-20 °C to + 60 °C (-4 °F to + 140 °F) Tape speed (kilohms) SP: Approx. 18.81 mm/s DV input/output (DCR-HC28E) Dimensions (approx.) 56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in.) LP: Approx. 12.56 mm/s i.LINK Interface (IEEE1394, 4-pin...
Page 3
Model information table Model DCR-HC28E Destination Color system DV Interface IN/OUT • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model : East European model HK : Hong Kong model...
Page 4
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
TABLE OF CONTENTS Section Title Page SERVICE NOTE 1-1. Power Supply During Repairs ········································· 1-1 1-2. To Take Out a Cassette when not Eject (Force Eject) ····· 1-1 1-3. Setting the “Forced Power On” Mode ····························· 1-1 1-4. Using Service Jig ····························································· 1-2 1-5.
1. SERVICE NOTE 1-1. POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following method is available to prevent this. Method: Use the AC power adaptor (AC-L25A/L25B).
1-4. USING SERVICE JIG Connect the CPC-15 jig connector (J-6082-564-A) and I/F unit for LANC conrol (J-6082-521-A) to the CN1014 of VC-416 board. I/F unit for LANC control (J-6082-521-A) VC-416 BOARD (SIDE A) CPC-15 (J-6082-564-A) 1-5. SELF-DIAGNOSIS FUNCTION 1-5-1. Self-diagnosis Function 1-5-2.
Page 8
1-5-3. Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Non-standard battery is used. Use the InfoLITHIUM battery. Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. LOAD direction.
Exif Model Data Data Page Address DCR-HC28E Writing Method: 1) Select page: 0, address: 01 and set data: 01. 2) Select page: C, address: D2 to D4, and set the Exif Model Data. Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
2. DISASSEMBLY NOTE FOR REPAIR • Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some •...
Page 11
HELP HELP 2-1. DISASSEMBLY EXPLODED VIEW HARDWARE LIST 2-1-1. OVERALL ASSEMBLY 2 NS Cabinet Assy 2-3 (#2) 2-2 (#2) 1-2 (#14) 1-3 (Direction of the arrowA) (Claw) 1-1 (Slide the EVF) 2-1 (Open the Cassette Lid) (Shaft) 3-4 (Boss) 1-12 (Boss) 1-4 (#14) 1-5 (#14) 3-1 (Open the Jack Lid)
Page 15
HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. THE METHOD OF ATTACHMENT OF FP-380 FLEXIBLE BOARD 1 Fold dotted line parts of the FP-380 flexible board 3 Roll the the FP-380 flexible board 90 degrees. as shown in figure.
3-2. OVERALL BLOCK DIAGRAM (2/5) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. N MECHA DECK (MDX-N110) VC-416 BOARD (2/5) VIDEO HEAD CN1014 RECDT RF_MON CN1008 RECA1, RECA2 XODD, YODD OVERALL (1/5) XCS_EEP...
3-6. POWER BLOCK DIAGRAM (1/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. FP-381 VC-416 BOARD (1/3) Q2207, Q2208 FLEXIBLE F002 CAPSTAN/ C/D_UNREG BOARD DRUM CN2001 SWITCHING F003 ACV_UNREG J001 VTR_UNREG...
3-7. POWER BLOCK DIAGRAM (2/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. VC-416 BOARD (2/3) CD-631 BOARD CN3001 CN101 L101 CAM_15V CAM_15V IC101 CAM_-7.5V CAM_-7.5V IMAGER A_2.8V FB6001 USB_3.1V L3001...
3-8. POWER BLOCK DIAGRAM (3/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. VC-416 BOARD (3/3) CONTROL KEY BLOCK (SS17000) (2/2) CN1012 RV001 (2/2) D_2.8V (ZOOM) D003 CAMERA D002 D_2.8V MODE_LED_VDD...
