Casio 2369 User Manual

Module No. 2369
• If the digital display of your watch is continuously changing, see "To turn off
Auto Display" for information on how to stop it.
• Press C to change from mode to mode. After you perform an operation in any
mode, pressing C returns to the Timekeeping Mode.
Timekeeping Mode
Press C.
L A
B
P
C D
TIMEKEEPING MODE
In addition to time and date settings, the Timekeeping Mode also lets you adjust the
contrast of the digital display.
• The Timekeeping Mode is actually made up to four sub-modes. Press D to switch
between the sub-modes.
Time/Date
Month – Date
Day of week
L A
Press D.
B
P
C D
Seconds
PM indicator
Hour : Minutes
L
Date
• This watch displays text for the day of the week in any one of the five different
languages (English, German, French, Italian, and Spanish).
• See the "DAY OF THE WEEK LIST" at the back of this manual for information on
abbreviations used.
About Manual Time Setting and Time Calibration Signal Reception
The current time for this watch can be set by inputting the time and date you want
(manual setting) or by a time calibration signal. Note that the time calibration signal is
available only in certain areas in Europe. For details on time calibration reception and
the areas in which the time calibration signal is available, see the section of this
manual titled: "TIME CALIBRATION SIGNAL RECEPTION."
To set the current time manually
1. Press B while in the Timekeeping Mode. The current
L A
Auto Receive on/off setting flashes on the display
because it is selected .
B
• The receive indicator also flashes along with the
current on (
P
C D
2. Press C to change the selection in the following
sequence.
Receive indicator
Auto
DST
Receive
CNT
Date Month
• Auto Receive, DST, and GMT differential settings are used for time calibration
signal reception only. For details on these settings, see the section of this
manual titled: "TIME CALIBRATION SIGNAL RECEPTION."
• See the section of this manual titled "To adjust the display contrast" for details on
using the CNT (contrast) setting.
3. Press C until the language indicator is flashing on the
Language indicator
display.
• The language indicator shows the language currently
L A
set for the day of the week.
• The day of the week is set automatically in
B
accordance with the date.
4. Use A and D to change the language setting in the
P
C D
following sequence.
Hand Setting Mode
P
Analog
Seconds
ON ) /off ( OFF ) setting.
GMT
Language
differential
Year Minutes
GENERAL GUIDE
• Press L in any mode to illuminate the display for about two seconds.
Stopwatch Mode
Press D.
ENG
(English)
Press A.
5. Press C until the 12/24-hour indicator is flashing on the display.
•
12H indicates 12-hour format, while
6. Press D to toggle between the 12-hour (
• With the 12-hour format, the P (PM) indicator appears to the left of the digital
time for times in the range of noon to 11:59 pm. Times from midnight to 11:59 am
are shown without any indicator.
• With the 24-hour format, times are indicated in the range of 00:00 to 23:59, with
a 24 indicator to the left of the digital time.
7. Press C until the seconds digits are flashing on the display.
8. Press D to reset the seconds to
• If you press D while the seconds count is in the range of 30 to 59, the seconds
are reset to
the minutes count is unchanged.
9. Press C until the hour digits are flashing on the display.
10. Press D to increase the setting or A to decrease it. Holding down either button
changes the setting at high speed.
11. Repeat steps 9 and 10 to set the minutes, year, month, and date.
12. After you make the settings you want, press B to return to the Timekeeping
Mode.
• When you use the above procedure to set the digital display time, the hands of
the analog timepiece normally adjust according to your setting. If, for any reason,
the digital time does not match the analog time, use the procedure described
under "HAND SETTING MODE" to match the analog setting with the digital
display.
• The date can be set within the range of January 1, 1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is flashing,
the flashing stops and the watch goes back to the Timekeeping Mode
automatically.
To adjust the display contrast
CNT indicator
L
B
P
C
12/24-Hour
Format
About the backlight
In any mode, press L to illuminate the display for about two seconds.
Seconds
• The backlight of the watch employs an electro-luminescent (EL) panel, which loses
illuminating power after very long use.
• The illumination provided by the backlight may be hard to see when viewed under
Hour direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• The backlight remains lit for about two seconds from the point you press L, even if
it is already lit when you press L. If you keep L depressed for about 15 seconds,
the backlight will automatically turn off.
Telememo Mode
Alarm Mode
DEUT. FRA
(German) (French)
24H indicates 24-hour format.
12H ) and 24-hour (
00 .
and 1 is added to the minutes. If the seconds count is 00 to 29,
00
1. Press B while in the Timekeeping Mode. The current
Auto Receive on/off setting flashes on the display
because it is selected .
A
2. Press C 11 times until the
flashing on the display.
• The value to the right of the
current contrast setting. You can set the contrast to a
D
value from 1 (lightest) to 7 (darkest).
3. Use D to increase the contrast value and A to
decrease it.
4. After you make the setting you want, press B to return
to the Timekeeping Mode.
2369-1
World Time Mode
P
ITA ESP
(Italian) (Spanish)
24H ) formats.
(contrast) indicator is
CNT
CNT indicator shows the