Cisco 1600 series Quick Start Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 1600 series
  6. Quick start manual
Cisco 1600 series Quick Start Manual

Cisco 1600 series Quick Start Manual

Hide thumbs Also See for 1600 series:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual

Quick Start Guide

I
Y
C
1 6 0 5 R
N S TA L L I N G
O U R
I S C O
O U T E R
PC
Internet
PC
Ethernet
network 1
PC
PC
Ethernet
network 2
WAN
connection
Hub
PC
Hub
PC
Server
Cisco 1605
1
U
B
.
NPACK THE
OX
2
I
R
.
NSTALL THE
OUTER
3
V
Y
I
.
ERIFY
OUR
NSTALLATION

Advertisement

Table of Contents
loading

Related Manuals for Cisco 1600 series

Summary of Contents for Cisco 1600 series

  • Page 1: Quick Start Guide

    1 6 0 5 R N S TA L L I N G O U R I S C O O U T E R Internet Ethernet network 1 Ethernet network 2 connection Server Cisco 1605 NPACK THE NSTALL THE OUTER ERIFY NSTALLATION...

  • Page 2: Unpack The Box

    Unpack the Box. Note: The Cisco 1600 series routers are either of run-from-flash (RFF) or run-from-RAM (RFR) models. In this document, model names without an R refer to both models. The “Router Memory” section in the hardware installation guide that came with your router describes the differences between RFF and RFR models.

  • Page 3: Install The Router

    Install the Router. There are three steps to installing your router: Warning Hazardous network voltages are present in WAN interface card ports regardless of whether power to the router is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the router first.
  • Page 4 Install the Router (continued). A. Connect the router to the local networks. The router has three Ethernet ports, but supports only two Ethernet connections at one time. Connect the router to your local Ethernet networks in one of these ways: Option 1: Connect the ETHERNET Ø...
  • Page 5 Install the Router (continued). B. Install the WAN interface card. Look for a WAN interface card in the slot on the right-rear of the router, just above the slot labeled FLASH PC CARD. (There is no WAN interface card installed if there is a metal plate over the slot.) If the card is already installed, connect it to your WAN line according to the instructions that came with the card.

  • Page 6: Connect The Power Supply

    Install the Router (continued). C. Connect the power supply. After connecting the router to power and turning it on, you can confirm that you have installed the router correctly by checking certain LEDs. Connect the router to the power supply as shown below. Depending on where you are installing the router, your power supply and power outlet could be different from those in the picture.

  • Page 7: Verify Your Installation

    Cisco 1600 Series Software Configuration Guide that is in the accessory kit. • The Cisco Connection Online card that is in the accessory kit, which lists telephone numbers, e-mail addresses, and World Wide Web URLs for getting information directly from Cisco Systems.
  • Page 8 Venezuela AccessPath, Any to Any, AtmDirector, the CCIE logo, CD-PAC, Centri, the Cisco Capital logo, CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the Cisco Powered Network logo, the Cisco Press logo, the Cisco Technologies logo, ClickStart, ControlStream, DAGAZ, Fast Step, FireRunner, IGX, IOS, JumpStart, Kernel Proxy, LoopRunner, MGX, Natural Network Viewer, NetRanger, NetRanger Director, NetRanger Sensor, NetSonar, Packet, PIX, Point and Click Internetworking, Policy Builder, Precept, RouteStream, Secure Script, SMARTnet, SpeedRunner, Stratm, StreamView, The Cell, TrafficDirector,...

Table of Contents