Honeywell MX7 Tecton Quick Start Manual
Hide thumbs
Also See for MX7 Tecton:
- Reference manual (366 pages) ,
- User manual (354 pages) ,
- Reference manual (330 pages)
Related Manuals for Honeywell MX7 Tecton
Summary of Contents for Honeywell MX7 Tecton
-
Page 1: Mx7 Tecton
MX7 Tecton™ Hand-Held Computer ® With Microsoft Windows Embedded CE 6 or ® Windows Mobile 6.5 Operating System Quick Start Guide TECTON-QS Rev A 4/12... - Page 2 Setting up the MX7 Tecton Please have the following Information available before setting up your MX7 Tecton: Network ID (SSID) of the Access Point WEP key or LEAP authentication credentials 1. Insert a fully charged battery into the MX7 Tecton.
- Page 3 Bluetooth and MX7 Tecton Please refer to the MX7 Tecton Reference Guide for information when using the MX7 Tecton with Bluetooth. ActiveSync Installing ActiveSync on Desktop/Laptop ActiveSync (version 4.5 or higher for Windows XP desktop/laptop computers) must be resident on the host (desktop/laptop) computer.
- Page 4 The only connection type is USB Client. 1. Connect the MX7 Tecton end of the USB cable to the I/O port on the bottom of the MX7 Tecton. 2. Connect the USB type A connector on the I/O cable to a USB port on a PC or laptop.
-
Page 5: Setting Up The Radio
(WEP, LEAP, etc.), your radio must use the same authentication. Please contact your IT department for WEP keys or LEAP credentials. Please refer to the MX7 Tecton Reference Guide for information on using WPA. 1. Tap Start > Programs > Summit > SCU OR tap the Summit Client Utility icon on the desktop. - Page 6 13. Tap the Main tab. Wait for a radio connected message. 14. Tap the Admin Logout button when finished. 15. Reboot the MX7 Tecton. Please refer to the Radio Mode parameter in the MX7 Tecton Reference Guide. It is important that this parameter setting corresponds to the Access Point to which the MX7 Tecton connects.
-
Page 7: Setting Up Applock
Setting Up AppLock MX7 Tecton devices are shipped to boot in Administration mode. In this mode, the user has full access to the device and no password is needed. After the administrator completes the process below, the MX7 Tecton switches to end-user mode and restricts access to only the specified application(s). -
Page 8: Connecting Using Rfterm
Connecting Using RFTerm Before you make a host connection, you will, at a minimum, need to know: the alias name or IP address (Host Address) the port number (Telnet Port) of the host system to properly set up your host session. 1. - Page 9 8. Upon a successful connection, the host application screen is displayed. To change options (e.g., Display, Colors, Cursor, Barcode), please refer to the RFTerm Reference Guide for descriptions of these and other features.
-
Page 10: Rebooting The Mx7 Tecton
1. Using the Registry, select Start > Settings > Control Panel > Registry. 2. Tap the Warmboot button. When the MX7 Tecton is booting, there may be small delays while the wireless client connects, applications launch, remote management completes and Bluetooth... - Page 11 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
-
Page 12: Technical Assistance
Technical Assistance Contact information for technical support, product service, and repair can be found at www.honeywellaidc.com. Limited Warranty Refer to www.honeywellaidc.com/warranty_ information for your product’s warranty information. User Documentation To download the MX7 Tecton user documentation go to www.honeywellaidc.com.