CUSTOMIZING YOUR KEYSET
AME PASSWORD
This feature allows people using the AME feature to enable password protection.
This will prevent unauthorized people from listening to your messages being left.
The passcode is the same as your station passcode. This feature only applies if
there is an SVM card installed in the system and your keyset has a programmed
AME key.
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 101 to turn on AME PASSWORD or 100 to turn it off.
•
Press TRSF to store your selection.
AUTO CAMP-ON
This option allows intercom calls to be automatically camped on, if possible, when
a busy station is called.
•
With the handset on-hook, press TRSF and then dial 110.
•
Press 081 to turn CAMP-ON on or 080 to turn it off.
•
Press TRSF to store your selection.
SELECT RING TONE
Each keyset user can select any one of eight ring frequencies:
•
While on-hook, press TRSF and then dial 111.
•
Dial 1–8 or press the UP and DOWN keys to hear each tone.
•
When you hear the tone that you prefer, press TRSF to save it.
NOTE: Specific lines or stations may be programmed to ring with a different tone
than what you have selected for you keyset.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234.You can change your station pass-
code whenever you desire.
•
While on-hook, press TRSF and then dial 101.
•
Dial your old passcode.
•
Dial a new passcode (must be four characters). You can use 0–9.
•
Redial the new passcode to verify. If successful, you will hear two beeps. Four
beeps indicate an incorrect code. Reenter the code again.
•
Press TRSF to store the new passcode.
40
Home Page
SET ANSWER MODE (INTERCOM)
You can receive internal calls in one of three modes
under Intercom Calls for
descriptions):
•
While on-hook, press TRSF and then dial 103.
•
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
•
Press TRSF to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have Forward
No Answer (FNA) turned on, you must answer screened transfers by pressing
ANS/RLS or the MONITOR key if you are using a 7B phone before your FNA timer
expires or the call will forward.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
•
While on-hook, press TRSF and then dial 110.
•
Dial 15 to access AUTO ANS CO.
•
Press the VOLUME UP or DOWN key to change the status.
•
Press TRSF to store your selection.
AUTOMATIC HOLD
While on an outside call, pressing a line key, route key or a flashing CALL button
will automatically put your call on hold and connect you to the next call. This fea-
ture can be turned on or off at your keyset.
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 001 to turn Automatic Hold on or 000 to turn it off.
•
Press TRSF to store your selection.
NOTE: Intercom calls can only be automatically put on hold by pressing TRSF.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When using
headset mode, press the ANS/RLS or the MONITOR key if you are using a 7B
phone to answer and release calls.
•
With the handset on-hook, press TRSF and then dial 110.
•
Dial 021 to use the headset or 020 to use the handset.
•
Press TRSF to store your selection.
DCS Keyset
Table of Contents
(see Answering Intercom Calls
41