Hitachi P 20SB Handling Instructions Manual
Hide thumbs
Also See for P 20SB:
- Instruction manual (48 pages) ,
- Handling instructions manual (28 pages) ,
- Instruction manual and safety instructions (17 pages)
Advertisement
Quick Links
Planer
Model P 20SB
Handling instructions
Note:
Before using this Electric Power Tool, carefully read through these
HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available
as an important reference when using this power tool.
Advertisement
Related Manuals for Hitachi P 20SB
Summary of Contents for Hitachi P 20SB
- Page 1 Planer Model P 20SB Handling instructions Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this power tool.
-
Page 2: General Safety Rules
d) Remove any adjusting key or wrench before GENERAL SAFETY RULES turning the power tool on. A wrench or a key left attached to a rotating part WARNING! of the power tool may result in personal injury. Read all instructions e) Do not overreach. -
Page 3: Specifications
PRECAUTION PRECAUTIONS ON USING PLANER Keep children and infirm persons away. When not in use, tools should be stored out of Do not use the Planer with the blades facing upward reach of children and infirm persons. (as stationary type planer). Use dust collection adapter if need to reduce dust Planer Safety Rules related hazards. - Page 4 Knob 4. Precaution after finishing the planing operation: When the planer is suspended with one hand after finishing the planing operation, ensure that the cutting blades (base) of the planer do not contact or come too near your body. Failure to do so could result in serious injury.
- Page 5 2. Cutter blade assembly: (3) Turn the cutter block over, and set the other side in the same manner. CAUTIONS Prior to assembly, thoroughly wipe off all swarf 3. Adjustment of cutter blade height: accumulated on the cutter blade. CAUTION (1) Turn the flat surface of the cutter block sideways, As the set gauge has been accurately factory and assemble the adjusted cutter blade as shown...
- Page 6 (4) Finally, retighten the machine screw to securely CAUTION fasten the cutter blade and the back metal, thereby Be careful not to injure your hands. completing the blade height adjustment procedure. 2. Carbide blade assembly: (5) Holding the set gauge as shown in Fig. 14, push CAUTION upward on the back metal and remove it from the Prior to assembly, thoroughly wipe off all swarf...
- Page 7 3. Adjustment of carbide blade height: (5) As shown in Fig. 23, 24, insert a turned portion of CAUTION set plate (A) attached to set plate (B) into a groove If the carbide blade’s heights are inaccurate after on the flat portion of the cutter block. above procedures have been completed, carry out the procedures described below.
- Page 8 Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. Fig. 28 7. Replacing supply cord If the supply cord of Tool is damaged, the Tool must be returned to Hitachi Authorized Service Center for the cord to be replaced.
- Page 9 C: No. Used D: Remarks CAUTION Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.
- Page 11 958731Z 984750 D4×16 958732Z 937631 990669 M8×18 47-1 930487 D8.2 958734Z 47-2 930026 D10.2 _______ 986723 M4×8 958733Z 957747 958728 959140 958730Z “1, 2, 9, 21” 958944 6200VV 6200VVCMPS2L 940633 958709 954004 D4×16 958708 994273 958707 980063 958945 930153 954004 D4×16 985191 958710...
- Page 12 Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99034111 F Printed in China...