Advertisement
6092-SS-CE IIR Manual
8/15/00
11:26 PM
Panic Mode
Press and hold button 3 on the remote control for at least 3 seconds. This will cause
the panel to go into a panic mode. Press button 1 (largest button) to disarm the panel.
Napco 1632, 3200 and 9600 panels must be programmed for keypad #2 panic
"ON" . SEE PAGE 7 for the Napco Program Guide.
If you are using a panel that does not have a default setting for keypad panic you
must program that option "ON" before our system will operate. Most manufacturers
set the keypad Panic as a default setting.
DEACTIVATING THE PANIC FEATURE:
In the event the user does not want to access a panic button through the remote
control, it can be de-activated from the Code Encryptor II's memory.
Step 1) Unplug the wire harness from the Code Encryptor II.
Step 2) Press and HOLD the program button.
Step 3) While HOLDING the program button, plug the Code Encryptor II harness
back in. The LED light located on the front will turn ON.
Step 4) Wait until the light turns "OFF".
Step 5) Once the light has turned "OFF" release the button
DEFAULT MODE:
• If the Code Encryptor II fails to recognize any of the data coming from the keypad
wires, it will automatically default to a relay mode for button #1
• If this happens, verify that you are properly wired to one of the alarms listed on
page 5.
• If you have connected the CE II to an alarm it does not recognize, follow the
wiring below for a keyswitch mode.
• Program a selected zone as "Keyswitch Arming."
• Do not use the green or yellow wires.
Installation for Keyswitch Arming
Red
Aux +
Black
Aux -
Brown/White Zone programmed for keyswitch arming
Brown
Common adjacent to zone
Black
Red
Alarm Panel
Zone programmed
Brown
for keyswitch arming
Resistor should be in-line OR across
the zone, whichever clears the zone.
Troubleshooting
PROBLEM: I press Button #1 (largest, button) but nothing happens.
SOLUTION: 1) Did you teach the Code Encryptor II a VALID four-digit user code?
Note: The code you teach the Code Encryptor II must be a master
code or one of the current user codes.
2) Press button #2 (middle button), if you do NOT hear a "click" at
the receiver, GO TO PAGE 14 and learn that remote into the Code
Encryptor II.
PROBLEM: I press and hold button #3 (smallest button) and I do not get a panic.
SOLUTION: 1) Did you program the panel for keypad panic?
2) To program the Code Encryptor II for panic GO TO PAGE 13.
PROBLEM: Unit does not seem to identify the panel I am using.
SOLUTION: Call technical 888-768-2846.
PROBLEM: I am using an FBI panel but the system won't operate.
SOLUTION: 1) Verify that NO KEYPADS are set to address #8.
2) Enter and exit programming to have the panel poll for keypads or
a CEII unit. (SEE PAGE 16 and 17)
PROBLEM: I an using a Napco 1632, 3200, 9600 or P816 and the remote will
not arm or disarm.
SOLUTION: 1) Verify that NO KEYPADS are set to address #2
2) Did you program Keypad #2 to Area #1 (SEE PAGE 7)
Street Smart Limited Warranty
Street Smart, a Division of Pittway Corporation, and it's divisions, subsidiaries and affiliates
("Seller"), 12925 Brook Printer Place, Suite 410 Poway, California 92064, warrants its products
to be in conformance with its own plans and specifications and to be free from defects in materi-
als and workmanship under normal use and service for 24 months from the date stamp control
on the product or, for products not having a Street Smart date stamp, for 12 months from date
of original purchase unless the installation instructions or catalog sets forth a shorter period, in
which case the shorter period shall apply. Seller's obligation shall be limited to repairing or
replacing, at it s option, free of charge for materials or labor, any product which is proved not in
compliance with Seller's specifications or proves defective in materials or workmanship under
normal use and service. Seller shall have not obligation under this Limited Warranty or other-
wise if the product is altered or improperly repaired or serviced by anyone other than Street
Smart factory service. For warranty service, return product transportation prepaid, to Street
Smart Factory Service, 12925 Brook Printer Place, Ste. 410, Poway, California 92064.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PAR-
TICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAM-
AGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER
BASIS OR LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN
NEGLIGENCE OR FAULT.
