Table of Contents
Advertisement
Quick Links
Thank you for purchasing this Panasonic Product.
■ This manual is intended for products manufactured from Apr. 2015 and beyond.
■ Before operating this product, please read the instructions carefully, and save this manual
for future use.
■ Before using your projector, be sure to read "Read this first!" (x pages 2 to 9).
Operating Instructions
LCD Projector
Model No.
Functional Manual
Commercial Use
PT-LW330
PT-LW280
PT-LB360
PT-LB330
PT-LB300
PT-LB280
ENGLISH
TQBJ0693-4
Advertisement
Table of Contents
Related Manuals for Panasonic PJLink PT-LW330
Summary of Contents for Panasonic PJLink PT-LW330
-
Page 1: Operating Instructions
PT-LB330 PT-LB300 PT-LB280 Thank you for purchasing this Panasonic Product. ■ This manual is intended for products manufactured from Apr. 2015 and beyond. ■ Before operating this product, please read the instructions carefully, and save this manual for future use. -
Page 2: Read This First
This is a device to project images onto a screen, etc., and is not intended for use as indoor lighting in a domestic environment. Directive 2009/125/EC Importer's name and address within the European Union Panasonic Marketing Europe GmbH Panasonic Testing Center Winsbergring 15, 22525 Hamburg, Germany 2 - ENGLISH... - Page 3 FCC NOTICE (USA) Declaration of Conformity Model Number: PT-LW330 / PT-LW280 / PT-LB360 / PT-LB330 / PT-LB300 / PT-LB280 Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America Address: Two Riverfront Plaza, Newark, NJ 07102-5490 General Contact: http://www.panasonic.com/support Projector Contact: http://www.panasonic.net/avc/projector/...
- Page 4 Read this first! IMPORTANT: THE MOULDED PLUG (U.K. only) FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug.
- Page 5 Read this first! WARNING: „ POWER The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily acces- sible when problems occur. If the following problems occur, cut off the power supply immediately. Continued use of the projector in these conditions will result in fire or electric shock. z If foreign objects or water get inside the projector, cut off the power supply.
- Page 6 If liquid enters inside of the projector, consult your dealer. z Particular attention must be paid to children. Use the ceiling mount bracket specified by Panasonic. Defects in the ceiling mount bracket will result in falling accidents. z Attach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down.
- Page 7 Read this first! WARNING: Do not disassemble the lamp unit. If the lamp breaks, it could cause injury. Lamp replacement The lamp has high internal pressure. If improperly handled, an explosion and severe injury or accidents will result. z The lamp can easily explode if struck against hard objects or dropped. z Before replacing the lamp, be sure to disconnect the power plug from the wall outlet.
- Page 8 Read this first! CAUTION: „ MAINTENANCE Ask your dealer about cleaning inside the projector once a year. Continuous use while dust is accumulated inside the projector may result in fire. z For cleaning fee, ask your dealer. Brazil Only Brasil Apenas „...
- Page 9 As for the terms and conditions, please refer to the soft- ware license of the supplied CD-ROM. If you wish to ask any questions as to the software, please contact (sav.pj.gpl.pavc@ml.jp.panasonic.com) by email. r Illustrations in these operating instructions f Illustrations of the projector, screen, and other parts may vary from the actual product.
-
Page 10: Features Of The Projector
Features of the Projector Quick Steps For details, see the corresponding pages. Comfortable viewing in a bright environment 1. Set up your projector. (x page 25) The high contrast ratio 10 000 : 1 is achieved in a compact body. The low noise level 28 dB supports comfortable viewing during quiet scenes. -
Page 11: Table Of Contents
Contents Contents Contents Be sure to read “Read this first!” from page 2. Read this first! ..........2 Using the presentation timer function ....40 Switching the lamp power ........40 Using the digital zoom function ......41 Chapter 1 Preparation Controlling the volume of the speaker .... - Page 12 Contents [Logo] ..............64 [Security] .............. 66 [Power management] ........... 67 [Filter counter] ............68 [Test pattern] ............68 [Network] .............. 69 [Remote control] ........... 70 [Factory default] ............ 70 [Memory Viewer] menu ........... 71 [Set Slide] ............. 71 [Slide Transition Effect] ......... 71 [Sort Order] ............
