NETGEAR TA612V Installation Manual page 2

• Don't forget to visit our customer account web portal online. You can:
- Check your balance
- Access your call records
- Recharge from the convenience of a webpage,
visit: http://www.mynetfone.com.au/ and follow the
My Account link.
INSTALLATION WITH A ROUTER
This guide shows you how to set up your Broadband Voice Adapter with a Router
or Switch instead of just a single PC. This way you can share your internet connect-
ion with multiple computers (i.e. via Wireless Lan).
1. SET UP THE NETWORK CONNECTIONS
a. Unplug the power cable for your modem.
b. Unplug the power cable for your router.
c. Disconnect the Ethernet cable connecting your modem to your
router from the WAN/Internet port on your router, and connect that
end of the Ethernet cable to the Internet port on the TA612V Voice
Adapter.
d. Connect one end of the Ethernet cable we provide into the PC port
on the TA612V. Connect the other end of this Ethernet cable into the
WAN/Internet port on your router.
e. Plug the power cable back into your modem. Wait about two minutes
for it to start up.
2. THEN, INSTALL THE TA612V VOICE ADAPTER
a. Plug the power cable into the Power port on the TA612V Voice Adapter
and into an electrical outlet. This turns on your Voice Adapter. You do
not need to unplug it when not in use.
Restore PC
12VDC, 1.2A
Factory
Phone 2 Phone 1
Power
Settings
b. Check that the Power light
Wait at least five minutes for the phone adapter to start up.
There may be updates that need to be downloaded such as new
firmware or changes to your features. Do not interrupt the
registration process by unplugging the power or lifting the receiver
on your phone during the start-up process. Interruption of the
startup may result in interruption of service.
c. The status light on the front of the TA612V will flash. Wait two
minutes before continuing.
d. Plug the power cable back into your router and wait about two
minutes for it to start up before continuing.
e. Connect a telephone to the TA612V Phone 1 port using the adapter
provided.
f. If you have a DSL modem that requires PPPoE you need to set up
your PPPoE username and password in the TA612V.
Point your browser to:
http://192.168.61.1/
Log in using the username and password printed on the back of the
TA612V. After setup reboot your TA612V.
3. SET UP AN ACCOUNT AT MYNETFONE
a. Power up the computer.
b. Use a Web browser to go to the MyNetFone web site,
http://www.mynetfone.com.au/register/
Follow the instructions to set up your account. During this process,
MyNetFone will verify your system configuration and phone set up.
You will be asked to provide the following information:
- Enter the serial number and MAC address of your TA612V,
located on the base of the unit.
- Enter your name and contact information.
- Select your MyNetFone plan.
visit: http://www.mynetfone.com.au/plans/ for more
information.
c. After registration, you will be required to reboot your TA612V.
d. Pick up your telephone handset and listen for a dial tone. If you hear a
Internet
dial tone then you have finished installation and may begin making
calls. For dialing instructions, see the Helpfule Hints on this card. If you do
not hear a dial tone, see Troubleshooting.
on the Voice Adapter is illuminated.
TROUBLESHOOTING
If you have no dial tone, check the following:
•
•
•
e. To check your MyNetFone number dial 151 and select option 2.
Blink=Activity Ethernet: Green=100Mbps/Amber=10Mbps
Phone 1
Internet
Power
PC
Status
Make sure the phone is plugged into the proper port on the Voice
Adapter (phone port #1)
Make sure the Internet light on the Voice Adapter is active. If not,
check your connection to the Internet. Try rebooting your modem. If
that does not work, contact MyNetFone Customer Care.
This Voice Adapter is not supposed to be used behind a Router. Please
connect it directly to the modem.
Your Broadband VoIP Phone Service
www.mynetfone.com.au 1300 731 048
or call us on
www.mynetfone.co.nz 0800 686 383
or call us on
Phone 2