Seller does not represent that the products it sells may not be compromised or circumvented; that
the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise;
or that the products will in all cases provide adequate warning or protection. Customer understands
that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or
other events occurring without providing an alarm, but it is not insurance or a guarantee that such will
not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER
SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED
ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHERE
DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR
OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY
CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLU-
SIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only war-
ranty made by Seller or this product. No increase or alteration, written or verbal, of the obligations
of this Limited Warranty is authorized.
Page 2
Panic Continued
ACTIVATING THE PANIC MODE
NOTE: This is the default setting of the Code Encryptor II.
If you have previously programmed remote panic "OFF" and would like to turn it
back "ON" follow the steps below. If this is a NEW installation Panic "ON" is the
DEFAULT setting for the Code Encryptor II.
Step 1) Unplug the wire harness from the Code Encryptor II.
Step 2) Press and HOLD the program button.
Step 3) While HOLDING the program button, plug the Code Encryptor II harness
back in. The LED light located on the front will turn ON.
Step 4) Immediately release the program button.
IF NECESSARY, PROGRAM THE ALARM PANEL FOR KEYPAD PANIC.
12
Napco/Caddx Panels
• If a zone is programmed for "HOME/AWAY BYPASS" or AUTO-BYPASS", the alarm
will bypass that zone unless as "ENTRY/EXIT" zone is tripped after arming.
• If you wish to have a zone programmed as mentioned above, the CEII can be
installed to allow you to arm the panel in the "AWAY" mode from outside the house.
Step 1) Remove BOTH jumpers from the CEII control module. They are located
next to the wire harness
Step 2) Connect the Channel 3 wires to the zone programmed for "ENTRY/EXIT".
When armed with the CEII remote, the relay will energize for 1 second,
causing the zone to be tripped and arm the alarm in the "AWAY" mode.
Alarm Panel
Zone programmed
as an entry/exit
CODE
Channel 3 wires offer N/O and N/C contacts.
ENCRYPTOR
Utilize the wires to open or close the zone based on your installation.
Brown/White
FBI Addressable Keypads
• When using an addressable keypad like an XK-7LC, XK-5LC, XK-508, XK-512, XK-
516, XK-708, XK-716 you may have to complete an extra step before the CEII will
operate. SEE PAGE 17.
15
Specifications
RECEIVER
• 12VDC Power Input
• Channels 1 Data outputs
• Channel 2 Relay N/O, Comm (10amp)
• Channel 3 selectable: Form C Relay (N/O, N/C, Comm) 5amp
This output can be reconfigured from a pulsed output to a latching, 75 second
timed or 150 second timed output.
• Channel 3 - Keypad panic data output (Programmable On or OFF)
Frequency 303Mhz
Stand by Power Consumption 15ma
Temperature Range -5°F to 160°F (Indoor use only)
REMOTE CONTROL
Battery 12VDC Mini (Part #GP23A) Replace battery at least once a year.
Range 150+ feet
CHANNEL 3 OUTPUT
Both jumpers in (default)
Jumper closest to the harness removed
Jumper farthest from the harness removed
Both jumpers out
STREET SMART SECURITY TECHNICAL CAN BE REACHED AT:
12925 Brook Printer Place, Suite 410, Poway, CA 92064
M-F 7AM-5PM PST AT (888) 768-2846 OR (619) 513-9352-FAX
18
Federal Communications Commission
(FCC) Statement
This equipment has been tested to FCC requirements and has been found acceptable for use.
The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used
properly, that is, in strict accordance with the manufacturer's instructions, may cause interfer-
ence to radio and television reception. It has been type tested and found to comply with the
limits for a Class B computing device in accordance with the specifications in Part 15 of FCC
Rules, which are designed to provide reasonable protection against such interference in a resi-
dential installation. However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause interferences to radio or television reception ,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated
• Move the receiver away from the control/communicator.
• Move the antenna leads away from any wire runs to the control/communicator.
• Plug the control/communicator into a different outlet so that it and the receiver are on
different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television
technician for additional suggestions.
The user or installer may find the following booklets prepared by the Federal
Communications Commission helpful: "Interference Handbook"
This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by
the installation instructions or User's Manual. Unauthorized changes or modifications could
void the user's authority to operate the equipment.
21
To Add or Delete Remotes
TO ADD A NEW REMOTE
METHOD #1
To add a remote to your Code Encryptor II, disarm the panel and Enter 78738,
(if using a Napco 1632, 3200 or 9600 press the ON/OFF to send the data.) from
the keypad. The system will arm in the "STAY" mode. Press and release button #1
(largest button on the remote control) until the arm system disarms. It should take a
total of four presses.
