Cisco Aironet 340 Series Quick Start Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Hardware
  5. Aironet 340 Series
  6. Quick start manual
Cisco Aironet 340 Series Quick Start Manual

Cisco Aironet 340 Series Quick Start Manual

Wireless
Hide thumbs Also See for Aironet 340 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual, Quick Start Manual

Quick Start Guide

C
A
340 S
I S C O
I R O N E T
E R I E S
W
B
I R E L E S S
R I D G E S
File server
LAN segment A
C
E/RS -232
CON SOL
12-1 8 VDC
I
Wireless bridge
(root unit)
Workstation A
E/RS -232
C
CON SOL
12-1 8 VDC
I
Wireless bridge
LAN segment B
(remote node)
Workstation B
1
T
O
W
Y
AKE
UT
HAT
OU NEED
2
C
P
U
B
ONNECT AND
OWER
P THE
RIDGE
3
C
B
ONFIGURE THE
RIDGE

Advertisement

Table of Contents
loading

Related Manuals for Cisco Aironet 340 Series

Summary of Contents for Cisco Aironet 340 Series

  • Page 1: Quick Start Guide

    Quick Start Guide 340 S I S C O I R O N E T E R I E S I R E L E S S R I D G E S File server LAN segment A E/RS -232 CON SOL 12-1 8 VDC Wireless bridge...

  • Page 3: Before You Begin

    Cisco Aironet 340 Series Wireless Bridge CD with product documentation If any item is missing or damaged, contact your Cisco representative or reseller for support. Before You Begin Before beginning installation, determine bridge location. Because the unit is a radio device, unit and antenna location are important to ensure optimum radio range and throughput: •...

  • Page 4: Installing The Antenna

    Connect and Power Up the Bridge Note: Before you install the bridge system, we recommend that you test the bridge using the 2.2 dBi antenna included in the package. Then install the wireless bridge with the appropriate antenna for your application. A lightning arrestor and low-loss antenna cable are included in the optional antenna kits or can be ordered separately.
  • Page 5 10 B as e 10 B as e 1 0B as e 1 0 B a s e 10Base2 connector 1 0 B a s e 1 0 B a s e 1 0 B a s e 1 0 B a s e 10Base5 10BaseT connector...

  • Page 6: Installing The Console Port Cable

    Installing the Console Port and Powering Up the Bridge The console port and power connections are on the side of the bridge. The console connection is required for setting up initial configuration information. After configuration is complete, you may remove this cable unless or until additional configuration is required via the serial port. On/off button E/R S-2 32C CO NS OL...

  • Page 7: Assigning Ip Information

    Configure the Bridge Assigning the SSID Assigning IP Information Use the console port to set the Service Set To enable remote access to the bridge using Identifier (SSID) that allows the wireless Telnet, HTTP, or SNMP, you must assign an bridge to communicate with other nodes.The IP address to the bridge.
  • Page 8 Once the bridge is configured as a root or non-root unit, you can quit the terminal emulator or browser, disconnect the console port cable, and install the bridge in its desired location before proceeding with remote configuration. Refer to the Aironet 340 Series Wireless Bridge User Guide on the product CD for details on configuration.
  • Page 9 ANSI C95.1, 1991. Proper operation of this radio according to the instructions found in this manual and the users guide on the Cisco Aironet 340 Series Wireless Bridge product CD will result in user exposure that is substantially below the FCC recommended limits.
  • Page 10 The Part 15 radio device operates on a non-interference basis with the other devices operating at this frequency. Any changes of modification to said product not expressly approved by Cisco could void the user’s authority to operate this device. Professional Installation...
  • Page 11 Systems operating as a point-to-multipoint system or using non-directional antennas cannot exceed +36 dBm EIRP power requirement under any circumstances and do not require professional installation. Department of Communications—Canada Canadian Compliance Statement This class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
  • Page 12 EtherSwitch, FastHub, FastLink, FastPAD, FastSwitch, GeoTel, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document are the property of their respective owners.

Table of Contents