Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for g-lites 250S
Summary of Contents for g-lites 250S
-
Page 1: User Manual
User Manual MOVING HEAD MODEL: 250S www.g-lites.com... -
Page 2: Table Of Contents
5.2. - LAMP ADJUSTMENT 5.3. – RIGGING 5.4. - DMX-512CONNECTION/CONNECTIONBETWEENFIXTURES 5.5. - CONNECTIONWITH THE MAINS 6. – OPERATION 6.1. – ADDRESSING 6.2. - DMX-PROTOCOL 6.3. - SPECIAL SETTINGS 7. - CLEANING AND MAINTENANCE 7.1. -REPLACING THE FUSE TECHNICAL SPECIFICATION GENERAL TROUBLESHOOTING www.g-lites.com... - Page 3 C. Warranty is void if the product is misused, damaged or modified in any way, or for unauthorized repairs or parts D. For maintenance or lamp replacement, disconnect the fixture from main power before opening the moving head. www.g-lites.com...
-
Page 4: Introduction
250S 1．INTRODUCTION Thank you for having chosen this MOVING HEAD LIGHT .You will see you have acquired a powerful and versatile device. Unpack your moving-head light. Before you initial start-up, please make sure that there is no damage caused by transportation. - Page 5 Caution: During the operation, the housing becomes very hot. Danger of fire! Never install the device on highly flammable surfaces (e.g. fair carpet)! HEALTH HAZARD! Never look directly into the light source. As sensitive persons may suffer an epileptic shock (especially meant for epileptics)! www.g-lites.com...
-
Page 6: Operating Determination
If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, lamp explosion, crash www.g-lites.com... -
Page 7: Description Of The Device
3-digit LED display for starting address. For bright 250W discharge lamp. Suitable controllers: DMX Operator. 4．2 Overview (1) Projector head (2) Objective lens (3) Yoke (4) Power switch (5) DMX-IN socket (6) Carrying handle (7) Power supply (8) DMX-OUT socket (9) Fuse (10) Display (11) DIP-switches (12) Function-DIP-switches www.g-lites.com... -
Page 8: Installation
Step 4: Insert the lamp into the lamp holder. Step 5: Replace the lamp holder and tighten the knurled-head screws. Step 6: Adjust the lamp as described under lamp adjustment. Step 7: Replace the lamp cover and tighten the fixation screws. www.g-lites.com... -
Page 9: Lamp Adjustment
1 hour without any harming deformation. The installation must always be secured with a secondary safety attachment. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if www.g-lites.com... - Page 10 When installing the device, make sure there is no highly-inflammable material (decoration articles, etc.) within a distance of min.0.5m. CAUTION! Use 2 appropriate clamps to rig the fixture on the truss. Follow the instructions mentioned at the bottom of the base. www.g-lites.com...
- Page 11 Insert the quick-lock fasteners of the first Omega-holder into the respective holes on the bottom of the device. Tighten the quick-lock fasteners fully clockwise. Install the second Omega-holder. DANGER Before taking into operation for the first time, the installation has to be approved by an expert! www.g-lites.com...
- Page 12 DMX-controllers with other XLR-outputs, you need to use adapter-cables. Building a serial DMX-chain: Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected. www.g-lites.com...
-
Page 13: Connectionwith The Mains
Please make sure that you don’t have any overlapping channels in order to control each moving-head light correctly and independently from and other fixture on the DMX data link. If two, three or more moving-head light is addressed similarly, they will work similarly. www.g-lites.com... - Page 14 -The 3 PIN XLR plug (cable with DMX signal from controller) is not connected with the input of the moving-head light. -The controller is switched off or defective, if the cable or connector is defective or the signal wires are swap in the input connector. www.g-lites.com...
-
Page 15: Special Settings
Channel 8: Auto focus control 6．3 Special settings Mode/ Function DIP-switch no. Not occupied Call up color separately Set color to every position Set 16-bit-mode Invert PAN-movement Invert TILT-movement Via the Function-DIP-switches, you can adjust different modes and settings: www.g-lites.com... -
Page 16: Cleaning And Maintenance
The dichroic color-filters, the gobo-wheel and the internal lenses should be cleaned monthly. There are no serviceable parts inside the device except for the lamp and the fuse. Maintenance and service operations are only to be carried out by authorized dealers. Please refer to the instructions under “Installing/ replacing the lamp”. www.g-lites.com... -
Page 17: Replacing The Fuse
Should you need any spare parts, please use genuine parts. If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply cable available at your dealer. Should you have further questions, please contact your dealer. www.g-lites.com... -
Page 18: Technical Data
Precise adjustment on horizontal and vertical position Precise speed adjustment on horizontal and vertical position INPUT DMX 512 signal 10 CH (16 Bit) or 8 CH (8 Bit) SET UP Auto test all functions Display the value of each DMX channel www.g-lites.com... - Page 19 200-220 V – 60 Hz 100-120 V – 60 Hz (optional) 220-240 V – 50 Hz (optional) POWER Power Consumption: 400 W DIMENSION L 420 W 390 H 560 mm L 16.53 W 15.35 H 22.05 inches WEIGHT 23 Kg www.g-lites.com...
-
Page 20: General Troubleshooting
Please check the electric part (such as the switch, transformer, ballast, electric capacity, piezo resistor, filter, PCB board, controller to motor). Pan or Tilt position is off: o Verify that all belts are tight. o Home the fixture. www.g-lites.com...