Table of Contents
Advertisement
Quick Links
n
Capacities
Bolt
size
Square drive
Standard bolt
High tensile
bolt
I
\-
Impacts per minute
A t high speed
A t
low
speed
12.7 mm (1/2") MODEL 6900D
12.7 mm (1/2")
MODEL 6900DW
With Fast Charger
M8 -
M 1 4 15/16"
-
9 / 1 6 " )
INSTRUCTION MANUAL
M E
-
M 1 0 15/16"
~
318")
1 2 7
m m
11/2"l
2,000
1 , 5 0 0
SPECIFICATIONS
No
load speed IRPMI
Model
6900D
Overall
Net
Tightening torque
length
High
LOW
At
high speed
A t low speed
weight
1,500
1
,,300
I
1 , 0 0 0 kg.cm 172
ft.lbs1
I
400
kg.cm 129
tt.lbsl
2 2 6
mm
1 . 7 kg
Note
1
Note 2
I
18-718")
I
13.7
lbsl
Battery
Canridge
9000
Model D C 9 1 0 0
Fast
Charger
9 6 V
I
1
nr
I
A C o n l v 5 0 H z - 6 0 H z
I
D C 9 6 V
Voltage
Note 1. After tightening high tensile bolt M12 for
E
seconds while using a fully charged battery cartridge.
Note 2. After tightening high tensile bolt M10 for
E
seconds while using a fully charged battery cartridge.
*
Manufacturer reserves the right to change specifications without notice.
*
Note: Specifications may differ from country to country.
Charging time
Input
OUtPUt
Advertisement
Table of Contents
Related Manuals for Makita 6900D
Summary of Contents for Makita 6900D
- Page 1 Note 1. After tightening high tensile bolt M12 for Note 2. After tightening high tensile bolt M10 for Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. 12.7 mm (1/2") MODEL 6900D 12.7 mm (1/2") Square drive High tensile bolt M 1 0 15/16"...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch OUTDOOR USE EXTENSION extension cords intended for use outdoors and so marked.
- Page 4 Before using battery charger, read all instructions and cautionary markings on (1) battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Other types of batteries may burst causing personal injury and damage. 4. Do not expose charger t o rain or snow.
-
Page 5: Additional Safety Rules
ADDITIONAL FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anythiqg t o cover or clog the charger vents. 4. - Page 6 Installing or removing battery cartridge Always switch off the tool before insertion remove the battery cartridge, pull out plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and place.
- Page 7 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is not indicate a problem. You can recharge it completely couple times. If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger.
- Page 8 Reversing switch and speed change switch action Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. Slide the speed change switch to the right for high speed (high tightening torque) or to the left for low speed (low tightening torque).
-
Page 9: Operation
Operation The proper tightening torque may differ depending upon the kind relation between tightening torque and tightening time is shown in the figures below. Standard bo1 t kg cm I f f . Ibrl M I 4 l9/16'1 at high rpssd High tensile bolt kg cm 1581... - Page 10 Speed Type of bolt High High tensile bolt Standard bolt M 8 CAUTION If the tool i s operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Tightening time 13/8") 3 seconds...
- Page 11 Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. maintain product SAFETY and should be performed Makita Authorized or Factory Service Centers, always using Makita replacement parts. RELIABILITY, repairs, maintenance or adjustment...
- Page 12 ACCESSOR I ES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended mannuer.
- Page 13 . ,. . : . i : . . h: ; , : : . .. ! . ? ._._ f ..: . .;:.$,: ,,., Phillips bit (Use with bit adapter) 784208- 1 45 (1-3/4") Fast charger Model D C 9 1 0 0 Battery cartridge 9 0 0 0 Part...
-
Page 14: Cordless Impact Wrench
Juna-Ol-'BB @- - 12.7 mm (1/2") CORDLESS IMPACT WRENCH Model 6900D Note: The switch and other part configurations may differ from country to country. - Page 15 MODEL 69000 $ $ D DESCRIPTION MACHINE Head M3x14 lWilh Washer1 Screw Switch Head M3.14 lWith Washer1 Screw TrlOga, Spring 2 Compression lWith Item 201 Hausmp S P " L. . l LWa, PI.". 0.anng 4 Gem Complete 11 PI.". n..rmg Motor 9 6 ORmp...
-
Page 16: One Year Warranty
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not apply where:...