-
Page 13: Chapter 1 Preparation
Preparation Chapter 1 This chapter describes things you need to know or check before using the projector. ENGLISH - 13... -
Page 14: Precautions For Use
Chapter 1 Preparation - Precautions for use Precautions for use Cautions when transporting f When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. Doing so may damage the internal parts and result in malfunctions. f Do not transport the projector with the adjustable foot extended. -
Page 15: Security
Make your password as difficult to guess as possible. f Change your password periodically. f Panasonic or its affiliate company never inquires a password directly to a customer. Do not tell your password in case you receive such an inquiry. -
Page 16: Cautions On Use
Chapter 1 Preparation - Precautions for use Cautions on use rTo get a good picture quality f Draw curtains or blinds over windows and turn off any lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. f Depending on where the projector is used, heated air from an exhaust port or warm or cold air from an air conditioner can cause a shimmering effect on screen. -
Page 17: Accessories
Chapter 1 Preparation - Precautions for use Accessories Make sure the following accessories are provided with your projector. Numbers enclosed < > show the number of accessories. Wireless remote control unit <1> CD-ROM <1> (N2QAYA000110) (TXFQB02VLP8) Power cord AAA/R03 or AAA/LR03 battery <2> (K2CG3YY00184) (for remote control unit) (K2CT3YY00079) -
Page 18: Contents Of The Supplied Cd-Rom
Chapter 1 Preparation - Precautions for use Contents of the supplied CD-ROM The contents of the supplied CD-ROM are as follow. Operating Instructions – Functional Manual Operating Instructions – Multi Projector Monitoring & Control Software This is a list of projectors that are com- patible with the Multi Projector Monitor- List of Compatible Projector Models Instruction/list (PDF) -
Page 19: About Your Projector
Chapter 1 Preparation - About your projector About your projector Remote control 12 <VOLUME +/–> buttons 1 Power <v/b> button Adjusts the volume of the built-in speaker or audio Turns the projector on or off. output. (x page 41) 2 <COMPUTER 1> button Switches the Computer 1 or Component signal to project. -
Page 20: Projector Body
Chapter 1 Preparation - About your projector Note f The remote control can be used within a distance of about 5 m (16'4-13/16") if pointed directly at the remote control signal receiver. The remote control can control at angles of up to ± 30 ° vertically and ± 30 ° horizontally, but the effective control range may be reduced. -
Page 21: Control Panel And Indicators
Chapter 1 Preparation - About your projector 9 Projection Lens 12 Security slot This security slot is compatible with the Kensington 10 Air exhaust port security cables. 11 <AC IN> terminal 13 Rear terminals Connect the supplied power cord. 14 Speaker Attention f Do not block the ventilation ports (intake and exhaust) of the projector. - Page 22 Chapter 1 Preparation - About your projector 3 <COMPUTER 1 IN> terminal 9 <AUDIO IN 1> terminal This is the terminal to input RGB, YP This is the terminal to input computer audio signals. S-video signals. In addition, if you have set [HDMI setup] → [Sound] to [Computer], it outputs the analog audio of the input 4 <COMPUTER 2 IN/ 1 OUT>...
-
Page 23: Using The Remote Control
Chapter 1 Preparation - Using the remote control Using the remote control Inserting and Removing batteries Fig. 1 Fig. 2 Open the cover. (Fig. 1) Insert batteries and close the cover (Insert the "m" side first.). (Fig. 2) f When removing the batteries, perform the steps in reverse order. Setting Remote control ID numbers When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single remote control, if unique ID number is assigned to each projector. -
Page 24: Chapter 2 Getting Started
Getting Started Chapter 2 This chapter describes things you need to do before using the projector such as the setup and connections. 24 - ENGLISH... -
Page 25: Setting Up
Chapter 2 Getting Started - Setting up Setting up Installation mode There are four ways to set up the projector. Set the [Display] menu → [Project way] (x page 51) depending on the installation location. Mounting on the ceiling and projecting forward Setting on a desk/floor and projecting from rear (Using the translucent screen) Menu item... -
Page 26: Screen Size And Throw Distance
Chapter 2 Getting Started - Setting up Screen size and throw distance Refer to the screen size and projection distances to install the projector. Image size and image position can be adjusted in accordance with the screen size and screen position. Projected image Screen L (LW/LT) - Page 27 Chapter 2 Getting Started - Setting up For PT-LW280 All measurements below are approximate and may differ slightly from the actual measurements. (Unit: m) Projection 4:3 aspect ratio 16:9 aspect ratio 16:10 aspect ratio size Minimum Maximum Minimum Maximum Minimum Maximum Screen Height...
