE ADJUSTMENT (PEDAL DRIVE UNIT) a. Voltage adjustment of the loud pedal Adjustment the voltage with the VR1 and VR2 so that when the loud pedal is pressed, an output voltage of CNP pin #1 on the pedal sensor PCB will be 2.65 V or higher, the LED1 (red) will be lit, and the output voltage will be 3.50±0.1 V. b.
Page 27
MX1Z WRITING NEW PROGRAM TO FLASH MEMORY Inclusion of flash memory onto the control sheet had enabled the following operations. (1) Record to and replay from the flash memory: 1 MB (2) Program: 512 KB On the MPX1D, the upgrade program is supplied on floppy disk so that it can be copied directly into flash memory, overwriting the existing version.
MX1Z CIRCUIT BOARDS CONTENTS •CTRL SUB A Circuit Board (XS386C0)······························································· 26 •CTRL IN Circuit Board (XR146A0) ······································································ 29 •DRIVE A Circuit Board (XL114D0) ······································································ 27 •DRIVE B Circuit Board (XL114D0) ······································································ 28 •DRIVE C Circuit Board (XL114D0) ······································································ 28 •EMK-CTL Circuit Board (XU914A0) ···································································· 24 •HAMMER EMISSION Circuit Board (XL119A0) ··················································...
Page 30
MX1Z PWB Circuit Board to Switch box to DRIVE A-CN34, 36 to PK-CTL-CN3 Component side to DRIVE C-CN214 PWB: VN54330, VN54340 to PEDAL DRIVE-CN1...
Page 31
MX1Z EMK-CTL Circuit Board TO CONTROL CABLE HOST FOR PIANO SELECT TO HOST Connector (EMK-CTL) CN101: to PK-CTL-CN1 (TO CONTROL CABLE FOR PIANO) CN102: to Rotary encoder CN103: to CTRL SUB A-CN3 CN104: to CTRL SUB A-CN5 CN105: to DB Circuit Board CN106: to CTRL SUB A-CN7 CN107: to CTRL SUB A-CN8 CN108: N.C.
Page 32
MX1Z EMK-CTL Circuit Board Pattern side PK-CTL Circuit Board Pattern side EMK-CTL: V252040 PK-CTL: V482950...
Page 33
MX1Z PANEL SWITCH Circuit Board Component side LED FUNCTION TABLE SWICH FUNCTION TABLE LED 1 VOLUME -0 LED 13 TEMPO PLAY/PAUSE LED 2 VOLUME -1 LED 14 TRANSPOSE STOP SW10 LED 3 VOLUME -2 LED 15 PLAY/PAUSE RECORD SW11 -/NO LED 4 VOLUME -3 LED 16...
Page 34
MX1Z DRIVE A Circuit Board Component side Connector (DRIVE A) CN2: to KEY 25, 57 CN10: to KEY 33, 65 CN18: to KEY 41, 73 CN25: to KEY 48, 80 CN32: to KEY 55, 87 CN3: to KEY 26, 58 CN11: to KEY 34, 66 CN19: to KEY 42, 74 CN26: to KEY 49, 81...
Page 35
MX1Z DRIVE B Circuit Board Component side Connector (DRIVE B) CN101: to PK-CTL-CN6 CN105: to KEY 16 CN109: to KEY 20 CN112: to KEY 23 CN115: to DRIVE C-CN201 CN102: to KEY 13 CN106: to KEY 17 CN110: to KEY 21 CN113: to KEY 24 CN116: to PEDAL DRIVE-CN5 CN103: to KEY 14...
MX1Z HAMMER SENSOR Circuit Board HAMMER EMISSION Circuit Board to KEY EMISSION-CN1 to HAMMER SENSOR-CN2 Component side CTRL IN Circuit Board FOOT to PK-CTL-CN8 CNTRL Component side Component side Pattern side HAMMER SENSOR: VT18690 HAMMER EMISSION: VN57170 CTRL IN: VT83650...
Page 37
MX1Z OVERALL CIRCUIT DIAGRAM 1/3 ( EMK-CTL, CTRL SUB A, PANEL SWITCH, POWER SWITCH, DB, LED 7SEG., LCD Module ) MX1Z PANEL SWITCH EMK-CTL not used not used not used not used F F C TO HOST CN401 (EMK-CTL) Pin No. Pin No.
Page 38
MX1Z OVERALL CIRCUIT DIAGRAM 2/3 ( DRIVE A, DRIVE B, DRIVE C, PK-CTL, PEDAL DRIVE, PEDAL SENSOR, CTRL IN, PWB ) MX1Z DRIVE C DRIVE B DRIVE A DRIVE A TRANSISTOR ARRAY TRANSISTOR ARRAY TRANSISTOR ARRAY TRANSISTOR ARRAY YM3421-F YM3421-F YM3421-F VN588400 PWM GENERATOR...
Page 39
MX1Z OVERALL CIRCUIT DIAGRAM 3/3 ( HAMMER SENSOR, HAMMER EMISSION, KEY RECEIVER, KEY EMISSION ) MX1Z KEY RECEIVER KEY EMISSION HAMMER SENSOR INVERTER RESET INVERTER PHOTO COUPLER to PK-CTL -CN2 COMPARATOR COMPARATOR VZ141900 HAMMER EMISSION VT186900 VN244500 Note: See parts list for details of circuit board component parts. VN571700 MX1Z BLOCK DIAGRAM CTRL IN...
MX1Z OVERALL ASSEMBLY Control Unit 031S 182S 182S Center Rail 027S Hammer Sensor Unit View A 058S 057S 056S 052S 054S 051S Key Drive Unit 102S 073S 055S 053S Switch Box Assembly 081S Label (Pedal adjustment) (E) Base Board View D Pedal Drive Unit 126S 101S...
Page 43
MX1Z Control Unit Hammer Cushion 128S 125S Hammer Sensor Unit View C 021S 181S 044S 048S 041S Key Sensor Unit 091S Pedal Drive Unit 113S View B...
MX1Z CONTROL UNIT Rear View 12 22 26 Top View Side view 31G 5 7 25 31G 14 Front View Bottom View...
Page 48
MX1Z PART NO. DESCRIPTION REMARKS REF NO. RANK CONTROL UNIT DKC500RWXG MX1Z Control Unit DKC500RWXG (V521710) Control Unit DKC500RWXG (V521750) Control Unit DKC500RWXG (V521770) V5218500 Panel Unit V5218600 Panel Unit V5218700 Panel Unit VV091400 Bottom Chassis PBL,BL VV258500 Bottom Chassis Top Cover PBL,BL VV091700...
MX1Z POWER SUPPLY ASSEMBLY PART NO. DESCRIPTION REMARKS REF NO. RANK POWER SUPPLY ASSEMBLY MX1Z VN812300 Power Supply Assembly U,APTW VN812500 Power Supply Assembly E,B,APTH,APHK,A PWB Unit U,APTW VN812700 VN812800 PWB Unit E,B,APTH,APHK,A VN543300 Circuit Board U,APTW VN543400 Circuit Board E,B,APTH,APHK,A DB Unit U,APTW...