Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for ViewSonic PD1012
- Page 1 PD1012 Pen Display User Guide Model No. VS15685...
- Page 2 Compliance Information Following information is only for EU-member states: The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law.
-
Page 3: Important Safety Instructions
Important Safety Instructions 1. DO NOT place objects on top of the device, as objects may scratch the screen. 2. DO NOT expose the device to dirty or dusty environments. 3. DO NOT place the device on an uneven or unstable surface. 4. -
Page 4: Declaration Of Rohs2 Compliance
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum... -
Page 5: Copyright Information
Copyright Information Copyright © ViewSonic Corporation, 2014. All rights reserved. ViewSonic and the three birds logo are registered trademarks of ViewSonic Corporation. Disclaimer: ViewSonic Corporation shall not be liable for technical or edito- rial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. -
Page 6: Table Of Contents
Contents Compliance Information............i Important Safety Instructions ............ ii Declaration of RoHS2 Compliance ......... iii Copyright Information ............. iv Product Registration ............... iv 1. Introduction ................1 1.1 Packing List ..................1 1.2 Product Overview ................1 2. Installation and Setup ............3 2.1 Installing the Driver ................ -
Page 7: Introduction
1. Introduction 1.1 Packing List After unpacking, make sure that all of the following contents are included: Pen Display Quick Start Guide Software CD Micro USB 3.0 Y-type Cable Mini USB 2.0 - USB Canle ... - Page 8 1.2.2 Rear View ⑤ Interactive pen holder strap ⑥ Stand (x2) ⑦ Kensington lock ⑧ Foot rubber (x4) ⑨ Rear label ⑩ Micro 3.0 Port: for signal input and power supply Caution: Avoid the risk of electric shock. Do not open the housing by yourself.
-
Page 9: Installation And Setup
2. Installation and Setup 2.1 Installing the Driver Use the included Micro USB 3.0 Y-type cable to connect the device to your desktop or notebook PC, as shown below. The screen will be off, but the red LED indicator light will turn on. Note: When connecting the device to a PC/NB, plug in both of the USB connectors to make sure there is sufficient power. - Page 10 2.1.2 Handwriting driver installation 1) Open the driver CD, and click on Pen Display xxx.exe to start installation on Windows. For installation on Mac OS, click Installxxx. dmg.
- Page 11 2) Click Install to begin the installation. 3) After complete the installation, you need restart your PC.
-
Page 12: Setting The Display Area
To access the setup window, click Start → Control Panel → Display → Adjust Resolution. 1) When installing your PD1012 device, you will also see additional options for configuring multiple displays. 2) There are 4 multiple display options to choose from: a. -
Page 13: Handwriting Area Mapping
2) Enter Mapping and set Select Monitor as Monitor 2. Note: 1. The pen’s accuracy has been fine-tuned during production. If needed, click Calibrate to adjust it manually. 2. When the desktop computer is connected to the PD1012 and general display, manually select the appropriate rotation for monitor 2. - Page 14 3) Use the pen display to draw inside the dialog box that is displayed on-screen to test and set the pressure sensitivity level. The sensitivity parameter can be adjusted by using the little wheel on the Try Here screen in Pen Setting interface. 4) Click Save then Exit to complete the setting procedure.
-
Page 15: More Touch Function Settings
2.4 More Touch Function Settings This section covers all of the built-in touch functions for Windows 7 and 8 operating systems. 2.4.1 Pen and Touch Click Start → Control Panel → Pen and Touch → Flicks tab. a. Pen Options: When using the stylus on the screen, you can adjust the movement and pen button settings. - Page 16 2.4.2 Tablet PC Settings Click Start → Control Panel → Tablet PC Settings → Other tab → Go to Input Panel Settings. These settings can be used to customize the following Tablet PC Input Panel features. Handwriting: Line width and writing spacing settings. ...
-
Page 17: Troubleshooting
3. Troubleshooting 3.1 Monitor problems Problems Suggested action No picture * Check USB cable should be completely connected to the computer and monitor. * Try another USB port of PC. * Check computer whether are in dormancy mode. Press keyboard or move the mouse to reactivate the system. * Press Screen power button to make sure the screen turned on. -
Page 18: Interactive Pen Problems
3.2 Interactive Pen Problems Problems Suggested action The pen is no * Try using mouse to double check, if mouse also no function function, please restarting your computer or your application. * Try to reinstall the driver. Pen tip is too * Check whether the pen tip is too short. -
Page 19: Product Specification
4. Product Specification 4.1 Monitor Display Type 10.1” TFT LCD, LED, Built-in interactive electromagnetic display modules Resolution 1280 x 800, 1024 x 768, 800 x 600, 640 x 480 @ 60 Hz Connector P1: Mini-B type for signal input (USB2.0) P2: Micro-B type for power input (5V/1.5A (Max) power adapter is recommended);... -
Page 20: Interactive Pen
4.2 Interactive Pen Type Electromagnetic resonance method Technology method Full screen Active area Technical Specs Resolution 5080LPI (line per inch) Tracking speed 220 PPS (points per second) Pressure sensitive 2048 levels Accuracy ± 0.5 mm (center), ± 2 mm (edge and corner) Height readable 10 mm Type... -
Page 21: Appendix
5. Appendix 5.1 Replacing a pen tip When the pen tip gets too short or develops a sharp edge, it can be replaced with spare tips. To replace a pen tip, follow the steps below: 1) Use a tool (such as needle-nose pliers) to pull the old tip straight out of the pen. -
Page 22: Customer Support
(Mexico) la/soporte/servicio-tecnico Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F. Tel: 55) 6547-6454 55)6547-6484 Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico C= http://www.viewsonic.com/ Latin America (Peru) www.viewsonic.com/la/ soporte@viewsonic.com la/soporte/servicio-tecnico Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com... -
Page 23: Limited Warranty
How long the warranty is effective: ViewSonic Pen Displays are warranted for 1 year for all parts and labor from the date of the first consumer purchase. Who the warranty protects: This warranty is valid only for the first consumer purchaser. - Page 24 Exclusion of damages: ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of...