- Page 28 Chapter 2 Getting Started - Setting up Projection size 4:3 aspect ratio 16:9 aspect ratio Minimum Maximum Minimum Maximum distance distance distance distance Screen diagonal (SD) Height position (H) Height position (H) (LW) (LT) (LW) (LT) 0.76 (30") 0.065 0.008 1.02 (40") 0.087 0.011...
-
Page 29: Adjusting Adjustable Foot
Chapter 2 Getting Started - Setting up Adjusting adjustable foot Lift the front of the projector and press the foot lock latch with your finger to adjust the projection angle up and down. Release your finger to lock the adjustable foot. For slight adjustment, rotate the adjustable foot. -
Page 30: Connecting
Chapter 2 Getting Started - Connecting Connecting Before connecting f Before connecting, carefully read the operating instructions for the external device to be connected. f Turn off the power switch of the devices before connecting cables. f Take note of the following points before connecting the cables. Failure to do so may result in malfunctions. - When connecting a cable to a device connected to the projector or the projector itself, touch any nearby metallic objects to eliminate static electricity from your body before performing work. -
Page 31: Connecting Example : Av Equipment
Chapter 2 Getting Started - Connecting <HDMI IN> terminal pin assignments and signal names Outside view Pin No. Signal names Pin No. Signal names T.M.D.S clock shield T.M.D.S data 2+ T.M.D.S clock - T.M.D.S data 2 shield Even-numbered pins T.M.D.S data 2 - —... - Page 32 Chapter 2 Getting Started - Connecting r For PT-LW330, PT-LW280, PT-LB360 and PT-LB330 Computer Computer Computer Computer USB memory Control computer Control computer Audio equipment r For PT-LB300 and PT-LB280 Computer Computer Computer Control computer Control computer Audio equipment Attention f When connecting the projector to a computer or an external device, use the power cord supplied with each device and commercially available shielded cables.
-
Page 33: Chapter 3 Basic Operations
Basic Operations Chapter 3 This chapter describes basic operations to start with. ENGLISH - 33... -
Page 34: Powering On/Off
Chapter 3 Basic Operations - Powering on/off Powering on/off Connecting the power cord Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily. For details of power cord handling, refer to “Read this first!” (x page 2). Attaching Check the shapes of the <AC IN>... -
Page 35: Powering On The Projector
Chapter 3 Basic Operations - Powering on/off Powering On the Projector Æ Before switching on the projector, make sure all the other devices are correctly connected. ( pages 30 - 32) Connect the power cord to the projector body. Connect the power plug to an outlet. f The power indicator <ON(G)/STANDBY(R)>... -
Page 36: Making Adjustments And Selections
Chapter 3 Basic Operations - Powering on/off Making adjustments and selections It is recommended that images are projected continuously for at least 30 minutes before the focus is adjusted. Adjust the focus of the image roughly. (x page 37) Change the settings of the [Display] menu → [Project way] depending on the installation mode. (x page 51) f Refer to “Navigating through the menu”... -
Page 37: Projecting
Chapter 3 Basic Operations - Projecting Projecting Check the connections of the peripheral devices ( Æ pages 30 - 32) and connection of the power cord (x page 34) and switch on the power (x page 35) to start the projector. Select the image and adjust the state of the image. Selecting the input signal Select an input signal. -
Page 38: Basic Operations By Using The Remote Control
Chapter 3 Basic Operations - Basic operations by using the remote control Basic operations by using the remote control Using the automatic setup function Input search, Auto PC adjustment (during signal input from a computer) and Auto Keystone correction works at the same time. The Auto PC adjustment function can be used to automatically adjust the resolution, clock phase, and image position when analog RGB signals consisting of bitmap images such as computer signals are being input. -
Page 39: Switching The Aspect Ratio Of The Image
