To reduce the risk of fire or electric shock, do not expose this appliance to This product has been manufactured by or on behalf of Sony Corporation, dripping or splashing, and do not place objects filled with liquids, such as 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan.
In case of products that for safety, performance or data integrity reasons CAUTION require a permanent connection with an incorporated battery, this battery Danger of explosion if battery is incorrectly replaced. should be replaced by qualified service staff only. Replace only with the same or equivalent type. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical Disposal of Old Electrical &...
Page 4
United States and in other countries. The BLUETOOTH® word mark and logos are registered trademarks owned by BLUETOOTH SIG, Inc. and any use of such marks by Sony Corporation is under license. LDAC™ and LDAC logo are trademarks of Sony Corporation.
Table of contents WARNING ................2 Copyrights ................3 Precautions ................6 Changing the battery of the remote control ......7 Turning off BLUETOOTH ............8 Resetting the unit ..............8 Troubleshooting ..............9 Specifications ............... 12 On BLUETOOTH® Communication ........14 End users license agreement ..........15 Refer to the supplied “Operating Instructions”...
If you have any questions or problems concerning your system, please it is connected to the wall outlet, even if the unit itself has been turned off. consult your nearest Sony dealer. If you are not going to use the system for a long time, be sure to disconnect the unit from the wall outlet.
Replace the battery with the “+” facing up, then insert the Changing the battery of the remote control battery holder into the slot. + facing up The working distance of the remote shortens as the battery becomes exhausted. When the remote no longer operates the unit, replace the battery with a new CR2032 lithium battery (not supplied).
Turning off BLUETOOTH Resetting the unit Press the (on/standby) button of the unit to turn on the If the unit still does not operate properly even after checking the troubleshooting, or when you fail setting, reset the unit. unit. Press the ...
The unit turns off automatically. repairs. Should any problem persist, consult your nearest Sony dealer. Check the AUTO STANDBY switch on the rear side of the unit. If it is set to “ON,”...
Page 10
Touch the N-Mark of the Walkman or the smartphone on the N- Left and right sound balance is unclear or reversed. Mark of the unit. If the device does not respond even though it is Position the speakers symmetrically. touched to the unit, move it slowly to the front, rear, left and right.
Page 11
Point the remote to the remote sensor (the circuit of the (on/ unit, make sure the dedicated driver is installed to the PC. Check that the sound device setting of your computer is set to “Sony standby) button) of the unit.
20 W + 20 W (5 Ω, 20 Hz - 20 kHz, THD 1%) Advanced Audio Coding Speaker impedance match LDAC is an audio coding technology developed by Sony that enables 5 Ω - 16 Ω the transmission of High-Resolution (Hi-Res) Audio content, even over Frequency response 10 Hz - 40 kHz (+0 dB, –3 dB) (5 Ω, B (USB-B) input)
Page 13
Supported USB device Speaker System (SS-HW5) Mass Storage Class (MSC) Maximum output current Speaker system 1A MAX 2 way, 2 drivers speaker system, Bass reflex Depending on the device, the charge current might be limited to Speakers unit 500 mA. Tweeter: 14 mm, soft dome type ×...
Note worldwide. Sony cannot accept responsibility in the event that data recorded to Maximum communication range iPhone/iPod is lost or damaged when using your iPhone/iPod connected to this unit.
Noise or sound skips may occur depending on the BLUETOOTH device name “CAS-1”. connected with the system, the communication environment or the URL: http://oss.sony.net/Products/Linux/ usage environment. Please note that Sony cannot answer or respond to any inquiries regarding the content of the source code.