METHOD #2
To add a remote to your Code Encryptor II PRESS AND RELEASE the program
button on the receiver. The light on the receiver will come ON. Immediately PRESS
button 1 (largest button) on the new remote control THREE TIMES. The light on
the receiver should go OFF, indicating the remote has been learned. If the light on
the receiver stays ON, the remote has not been learned. Remove and replace the
harness, wait 15 seconds while auto recognition occurs and follow these instructions
again.
13
FBI Addressable Continued
• These FBI panels poll for addressable or non addressable keypads upon power up
OR after you exit programming. Since the CEII requires that you plug it in after the
FBI is powered up, it misses that polling loop.
TO have the FBI panel Re-Poll for keypads and CEII units
Step 1) Enter Programming Mode: Press "CODE" + "*" and installers code (2468
default) followed by a "1".
Step 2) Exit Programming by pressing the "STAY" key.
Step 3) The CEII will enroll itself as an Addressable Keypad at address #8
To Delete ALL Remotes
Black
Red
METHOD #1
To delete a lost or stolen remote from the Code Encryptor II, you must purge the
entire memory. This will delete all of the current remotes. You will then have to add
CODE
them back in one at a time. To purge the memory, disarm the panel. Enter
ENCRYPTOR
76278, (if using a Napco 1632, 3200 or 9600 press the ON/OFF to send the
data), from the keypad. The keypad on most panels will "beep" or the lights will
Brown
Brown/White
turn off momentarily to confirm delete. Follow the instructions on page 14 (To Add
a New Remote).
METHOD #2
To delete a lost or stolen remote from the Code Encryptor II, you must purge the
entire memory. This will delete all of the current remotes. You will then have to add
them back into memory. To purge, PRESS AND HOLD the program button, the
light will come ON for four seconds, then go OFF, and finally it will come ON again,
indicating that all the remotes in memory have been purged. Release the program
button and follow the instructions on page 14 (To Add a New Remote).
16
Optional Reversible Outputs
Channel 2 has two independent outputs that occur when button #2 is pressed. The
first output is a momentary relay contact closure which is intended for the use of
opening and closing a garage door. This is the primary output and can not be
changed or reconfigured. The second output is a (-) 500ma transistor output to
provide a zone bypass or illuminated entry/exit.
• If you are not using the relay for Channel 3 you may choose to swap the
(-) transistor output for the relay. In this instance you will then have two contact
closures every time Button # 2 is pressed. The standard momentary contact
closure and ALSO a Form C relay that will energize automatically for 3 minutes
every time the garage door is opened or closed.
To Swap the transistor and relay outputs.
Step 1) While watching the LED on the CE II receiver press and HOLD button 1 and
Step 2) To make channel 2 a relay press the program button on the CE II Receiver
Momentary output
Latching (on/off) output
Step 3) Wait 10 seconds and the CE II will automatically reconfigure the outputs.
75sec timed output
150sec timed output (not
NOTE- Even if you swap outputs, the Panic button will still operate if
applicable if using the feature
you press and HOLD button #3 for three seconds.
on page 16)
19
Canadian Department of
Communications (DOC) Statement
NOTICE: The Canadian Department of Communications label identifies certified
equipment. This certification means that the equipment meets certain
telecommunications network protective, operational and safety requirements. The
Department does not guarantee the equipment will operate to the user's satisfaction .
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The equipment
must also be installed using an acceptable method of connection. In some cases, the
company's inside wiring associated with a single line individual service may be
extended by means of certified connector assembly (telephone extension cord). The
customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designed by the supplier. Any repairs or alterations made by the
user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections
of the power utility, telephone lines and internal metallic water pipe system, if pre-
sent, are connected together. This precaution may be particularly important to rural
areas.
CAUTION: User should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes he percentage of
the total load to be connected to a telephone loop which is used by the device, to
prevent overloading. The termination on a loop may consist of any combination of
devices subject only to the requirement that the total of the Load Numbers of all the
devices does not exceed 100.
22
The Code Encryptor II can hold up to seven remotes.
3 simultaneously on the remote control until the LED on the CE II receiver
illuminates. (approx. 5 seconds)
TWICE, to make it a transistor output press ONCE (Default setting)
IMPORTANT
This feature will not work for NAPCO/CADDX
if you are using the feature on page 16.
14
17
20
23
Advertisement