Chapter 3 Basic Operations - Basic operations by using the remote control Note f For more details about Memory Viewer function, refer to “Memory Viewer function” (x page 79). f For more details about USB Display function, refer to “USB Display function” (x page 81). Switching the aspect ratio of the image You can switch aspect ratios according to the input signal. -
Page 40: Using The Information Function
Chapter 3 Basic Operations - Basic operations by using the remote control Using the information function This function allows you to display the status of the projector. button Press the <INFO.> button on the remote control. f The [Info.] screen is displayed. f When the [Info.] screen is recalled by using <INFO.>... -
Page 41: Using The Digital Zoom Function
Chapter 3 Basic Operations - Basic operations by using the remote control button Press the <LAMP> button on the remote control. f It will switch each time you press the button, [ (Normal)] → [ (Eco 1)] →[ (Eco 2)]. Note f For details, please refer to the [Setting] menu →... -
Page 42: Using The Mute Function
Chapter 3 Basic Operations - Basic operations by using the remote control Using the mute function This button allows you to turn off the audio output temporarily. button Press the <MUTE> button on the remote control. f The audio turns off. Press the <MUTE>... -
Page 43: Chapter 4 Settings
Settings Chapter 4 This chapter describes the settings and adjustments you can make using the on-screen menu. ENGLISH - 43... -
Page 44: Menu Navigation
Chapter 4 Settings - Menu Navigation Menu Navigation The on-screen menu (Menu) is used to perform various settings and adjustments of the projector. Navigating through the menu Operating procedure button Press the <MENU> button on the remote control or the control panel. f The main menu screen appears. -
Page 45: Main Menu
Chapter 4 Settings - Menu Navigation Press as to switch or adjust settings. f Some items will switch in order as follows each time you press Press the <ENTER> button or the <MENU> button. f The changed settings or the adjusted value is confirmed. Press as to select a sub-menu item, press the <ENTER>... -
Page 46: Sub-Menu
Chapter 4 Settings - Menu Navigation Sub-menu The sub-menu screen of the selected main menu appears, and you can set and adjust the various items in the submenu. [Display] Sub-menu item Factory default Page [Auto PC adj.] [Fine sync] [H Position] [V Position] [H.Size] [Aspect]... - Page 47 Chapter 4 Settings - Menu Navigation Sub-menu item Factory default Page [Auto setup] [Keystone] [Store] [Logo] [Security] [Power management] [Shut down] [Filter counter] [Test pattern] [Off] [Network] [Remote control] [All] [Factory default] [Memory Viewer] Sub-menu item Factory default Page [Set Slide] [Slide Transition Effect] [Slide Right] [Sort Order]...
-
Page 48: [Input] Menu
Chapter 4 Settings - [Input] menu [Input] menu To select the input source directly by pressing the input selection buttons on the remote control or to select the input source in the [Input] screen by pressing the <INPUT/ENTER> button on the control panel. Switching the input source When using the remote control Press the input selection (<COMPUTER 1>, <COMPUTER 2>, <HDMI>, <VIDEO>, <MEMORY VIEWER/... -
Page 49: [Display] Menu
Chapter 4 Settings - [Display] menu [Display] menu On the menu screen, select [Display] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fAfter selecting the item, press as to set. -
Page 50: [V Position]
Chapter 4 Settings - [Display] menu Orientation Operation Adjustment Press the a button. The image position moves to the right. Horizontal (left and right) adjustment. Press the s button. The image position moves to the left. Note f [H Position] is not available while the image is expanded in the digital zoom function. [V Position] (Only for computer signals input) Move the image position vertically if the image position projected on the screen is shifted even when the relative position of the... -
Page 51: [Project Way]
Chapter 4 Settings - [Display] menu [Project way] Set the projection method in accordance with the installation status of the projector. Change the projection method if the screen display is upside down or inverted. Press as to select [Project way]. Press the <ENTER>... -
Page 52: [Color Adjust] Menu
