Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
B/W CCD Camera
CCD-Schwarzweißkamera
Caméra CCD Noir et Blanc
CCD
About this manual
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d'installer et d'utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main
pour toute référence ultérieure.
VCB-3412P
VCB-3412PT
Advertisement
Table of Contents
Related Manuals for Sanyo VCB-3412P
Summary of Contents for Sanyo VCB-3412P
-
Page 1: Instruction Manual
INSTRUCTION MANUAL VCB-3412P BEDIENUNGSANLEITUNG VCB-3412PT MANUEL D’INSTRUCTIONS B/W CCD Camera CCD-Schwarzweißkamera Caméra CCD Noir et Blanc About this manual A propos de ce manuel Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce manual carefully. -
Page 2: Table Of Contents
SPECIFICATIONS.................. 12 • Externally adjustable flange back (mechanical focus) ACCESSORIES ..................14 • Low power consumption and quick start • 12 V DC operation – VCB-3412P (with AC adaptor) – VCB-3412PT (without AC adaptor) • Built-in Mirror image effect function. English... -
Page 3: Precautions
Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust. -
Page 4: Parts Names
PARTS NAMES Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. External sync composite video signal input connector (VS IN: BNC type) Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor. - Page 5 PARTS NAMES Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Flange-back adjustment screw (FLANGE BACK ADJ.) Flange-back lock screw (FLANGE BACK LOCK) Camera installation bracket The bracket can be fixed at the top or bottom of the camera.
- Page 6 ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the A.I. LENS switch to the VIDEO position.) Compatible auto-iris lenses 1/3 inch Sanyo DC type lens VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm...
-
Page 7: Mounting The Lens
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “L” is more than 7 mm. If not, that may damage the camera and prevent proper installation. Remove the lens mount cap from the camera. - Page 8 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.
-
Page 9: Connections
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. Connect DC connecting cord from the AC adaptor to the 12 V DC IN terminal on the camera. •... -
Page 10: Settings
SETTINGS Camera setup section Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI VR401 switch to ON position. Note: VIDEO Please refer to the specifications for dynamic A. -
Page 11: Backlight Compensation Setting
SETTINGS Lens iris adjustment Backlight compensation setting If using a DC type auto-iris lens, you will need to set the LEVEL Use an auto-iris lens and set the BLC switch to the ON position, to (VR401) volume when shooting in the conditions described below. engage the backlight compensation function. -
Page 12: Troubleshooting
Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen •... -
Page 13: Specifications
Servicing should always be referred to your dealer or Electronic iris range : 0.07 lux to 42,000 (F 1.2, lens) 0.1 lux to 57,000 (F 1.4, lens) Sanyo Authorized Service Centre. : 12.5 mm ± 0.8 mm Flange-back : γ = 0.45... - Page 14 SPECIFICATIONS Dimensions 108.5 99.5 VIDEO OUT VS IN POWER Approx. 1.8 m Approx. 1.8 m 1/4”–20 UNC Features and specifications are subject to change without prior notice or obligations. English...
-
Page 15: Accessories
ACCESSORIES C mount adaptor (5 mm)............1 pc. The C mount adaptor must be used to be able to install a C mount lens on the camera. Lens iris plug (4-pin)..............1 pc. AC adaptor ................1 pc. AC adaptor mounting plate ............1 pc. : With 3 fixing screws Clamping core A ...............