4-2. SCHEMATIC DIAGRAMS Link Link CD-631 BOARD (CCD IMAGER) LB-121 BOARD (EVF, EVF BACKLIGHT) PD-281 BOARD (LCD, LCD BACKLIGHT) FP-381 FLEXIBLE BOARD (DC IN) FP-380 FLEXIBLE BOARD FP-031, FP-032, FP-228 FLEXIBLE BOARD FP-386 FLEXIBLE BOARD CONTROL KEY BLOCK (CF17000) (PANEL REVERSE DETECT) SI-051 BOARD (AV/DV/USB CONNECTOR) CONTROL KEY BLOCK (SS17000) COMMON NOTE FOR SCHEMATIC DIAGRAMS...
Page 27
4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection •...
Page 28
Note:IC101 is not included in CD-631 complete board. CD-631 BOARD Note:Voltages and wavefroms of IC101 can not be measured,because this is mounted by side of the lens. CCD IMAGER XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE P:PB MODE CN101 CCD_OUT V_DRAIN CL102...
Page 29
Schematic diagrams of the VC-416 board are not shown. Pages from 4-6 to 4-17 are not shown. DCR-HC28E_L2...
Page 31
• Refer to page 4-3 for mark 0. SI-051 BOARD AV/DV/USB CONNCTOR XX MARK:NO MOUNT CN601 10P NO MARK:REC/PB MODE AUDIO L LANC_SIG LANC_SIG S GND LANC_DC Vref C604 R618 R619 LANC_DC R608 S_C_I/O R611 AUDIO_R_I/O C610 A/V OUT AUDIO R R609 MULTI_JACK_IN FB602...
Page 32
FP-381 FLEXIBLE BOARD LB-121 BOARD DC IN Note: BH001 and J001 are not included EVF,EVF BACKLIGHT in FP-381 flexible board. XX MARK:NO MOUNT LND001 BATT_UNREG LND002 BATT_UNREG BH001 LND003 BATT_UNREG (BATTERY TERMINAL) LND004 BATT_UNREG LND005 CN301 BATT_UNREG D302 R303 NESW007T-T017 LND006 LED_K N.C.
Page 34
CONTROL KEY BLOCK (SS17000) CONTROL KEY BLOCK (CF17000) CONTROL KEY BLOCK (SS17000) is replaced as block, CONTROL KEY BLOCK (CF17000) is replaced as block, so that PRINTED WIRING BOARD is omitted. so that PRINTED WIRING BOARD is omitted. LND009 REG_GND LND001 CHASSIS_GND ZOOM_VR...
4-3. PRINTED WIRING BOARDS Link Link CD-631 BOARD SI-051 BOARD PD-281 BOARD (SIDE A) LB-121 BOARD PD-281 BOARD (SIDE B) FP-381 FLEXIBLE BOARD FP-386 FLEXIBLE BOARD FP-031, FP-032, FP-228 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION DCR-HC28E_L2...
Page 36
4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. Transistor Diode • : Circuit board : Flexible board Pattern from the side which enables seeing. : pattern of the rear side (The other layers’...
Page 37
CD-631 (2 layers) : Uses unleaded solder. CD-631 BOARD (SIDE A) CD-631 BOARD (SIDE B) IC101 Note: IC101 is not included in CD-631 complete board. 1-868-293- 1-868-293- 21 DCR-HC28E_L2 CD-631 4-26...
Page 38
Printed wiring boards of the VC-416 board are not shown. Pages from 4-27 to 4-28 are not shown. DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2...
NOTE NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. EXPLODED VIEWS EXPLODED VIEWS Link Link OVERALL ASSEMBLY FRONT PANEL BLOCK CABINET (R) BLOCK MAIN BLOCK-1 MECHANISM DECK EVF BLOCK...
Page 47
5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service.