Chapter 4 Settings - [Color adjust] menu [Color adjust] menu On the menu screen, select [Color adjust] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fAfter selecting the item, press as to set. -
Page 53: [Color]
Chapter 4 Settings - [Color adjust] menu Operation Adjustment Adjustment range Press the a button. Increases the brightness of the dark (black) parts of the screen. 0 ~ +63 Press the s button. Reduces the brightness of the dark (black) parts of the screen. [Color] (Except for computer signal input) You can adjust the color saturation of the projected image. -
Page 54: [Sharpness]
Chapter 4 Settings - [Color adjust] menu Press the a button. Deepen green tone. [Green] 0 ~ +63 Press the s button. Lighten green tone. Press the a button. Deepen blue tone. [Blue] 0 ~ +63 Press the s button. Lighten blue tone. [Sharpness] You can adjust the sharpness of the projected image. -
Page 55: [Setting] Menu
Chapter 4 Settings - [Setting] menu [Setting] menu On the menu screen, select [Setting] from the main menu, and select an item from the sub-menu. COMPUTER 1 COMPUTER 2 Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fAfter selecting the item, press as to set. -
Page 56: [Lamp Control]
Chapter 4 Settings - [Setting] menu Note f It is set to [Off] when using the projector in the elevation of below 1 400 m (4 593’). It is set to [On] when using the projector in the elevation of above 1 400 m (4 593') and below 2 700 m (8 858'). Failure to do so may shorten the life of the internal parts and result in malfunctions. -
Page 57: [Key Lock]
Chapter 4 Settings - [Setting] menu f [Closed caption] can only be selected if an NTSC signal is input. f If [Closed caption] is set to the item except for [Off], the brightness of image may be changed according to the external devices or the used content of the closed caption corresponding connection. -
Page 58: [Hdmi Setup]
Chapter 4 Settings - [Setting] menu Operation Adjustment Range Press the a button. Turns up the volume. 0 ~ +25 Press the s button. Turns down the volume. Setting the mute Press as to select [Sound]. Press the <ENTER> button. f The [Sound] screen is displayed. -
Page 59: [Expand] Menu
Chapter 4 Settings - [Expand] menu [Expand] menu On the menu screen, select [Expand] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fAfter selecting the item, press asqw to set. -
Page 60: Input Search
Chapter 4 Settings - [Expand] menu [Input search] This function is used to detect the signals and project the automatic input signals automatically. This function is used to adjust [Fine sync], [H position], [V position] and [H.Size] automatically [Auto PC adj.] when input the analog computer signal. -
Page 61: [Keystone]
Chapter 4 Settings - [Expand] menu [Keystone] You can correct the trapezoidal distortion that occurs when the projector is installed tilted or when the screen is tilted. Press as to select [Keystone]. Press the <ENTER> button. f The [Keystone] screen is displayed. Press as to select one item. -
Page 62: Corner Correction
Chapter 4 Settings - [Expand] menu Press the <ENTER> button. f The [Keystone] screen is displayed. Press as to select [H/V Keystone]. Press the <ENTER> button. f The [H/V Keystone] individual adjustment screen is displayed. Press asqw to adjust the item. Items Operation Adjustment... - Page 63 Chapter 4 Settings - [Expand] menu Press the <ENTER> button. f The [Keystone] screen is displayed. Press as to select [Curved correction]. Press the <ENTER> button. f The [Curved correction] screen is displayed. Press asqw to adjust the item. Items Operation Adjustment Extend the vertical lines to left and...
-
Page 64: [Logo]
[Off] Displays nothing to project when the projector start-up. [Default] Displays the Panasonic logo when the projector start-up. [User] Displays the image registered by the user with the capture function. *1 [User] will be unavailable when the captured image is not registered. - Page 65 Chapter 4 Settings - [Expand] menu A confirmation screen is displayed, press as to select [Yes] and then press the <ENTER> button. f After capturing the image, the [Logo select] is set to [User]. The captured image will be displayed when the projector start-up next time.
