Table of Contents
Related Manuals for K&F SONA SUB II
Summary of Contents for K&F SONA SUB II
- Page 1 K&F SONA SUB II Version 1.3 User's Manual Released: 25.06.2014 Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße 14 D-30179 Hannover TEL +49 (0) 511 96 99 70 FAX +49 (0) 511 67 37 94 www.kling-freitag.de...
-
Page 3: Table Of Contents
Correct Ratio between Top and Bass Speakers Level increase because of adjacent areas Configuration and Connecting Diagram Terminal assignment SONA SUB II with SONA top and systemrack SONA SUB II with SONA top, unfiltered SONA SUB II "XO" with SONA top Wiring... -
Page 4: Introduction
Thank you for your decision to buy a KLING & FREITAG product. To guarantee a trouble- free operating of the equipment and to allow your KLING & FREITAG SONA SUB II system to achieve its full potential please read the operating instructions carefully before use. With the purchase of a SONA SUB II, you have acquired a large sound system with the highest possible quality and performance capabilities. -
Page 5: Product Description
K&F SONA SUB II Product Description The subwoofer SONA SUB II is the ideal bass supplement for K&F SONA speakers. With its discreet appearance, it fits in nearly any architecture. The practical mounting points with a double keyhole design enable wall and ceiling installation. In addition to possible use with the K&F Controller CD 44, it can also be operated with a universal electronic crossover. -
Page 6: Required Signal Processor
Required signal processor The following information does not apply to the option "XO" : When using the SONA SUB II, a signal processor is required such as an electronic crossover or the K&F Controller CD 44. The signal processor must provide at least the following settings: •... -
Page 7: Preventing Hearing Damage
Configuration and Connecting Diagram from page 10. Operations with CD 44 Controller: • For optimal performance and operating safety of the SONA SUB II speakers we recommend using the system controller K&F CD 44. • When operating the loudspeaker with amplifers without clipping limiter and nominal amplifier power less than 75W@8Ohm requires to set a Limit Reduction of 3dB for the K&F CD 44 controller. - Page 8 User's manual K&F SONA SUB II • where the devices are exposed to high moisture or rain. • where the devices are exposed to strong vibrations and dust. Avoid damage caused by the speakers' magnetic fields Speakers are permanently surrounded by a magnetic field, even when they are not connected.
-
Page 9: Correct Ratio Between Top And Bass Speakers
For a balanced sound reproduction, suitable for speech and average music material, one subwoofer SONA SUB II can be combined with up to 4 tops SONA 5. This is valid as long as the amplifiers for subwoofer and top skeakers have the same overall gain and the SONA SUB II is mounted on a wall or on the open floor (reference use). -
Page 10: Configuration And Connecting Diagram
User's manual K&F SONA SUB II Configuration and Connecting Diagram Terminal assignment In 1 In 2 • Without the option "XO" the second phoenix output is parallel to the first phoenix output. • At the "XO" option the second phoenix output is for top speakers. -
Page 11: Sona Sub Ii With Sona Top And Systemrack
In the CD 44, choose the LSBlock 'Sona 6 LCut' for the speaker SONA 6. SONA SUB II: In the CD 44, choose the LS-Block 'Sona Sub II' for the speaker SONA SUB II. KLING & FREITAG GMBH © 2014 Version 1.3... -
Page 12: Sona Sub Ii "Xo" With Sona Top
User's manual K&F SONA SUB II SONA SUB II with SONA top, unfiltered connection diagram SONA 6 SONA 6 STEREO SONA 5 SONA 5 SONA 5 SONA 5 STEREO SONA 8 MONO SONA SUB II Amplifier Amplifier Signal Processor Signal Processor... - Page 13 User's manual K&F SONA SUB II SONA SUB II "XO" with SONA top connection SONA 5 or SONA 6 SONA 6 SONA 6 STEREO SONA 5 SONA 5 SONA 5 SONA 5 STEREO STEREO SONA SUB II Option "XO" Amplifier...
-
Page 14: Wiring
Speakon connector. Without the Phoenix plug, the Phoenix connector’s contacts have hazardous contact voltage! Wiring instructions • Before connecting your SONA SUB II loudspeaker switch off all equipment and turn down all level controls. • Only use high-quality speaker cables with a sufficient wire gauge. The wire gauge depends on the length of the speaker cable. - Page 15 User's manual K&F SONA SUB II • Switch on the mixing console first, then the controller and the power amplifier. Always use the before mentioned switching order. Otherwise switching noises may damage the sound system. • If there is interference, turn off all appliances in the reverse order and check all cable connections.
-
Page 16: Technical Specifications
User's manual K&F SONA SUB II Technical Specifications Design Bass reflex system (Operations via K&F SystemRack) Frequency range without filter 70 Hz - 400 Hz (+/-3 dB / -10 dB) 60 Hz - 450 Hz Frequency range with Filter 42 Hz / 32 Hz (half space) -
Page 17: Measuring Diagrams
User's manual K&F SONA SUB II Measuring Diagrams Frequency response Frequency response Option XO Impedance 1000 Frequency (Hz) KLING & FREITAG GMBH © 2014 Version 1.3 Page 17 of 19... -
Page 18: 10. Dimensions
User's manual K&F SONA SUB II 10. Dimensions Weight: 16.9 kg 485,0 mm / 19,094" 308,0 mm / 12,126" KLING & FREITAG GMBH © 2014 Version 1.3 Page 18 of 19... -
Page 19: 11. Disposal
User's manual K&F SONA SUB II 11. Disposal 11.1 Regulations for Disposal 11.1.1 Germany It is not allowed to dispose of used electrical equipment as domestic waste. Dispose of the device at public collection points for recycling! The device is a so called dual-use product intended for domestic and commercial use.