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1. EXPLODED VIEWS 5-1-1. OVERALL ASSEMBLY Main Block-1 (See page 5-5.) Front Panel Block Cabinet (R) Block (See page 5-3.) (See page 5-4.) Ref. No. Part No. Description Ref. No. Part No. Description X-2108-030-1 CABINET (172) ASSY, NS 2-635-562-31 SCREW (M1.7) (Black) 2-664-983-31 CABINET (UPPER (172))
Page 49
5. REPAIR PARTS LIST HARDWARE LIST 5-1-2. FRONT PANEL BLOCK ns: not supplied BT601 S I - MIC901 : BT601 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-31.) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Page 50
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-3. CABINET (R) BLOCK ns: not supplied SP901 (Note) LCD901 - 2 8 Note: Be sure read “HELP” when you install the FP- 380 flexible board. Ref. No. Part No. Description Ref. No. Part No.
Page 51
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-4. MAIN BLOCK-1 ns: not supplied EVF Block (See page 5-7.) Main Block-2 (See page 5-8.) J001 (Note) BH001 (Note) Lens Block (See page 5-6.) Note: BH001 and J001 are not included in FP-381 flexible board.
Page 52
5. REPAIR PARTS LIST HARDWARE LIST 5-1-5. LENS BLOCK - 6 3 IC101 (Note1, 2) Note 1: IC101 is not included in CD-631 complete board. Note 2: Be sure to read “Precuations for Replacement of Imager” on page 4-3 when changing the imager. Ref.
Page 54
5. REPAIR PARTS LIST DISASSEMBLY HARDWARE LIST 5-1-7. MAIN BLOCK-2 ns: not supplied Mechanism Deck Section (See page 5-9.) - 4 1 Ref. No. Part No. Description Ref. No. Part No. Description 2-664-982-01 SCREW, TRIPOD 2-635-562-31 SCREW (M1.7) (Black) * 302 2-664-976-01 FRAME (171), BOTTOM 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) 1-479-507-41 KEY BLOCK, CONTROL (SS17000)
Page 55
5. REPAIR PARTS LIST 5-1-8. MECHANISM DECK SECTION ns : not supplied M901 LS chassis block assembly (See page 5-10) Ref. No. Part No. Description Ref. No. Part No. Description X-2024-478-1 PENDULUM ASSY 2-342-933-02 PLATE, TOP 2-342-917-02 LED BASE 2-342-927-01 SPRING (ARM T), TENSION COIL 7-627-850-77 SCREW, PRECISION +P 1.4X1.8 2-541-585-01 SHEET, FLEXIBLE ADHESIVE 3-079-366-11 RELEASE, REEL LOCK...
Page 56
5. REPAIR PARTS LIST 5-1-9. LS/MECHANICAL CHASSIS BLOCK ASSEMBLY-1 ns : not supplied (Note) (Note) LS / Mechanical chassis block assembly-2 (See page 5-11) Note: These two screws are the fixing screws of the LS cam plate. These two fixing screws are used for adjsting the LS cam plate position. (refar to 4-2.
Page 57
5. REPAIR PARTS LIST 5-1-10. LS/MECHANICAL CHASSIS BLOCK ASSEMBLY-2 ns : not supplied D901 Q901 S901 M902 Q902 804 810 FP-031 FP-032 (Note 1) H902 (Note 1, 2) (Note2) MIC902 H901 FP-031 (Note 1) Note1: The FP-031 and FP-032 are supplied as the assembled part of the MD (N100) sub ass'y A by attaching them with the adhesive agent.
Page 61
HARDWARE LIST #1: M1.7 X 2.5 (Black) #2: M1.7 X 4.0 (Black) #3: M1.7 X 2.5 (Red) #4: M1.4 X 2.5 (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 #5: M1.7 X 3.5 (Black) #6: M1.4 X 1.7 (Silver) #7: M1.7 X 1.6 (Black) #8: M1.7 X 3.5 (Silver) 3-080-204-01 2-598-474-01...
Page 62
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once • To reverse the previous screens (operation) one by one, click 1. Click the Print button 2.