-
Page 66: [Security]
Chapter 4 Settings - [Expand] menu f The [Logo PIN code] input screen is displayed. Press the <ENTER> button. Press as to enter the current Logo PIN code from 0 to 9 and press the <ENTER> button. Press the <ENTER> button. f The [New logo PIN code] input screen is displayed. -
Page 67: [Power Management]
Chapter 4 Settings - [Expand] menu The [PIN code] screen will be displayed when turn on the projector. The projector cannot be [On] operated without entering the PIN code. [Off] The projector can be operated without the PIN code. Note f If you want to correct the digit, press the <MENU>... -
Page 68: [Filter Counter]
Chapter 4 Settings - [Expand] menu Setting [Ready Countdown] in step 3) The time from the state which the management function is working to the standby mode can be set to 0 ~ 30 minutes when [Power management] is set to [Ready]. The increment is 1 minute. Press as to select [Ready Countdown]. -
Page 69: [Network]
Chapter 4 Settings - [Expand] menu [Off] Test pattern is not displayed. [Gray scale 1] [Gray scale 2] [Gray scale 3] [Gray scale 4] [Color bar] [Red] Select a test pattern so that it is easy to make various adjustments. [Green] [Blue] [Cross hatch]... -
Page 70: [Remote Control]
Chapter 4 Settings - [Expand] menu [Network information] Press as to select [Network]. Press the <ENTER> button. f The [Network] screen is displayed and then confirm the following items. [MAC address] Displays the MAC address of this projector. [IP address] Displays the current IP address of this projector. -
Page 71: [Memory Viewer] Menu
Chapter 4 Settings - [Memory Viewer] menu [Memory Viewer] menu On the menu screen, select [Memory Viewer] from the main menu, and select an item from the sub-menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. fAfter selecting the item, press as to set. -
Page 72: [Best Fit]
Chapter 4 Settings - [Memory Viewer] menu f The items will switch each time you press the button. [No rotate] Rotate is disabled. [270 Degrees] Rotates 270 degrees in anti-clockwise direction. [180 Degrees] Rotates 180 degrees. [90 Degrees] Rotates 90 degrees in anti-clockwise direction. [Best Fit] Set the image whether or not to fit with the projected screen. -
Page 73: [Info.] Menu
Chapter 4 Settings - [Info.] menu [Info.] menu On the menu screen, select [Info.] from the main menu. Refer to “Navigating through the menu” (x page 44) for the operation of the menu screen. [Info.] Display the status of the projector. Press as to select [Info.]. -
Page 74: Network Control
Chapter 4 Settings - Network control Network control Network connections The projector has a network function, and the following operations are available from the computer using the web browser control. f Setting and adjustment of the projector. f Display of the projector status. Note f A LAN cable is required to use the network function. -
Page 75: Computer Operation
Chapter 4 Settings - Network control Note f Please confirm with your network administrator before you connect to an existing network. f The following settings are set before the projector leaves the factory. [DHCP] [IP address] 192.168.1.100 [Subnet] 255.255.255.0 [Gateway] 192.168.1.1 [DNS] 192.168.1.1... - Page 76 Chapter 4 Settings - Network control Description of each item 1 [System Status] 4 [Image Setup] The [System Status] page is displayed by clicking this The [Image Setup] page is displayed by clicking this item. item. 2 [General Setup] 5 [Network Setup] The [General Setup] page is displayed by clicking this The [Network Setup] page is displayed by clicking item.
- Page 77 Chapter 4 Settings - Network control [Picture Setup] page 1 [Brightness] 4 [Color] Adjusts the brightness of the projected image. Adjusts the color saturation of the projected image. 2 [Contrast] 5 [Tint] Adjusts the contrast of the projected image. Adjusts the skin tone of the projected image. 3 [Sharpness] 6 [Color temperature] Adjusts the sharpness of the projected image.
- Page 78 Chapter 4 Settings - Network control 1 [Aspect] 7 [Auto PC adj.] Switches the aspect of the projected image. Executes the Auto PC adj. function. 2 [Fine sync] 8 [V Keystone] Adjusts the fine sync of the projected image. Corrects the keystone in vertical direction. 3 [H Position] 9 [H Keystone] Adjusts the horizontal position of the projected image.
