Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Pioneer Brite Striper 2000
- Page 1 BRITE STRIPER ® 2000 INSTRUCTION MANUAL & PARTS LISTING...
- Page 2 Replacement parts for all of Pioneer’s machines are fully stocked and available for immediate de- livery. We also carry replacement parts for many other airless line stripers. Call your local representative or Pioneer for more information.
-
Page 3: Table Of Contents
TABLE OF CONTENTS ® THE BRITE STRIPER 2000 ASSEMBLY INSTRUCTIONS Tools Necessary for Assembly ......1 Removing from Shipping Carton . -
Page 4: Assembly Instructions
® FOR BRITE STRIPER MODEL #2000 After Removing Box from Shipping Carton: STEP 1. Remove Brite Striper 2000 – two people necessary to lift STEP 2. Remove handle bar. Remove box conaining: 12 Ft. Hand Hose Assembly Hand Hose Wand... -
Page 5: Speed Control Cable
STEP 4. SPEED CONTROL CABLE PARTS REQUIRED: Throttle Control Cable is already attached and pre-set at Speed Control Lever. 2 - 3/4" x 1/4" - 7/16" Hex Head Bolts 2 - 7/16" Hex Head Self Locking Nuts TOOLS REQUIRED: 7/16" Socket 7/16"... -
Page 6: Adjustable Spray Box
STEP 5. Adjustable Spray Box Parts required: a. Snap ring b. Adjustable spray box Step 1: Slide adjustable spray box bar on the front axle Step 2: Attach carriage bolt, washer, lock washer and wingnut Step 3: Attach snap ring on end of axle to prevent spray box bar from sliding off Step 4: Attach free end of paint line hose to shut-off valve and Tighten with 5/8”... -
Page 7: Before Starting
BEFORE STARTING The 2000 STRIPER is shipped with engine oil. Be sure to check the en- closed Operating and Maintenance instructions for proper oil. Follow fill- ing directions. 1.Carefully read and follow instructions for starting and maintaining the engine (in a separate booklet furnished with your machine). 2.Check all hose connections and fittings making sure they are tight. -
Page 8: Care And Operation Of Paint Tank Unit
CARE AND OPERATION OF PAINT TANK UNIT DIRECTIONS FOR OPERATING: 1. Remove pump assembly by raising locking lever to vertical position, and turning counter- clockwise until ends of locking lever reach slots in locking ring; lift out. 2. Mix paint (in pail - not in tank) and strain through cloth or fine sieve. Paint Strainer Fil- ters packaged 25 per case are available. -
Page 9: Operation Of Machine
OPERATION OF MACHINE 1. Check to make certain that brass bleed-off valve (located on cross fitting) is in closed position so air will not escape. 2. Make certain that your V-belt is tight. WARNING: NEVER OPERATE UNIT WITHOUT BELT GUARD IN PLACE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY OR DAMAGE. -
Page 10: Parts List & Parts Explosion Drawings
PARTS LIST ® BRITE STRIPER MODEL 2000 KEY# PART # DESCRIPTION KEY# PART # DESCRIPTION 1503 Hand Grip 1102 Pump Assy. 1505 Paint Control Lever 0076 Rubber End Pump Assy. 0119 * Tank Gasket 1636 Paint Control Cable 2065 Speed Control Cable 2071 17”... - Page 11 PARTS LIST ® BRITE STRIPER MODEL 2000 Obscured by Rear Wheel MODEL 2000...
-
Page 12: Striping Tips
STRIPING TIPS When striping always have the machine in motion before opening the spray valve, thus eliminating a heavy “blob” of paint at the beginning. If striping on an asphalt or concrete surface you may have a build-up of paint on the edges of your line. This can be corrected by adjusting the tip so the fan spray is angled at 45 degrees to each side plate. -
Page 13: Clean-Up Of The Paint Tank Unit
MAY RESULT IN PERSONAL INJURY OR DAMAGE. 4. Remove Pump Assembly. Hose the inside of the tank to remove any excess paint. Fill tank 3/4 full with water and Pioneer P.H.D. Solution. Scrub inside of paint tank with soft nylon bristle brush, available through Pioneer, Item # TBrush. -
Page 14: Clean-Up Tips
All parts of your PIONEER Brite Striper 2000 should be cleaned immediately after each use. We recommend Pioneer P.H.D. Cleaner. A clean, lint-free rag should be used to wipe dry the inside of the tank. A final step should then be to remove the nozzle caps and clean the nozzle tips and screens. -
Page 15: Trouble Shooting The #2000
TROUBLE SHOOTING ® Brite Striper Model #2000 STRIPER DOES NOT STRIPE FULL LINE 1. Was paint strained? 2. Check paint level. 3. Check nozzle screen for clogs. Clean as needed. 4. Check nozzle tip for proper alignment — horizontal. 5. Check operating pressure — is air releasing through safety release valve on compressor? 6. - Page 16 AIR LEAKS PUMP ASSEMBLY LEAKS AIR 1. Shut off machine. 2. Bleed pressure from paint tank. 3. Remove pump assembly and check tank gasket for damage – replace if needed. Re-seat in pump assembly. Do not overtighten. 4. Check that brass tube is threaded tightly against top of pump assembly.
-
Page 17: Customer Service
FOR ANY REPAIRS INCLUDING WARRANTY REPAIRS: Call 1-800-877-1500 for repair cost estimates, and full service information, INCLUDING RETURN AUTHORIZATION CODE NUMBER, BEFORE SENDING YOUR UNIT. SEND YOUR UNIT, FREIGHT PREPAID TO: PIONEER MANUFACTURING COMPANY 4529 Industrial Parkway Cleveland, Ohio 44135 MODEL 2000... -
Page 18: Limited Warranty
PIONEER MANUFACTURING COMPANY INC.’S RESPONSIBILITY IS LIMITED TO THE COST OF THE PRODUCT ITSELF. No representative employee, agent of Pioneer, or any other person has any au- thority to assume for Pioneer any additional or other liability or responsibility, other than as described above, in connection with the BRITE STRIPER. - Page 19 P.H.D. • Exclusive formula provides the Specially Design Cleaning Concentrate brightest, whitest lines in the industry • Specially designed to clean Pioneer • Premium field marking paint for Athletic Field Marking Machines. special events, playoffs and high pro- • Biodegradable file teams •...
- Page 20 Available in a • Any grass or paved areas Variety of Colors Packaging •Pioneer offers 16 standard colors and an unlimited variety of custom colors. Five gallon pails; One gallon • Customize your fields with your school containers, 4 per case.