Advertisement
Quick Links
Cordless Screwdriver
Wood screws
Machine screws
MODEL 6710D
MODEL 6710DW
With Fast Charger
weight
speed
length
Nuts
INSTRUCTION MANUAL
5
1
mm x
50
mm
11.4' x 2 ' l
I
SPECIFICATIONS
6
mm
6
mm
220
195 mm
1 1
kg
f 114")
(1/4")
Rimin
17-518")
12.4 lhsl
Model 6 7 1 0 0
Battery Cartridge 7 0 0 0
Model OC7100 Fast charger
7 2 V
Dimensions
iL
x
W
x
H)
A.C only
D C
1 4 5
mm
x
8 0 mm x 61 mm
0
7 k g
5 0 H r
60 H r
7 2 V
( 5 314"
x
3
1/8"
x
2 318")
I1 5
lhsl
1
Hr
Net
1
weight
Advertisement
Related Manuals for Makita 6710D
Summary of Contents for Makita 6710D
- Page 1 11.4' x 2 ' l f 114") Battery Cartridge 7 0 0 0 Model OC7100 Fast charger A.C only 7 2 V 5 0 H r MODEL 6710D MODEL 6710DW speed Nuts (1/4") Rimin Dimensions 1 4 5...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turn- AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
- Page 4 Before using battery charger, read all instructions and cautionary markings battery charger, To reduce risk of injury, charge only MAKITA Battery 7000. CAUTION Other types of .batteries may burst causing personal injury and damage.
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents.
- Page 6 Installing or removing battery cartridge Always switch off the tool before insertion To remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip place.
- Page 7 Switch action Set the reversing switch lever just in front of the trigger switch to Forward (FWD) or Reverse (REV). Then pull the trigger to turn the tool ON and release it to turn OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the switch lever to the opposite side.
- Page 8 Fastening torque adjustment The fastening torque may be adjusted by turning the adjustment ring to align the notched line on the ring with a number on the indicator label. However, the clearance between the ring and the cap mm (1/8") maximum after one full turn, and the ring should not be forced beyond this point.
- Page 9 Hole 0The hole on the heel of the tool is a con- venient way to carry or other means. Drill chuck (Accessory) To install a drill chuck, remove the insert bit by a strong jerk, then be replaced with the insert bit by a sharp push of the hand.
- Page 10 Screwdriving Match your bit to your screw. Phillips bits Select your screws on and the nominal meter with the chart Slotted bits Select a slotted bit to match the slot on the screw heads. If the bit is too small for the screw slot, the bit and/or screw head may be damaged.
- Page 11 Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
- Page 12 CAUTION: These accessories or attachments are recommended for use w i t h y o u r Makita t o o l specified in this manual. The use o f any other accessories o r attachments m i g h t present a risk The accessories or attachments should be used o n l y in t h e proper and intended manner.
- Page 13 Battery holster Carrying case Plastic case Holster holds Steel case battery. extra 181428-2 Part N ~ , 823087-3 part Part No. 823033-3C...
- Page 14 -09-'84 CORDLESS SCREWDRIVER Model 67100 Note: The switch and other part configurations may differ from country to country.
- Page 15 MODEL 67101D ’ E M $&, DESCRIPTION MACHINE Adlust Torque Ring Ring Guide Plate Washer 14 Lock F Washer 1 4 Leal sprang Sled Ball Spindle Compression Spring 14 T Washer 1 0 Clutch Cam Steel Ball 6 Spur Gear 86 Note The switch and other part specifications may differ from country to &...
- Page 16 MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.