-
Page 79: Using Useful Functions
Chapter 4 Settings - Using useful functions Using useful functions Memory Viewer function The Memory Viewer function makes it is possible to project the video and pictures which are stored in the USB memory when the USB memory is inserted into the projector. r What you can project with the Memory Viewer function Memory Viewer function supports the following image files. -
Page 80: Displaying The Pdf
Chapter 4 Settings - Using useful functions Executing the slide All pictures in the same folder will play automatically when [Sort Order] and [Slide Transition Effect] and so on of [Memory Viewer] menu are set to the special setting. Press asqw on the remote control to select a file. Press the <MENU>... -
Page 81: Termination Of The Memory Viewer
Chapter 4 Settings - Using useful functions Note f PDF display is switched at intervals. Please do not perform continuous operations during a short period of time. Termination of the Memory Viewer Press asqw to select the thumbnail which is displayed on the upper left corner. Press the <ENTER>... - Page 82 Chapter 4 Settings - Using useful functions [Active audio] / [Disable audio] Set whether to output the audio from the computer. [Play video] / [Pause video] Switch between play and pause the image. [Start] / [Stop] Set whether to display the image from the computer. [Exit] Displayed in gray and cannot be selected.
-
Page 83: Chapter 5 Maintenance
Maintenance Chapter 5 This chapter describes methods of inspection when there are problems, maintenance, and replacement of the units. ENGLISH - 83... -
Page 84: Power/Warning Indicators
Chapter 5 Maintenance - Power/Warning Indicators Power/Warning Indicators When an indicator lights up If a problem should occur inside the projector, the power indicator <ON(G)/STANDBY(R)> and the warning indicator <WARNING> will inform you by lighting or blinking. Check the status of the indicators and remedy the indicated problems as follows. - Page 85 Chapter 5 Maintenance - Power/Warning Indicators Power indica- Warning tor <ON(G)/ indicator Status Cause Solution STANDBY(R)> <WARNING> Lighting Projecting. f Is the lamp replacement warning icon displayed when turn on or turn off the projector? The replacement time of the f The indicator lights up Lighting Lighting in red...
-
Page 86: Maintenance/Replacement
Chapter 5 Maintenance - Maintenance/replacement Maintenance/replacement Before performing maintenance/replacement f When you perform maintenance or replacement of the parts, make sure to turn off the power and disconnect the power plug from the wall outlet. (x page 36) f Be sure to observe the procedure “Powering Off the Projector” (x page 36) when performing power supply operation. Maintenance Outer Case Wipe off dirt and dust using a soft dry cloth. -
Page 87: Cleaning/Attaching Air Filter Unit
Chapter 5 Maintenance - Maintenance/replacement Cleaning the air filter unit Remove the air filter unit beforehand according to the previously described procedure in “Removing the air filter unit”. Clean the air filter unit. f Vacuum dirt and dust from the air filter unit. f Do not wash the air filter unit. -
Page 88: Replacing The Unit
Attention f Panasonic takes no responsibility for any damage or malfunction of the product resulting from use of lamp units which are not manufactured by Panasonic. Use only specified lamp units. - Page 89 Chapter 5 Maintenance - Maintenance/replacement The displayed On-screen display time in [Lamp <WARNING> indicator counter] f The lamp replacement icon is displayed for 10 seconds. If you press any button within 10 seconds, the Over 5 700 hours icon disappears. less than 6 000 f The lamp replacement icon will display for 4 seconds...
- Page 90 Chapter 5 Maintenance - Maintenance/replacement f Perform step 2) in reverse direction to attach the lamp cover. Resetting the lamp counter Be sure to reset the lamp counter after replacing the lamp unit. Connect the power plug, press the power <v/b> button on the control panel or on the remote control. While pressing the a button on the control panel, press and hold the <INPUT/ENTER>...
