Panasonic PHI/TY-LA1000 User Instructions

P P H H I I / / T T Y Y - - L L A A 1 1 0 0 0 0 0 0
R R L L
E E P P L L A A C C E E M M E E N N T T A A M M P P F F O O R R
U I
SER NSTRUCTIONS
.
CAUTION:
.
Do not attempt to remove the lamp immediately after use; doing so can cause serious burns. Prior to removing lamp, switch off the
power supply to the television and wait approximately 60 minutes or more to allow for complete lamp cooling.
.
Avoid touching the glass portion(s) of the lamp with bare hands; fingerprints, dirt and dust may cause early lamp failure and/or image
obscurity. It is recommended that gloves be worn when replacing the lamp.
When transporting the replacement lamp, use the box that is provided to avoid breakage.
.
WARNING:
.
To avoid overheating and/or fire, ensure that the replacement lamp is mounted securely.
Hg - LAMP CONTAINS MERCURY, Manage in Accord with Disposal Laws. See: www.lamprecycle.org or
1-800-555-0050.
R L
EPLACING THE AMP
MODELS PT -50LC13/PT -60LC13/PT -50LCX63/PT -60LCX63/PT -43LCX64/
PT -50LCX64/PT -60LCX64/PT -43LC14/PT -50LC14/PT -60LC14
1
LAMP indicator
Switch off power to the television, wait until the power
indicator stops blinking red, then unplug the power cord from
the wall outlet. Allow the television to cool for at least
1 hour.
[If the lamp must be replaced more urgently:]
The projection display has a feature for forced cooling.
During the first minute of the normal cooling fan operation
after the POWER button is turned OFF, press the VOL+
button on the projection display and the s button on the
remote control simultaneously for more than 5 seconds.
The cooling fan will operate for approximately 10 minutes.
The LAMP indicator will flash red 5 times every 5 seconds.
2
Front cover
Remove the front cover by placing your fingertips under the
front cover and pulling it from the projection display.
R L
ESETTING THE AMP
MODELS PT -50LC13/PT -60LC13/PT -50LCX63/PT -60LCX63/PT -43LCX64/PT -50LCX64/PT -60LCX64/PT -43LC14/PT -50LC14/PT -60LC14
W : Only reset the lamp timer when the lamp has been replaced.
1
ARNING
Plug the power cord back into a properly grounded wall outlet. Then press the POWER button on the projection
display or the remote control to turn the power on.
2
+
UNIT
_ VOL
While pressing the VOL- button on the projection display, hold down the PIP or SPLIT button on the remote control
simultaneously for more than 5 seconds.
3
When the lamp time reset procedure is complete, the above screen will appear. (This screen may be different from
the actual screen.) Note: When the lamp time reset is complete, the LAMP indicator goes out.
P P L L C C D D R R
A A N N A A S S O O N N I I C C
®
POWER button/
POWER indicator
T
IMER
REMOTE CONTROL
For models PT-50LC13/PT-60LC13/PT-50LCX63/
PT-60LCX63/PT-43LCX64/PT-50LCX64/PT-60LCX54
P P T T
E E A A R R R R O O J J E E C C T T I I O O N N E E L L E E V V I I S S I I O O N N
3
After reading the caution and warning labels on the lamp
cover, loosen the lamp cover screw using a screwdriver. 4
Lamp Unit
Handle
Using a screwdriver, loosen the lamp unit screw. Grasp
the lamp unit handle and slowly pull the lamp unit from the
projection display.
5
Insert the new lamp unit, paying attention to the direction of
insertion. Press on the lamp unit handle, ensuring that the
insertion is done correctly. Dispose of the old lamp in accor-
dance with disposal laws. Tighten the lamp unit screw and the
lamp cover screw using a screwdriver. Replace front cover.
[Note: Ensure that the lamp unit and lamp unit housing
doors are attached securely. If not, the protective circuit will
be activated and the power will not turn on.]
PIP
LAMP TIME WAS
RESET TO 0.
SPLIT
For models PT-43LC14/PT-50LC14/PT-60LC14
PLAY
OR
Lamp Unit
Screw