-
Page 91: Troubleshooting
Chapter 5 Maintenance - Troubleshooting Troubleshooting Please check following points. For details, see the corresponding pages. Reference Problem Cause page f The power cord may not be connected. — f No electric supply is at the wall outlet. — f The circuit breakers have tripped. —... -
Page 92: Chapter 6 Appendix
Appendix Chapter 6 This chapter describes specifications and after-sales service for the projector. 92 - ENGLISH... -
Page 93: Technical Information
INST ? 11 12 21 22 23 31 41 51 query NAME ? Projector name query PROJECTOR Manufacturer name INF1 ? Panasonic Returns manufacturer name. query PT-LW330 / PT-LW280 / INF2 ? Model name query Returns model name. PT-LB360 / PT-LB330... -
Page 94: Pin Assignments And Signal Names
Chapter 6 Appendix - Technical Information <SERIAL IN> terminal The <SERIAL IN> terminal of the projector conforms with RS-232C so that the projector can be connected to and controlled from a computer. Connection Connecting terminals on projector Computer D-Sub 9p (female) D-Sub 9p (male) Communication cable (straight) Pin assignments and signal names... -
Page 95: Basic Format
Chapter 6 Appendix - Technical Information Basic format Transmission from the computer starts with STX, then the command, parameter, and ETX are sent in this order. Add parameters according to the details of control. Colon(1 byte) 3 command characters (3 bytes) Start (1 byte) Parameter (undefined length) End (1 byte) Basic format (with sub command) -
Page 96: Cable Specifications
Chapter 6 Appendix - Technical Information Cable specifications [When connected to a computer] Projector Computer (<SERIAL IN> terminal) (DTE specifications) Control commands When controlling the projector from a computer, the following commands are available. r Projector control command Command Control contents Parameter/return string Remark (parameter) Power on... -
Page 97: List Of Compatible Signals
Chapter 6 Appendix - Technical Information List of compatible signals The following table specifies the type of signals compatible with the projectors. f Symbols that indicate formats are as follows. V = VIDEO/S-VIDEO, R = RGB, Y = YC , H = HDMI Scanning frequency PnP * Dot clock... - Page 98 Chapter 6 Appendix - Technical Information Scanning frequency PnP * Dot clock Display resolution Mode frequency Format* Computer 1/ (dots) H (kHz) V (Hz) HDMI (MHz) Computer 2 MSXGA 1 280 x 960 60.0 60.0 108.0 1 280 x 1 024 64.0 60.0 108.0...
-
Page 99: Specifications
Chapter 6 Appendix - Specifications Specifications The specifications of the projector are as follows. Power supply AC 100 V - 240 V, 50 Hz/60 Hz 100 V - 240 V, ~ 3.5 A, 300 W Power consumption When [Standby mode] of [Setting] is set to [Eco]: 0.5 W When [Standby mode] of [Setting] is set to [Normal]: 6 W PT-LW330, PT-LW280 1.5 cm (0.59") (aspect ratio 16 : 10) - Page 100 Chapter 6 Appendix - Specifications Projection scheme [Front], [Rear], [Ceiling/Front], [Ceiling/Rear] (Menu setting system) PT-LW330, PT-LW280, PT-LB360, 10 W (monaural) x 1 PT-LB330 Built-in speaker PT-LB300, PT-LB280 2 W (monaural) x 1 1 (High-density D-sub 15 pin female) [RGB signal] 0.7 V [p-p] 75 Ω...
-
Page 101: Dimensions
Chapter 6 Appendix - Dimensions Dimensions <Unit : mm (inch)> 87 (3-7/16") 9 (11/32") 335 (13-3/16") 96 (3-25/32") 167.5 (6-19/32") 68.5 (2-11/16") Actual dimension may differ by product. ENGLISH - 101... -
Page 102: Ceiling Mount Bracket Safeguards
Ask a qualified technician to do the installation work such as mounting the projector on the ceiling. f Panasonic takes no responsibility for any damage to the projector resulting from use of a ceiling mount bracket not manufactured by Panasonic or the inappropriate choice of location for installation, even if the warranty period of the projector has not expired. -
Page 103: Index
Chapter 6 Appendix - Index Index Read this first!........2 [Red]/[Green]/[Blue] ......53 Accessing from the Web browser ..75 <IMAGE> button [Remote control] .........70 Accessories ........17 Remote control ......19, 41 Remote control ........19 Adjusting adjustable foot ....29 [Image mode]........52 [Repeat] ..........72 Air filter unit.........86 <INFO.>... - Page 104 Atıkların atılmasıyla ilgili yanlış uygulamalar yasayla belirlenmiş olan cezalara sebebiyet verebilir. Panasonic Corporation Web Site : http://panasonic.net/avc/projector/ © Panasonic Corporation 2014 Panasonic Systems Communications Company of North America 5th Floor, Two Riverfront Plaza, Newark, NJ 07102-5490 TEL: (877) 803 - 8492 Panasonic Canada Inc.