Page 1: Table Of Contents
1-11 1. 7 Component Location ................1-13 1. Outer view ..................1-13 2. Inner view ..................1-14 3. Fan/Motor Location (FP-D250/D350/D350H) ........1-16 4. Fan/Motor Location (FP-D450/D600) ..........1-17 5. Sensor Location ................1-18 6. Solenoid/Clutch/Discharge lamp Location ........1-19 7.
Page 2 System Control PCB (FP-D250/D350 Series) ........4-53 4. 4 Control Panel PCB (FP-D250/D350 Series) ........4-71 1. Control Panel CPU PCB (FP-D250/D350 Series) ......4-71 2. Control Panel PCB A (FP-D250/D350 Series) ......... 4-77 3. Control Panel PCB B (FP-D250/D350 Series) .........
Page 3 4. 8 LSU Image Data Control PCB (FP-D250/D350 Series) ....... 4-100 4. 9 Automatic Duplex Unit (ADU) Driver PCB (Option) (FP-D250/D350 Series) ... 4-104 4. 10 Low Voltage Power Supply PCB (FP-D250/D350 Series) ....4-109 4. 11 High Voltage Power supply PCB (FP-D250/D350 Series) ....
Page 4 6. 10 Hard Disk Driver for back up (FA-HD02) ..........6-35 6. 11 Hard Disk Driver for Image memory (FA-HD03/HD04) ......6-37 VIl. Glossary of Terms Network, Printing, Copying and imaging Terms ........TORANO-MAKI (FP-D250/D350 Series) TORANO-MAKI (FP-D450/D600 Series) Electrical schematic diaglam...
Page 5 This manual was developed and is supplied to authorized servicing dealers by Panasonic Co. for the sole purpose of providing information necessary for the equipment’s proper support. It is intended that this information be confidential and may not be reproduced without prior written consent from Panasonic Co.
Page 6 For U.S.A For your safety Caution This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Invisible laser radiation when open. Peligro-Cuando la cubierta esté abierta se DANGER PRECAUTION Avoid direct exposure to beam.
Page 7 For your safety Caution This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Invisible laser radiation when open. Peligro-Cuando la cubierta esté abierta se DANGER PRECAUTION Avoid direct exposure to beam.
Page 8 Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. For Sweden, and Denmark SPECIALSÄKRING: ENDAST AV APPARATFABRINKANTEN LEVERERAD SÄKRING FåR ANVÄNDAS. VARNING! Explosionsfara vid felaktigt batteribyte.
Page 9 If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR OFFICE THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
Page 10: Introduction
Ledger (11" × 17") / A3 (297 × 420mm) Maximum original size Paper feed Front loading universal paper cassette Multi-feed bypass tray : 550 sheet × 2 (FP-D250/D350 Series) Paper capacity Cassette : 550 sheet × 1 (FP-D450/D600) Bypass : 50 sheets Copy size Ledger / A3 –...
Page 11 Special paper OHP, Label paper, Tracing paper (Through multi-feed bypass) <Copier Specifications> Resolution 600 dpi (FP-D250/D350 series) 400 dpi (FP-D450/D600) Gradation 256 steps (Photo Mode) 2 steps (Text/Photo Mode) First copy time 3.9 sec. (Letter/A4 size, without Auto mode) (FA-D250/D350 series) 3.2 sec.
Page 12 Resolution Max. 600 dpi (True) / 1200 dpi (Smoothing) Print speed 28 ppm (pages per minute) Letter / A4 (FP-D250) 35 ppm (pages per minute) Letter / A4 (FP-D350 series) 45 ppm (pages per minute) Letter / A4 (FP-D450) 50 ppm (pages per minute) Letter / A4 (FP-D600)
Page 13: Features
1. 2 Features <General Features> 1. Use of new digital technology 1) Optimum image quality is maintained for a long period in varying environmen- tal conditions with the use of Digital QUANTUM (QUARC) technology. Digital QUANTUM (QUARC): Digital Qualitative Reasoning Based Adaptive Controller.
Page 14 Faster print speed can be expected by speed of rasterrinsing process. When the image processing memory of the copier is 8 MB (FP-D250 : All, FP- D350 : except North America) : If the machine error often occurs when the high...
Page 15: New Functions
1. 3 New functions 1. Digital Skyshot Black edges are removed automatically, however if the original is not square to the original guide the copy may have some edges printed in black. 2. Page Number print. The page number can be automatically printed on each page. 3.
Page 16: System Configuration
FA-MA301 FA-HD01 System Stand FA-DS725 Paper drawer Kit FA-DS825 FA-DK10 DD Browser DD Filing Unit Software FA-WA01 (For FP-D250/D350/D350H) FA-WB10 Hard Disk Drive Mounting kit FA-WA02 (For FP-D450/D600) for Mirroring FA-PK30 FA-HD02 H/D (2GB) Personal Card x 10 pcs Inverting...
Page 17: Commonality Of Accessories
1. 5 Commonality of accessories Model Number FP-D250 FP-D350H FP-D450 Description Model number Remarks D350 D600 System Stand FA-DS725 System Stand FA-DS825 550 Sheet Paper FA-MA0555 Drawer Paper Drawer Kit for FA-DK10 Kit required for FA-MA0555 System Stand installation in bottom slot...
Page 18 Toner 20,000 copies (Letter/A4, FQ-TL20 6% density) Toner 24,000 copies (Letter/A4, FQ-TL24 6% density) Developer 120,000 copies (FP-D350) FQ-ZL20 80,000 copies (FP-D250) Consumables Developer 120,000 copies FQ-ZL30 120,000 copies (FP-D350/D450/D600) Drum FQ-HL20 80,000 copies (FP-D250) Waste Toner Bottle FQ-BA10 For use in FA-F350/F355...
Page 19 Model Number FP-D250 FP-D350H FP-D450 Description Model number Remarks D350 D600 DD Filing Unit FA-WA01 Standard DD Filing Unit FA-WA02 DD filing Personal Card FA-KP01 Standard Accessories DD Browser FA-WB10 Software DD Server Software FA-WS10 Hard Disk Drive for FA-HD02...
Page 20: Operation
STOP START OPERATION SWITCH START ORIGINAL SIZE STOP (D450/D600) COPY SIZE Ready Indicator Ready:GreenLED Not ready:RedLED Copy Reservation:FIashing FP-D250 / D350 / D450 / D600 (Printer, Filing, option) TOUCH PANEL DOCUMENT DISPLAY SAVE SORT/ USER MULTI-SIZE MANUAL ONLINE PRESET FINISH...
Page 21 FP-D250 / D350 / D450 / D600 (DD filing, option) TOUCH PANEL DOCUMENT DISPLAY SAVE SORT/ USER MULTI-SIZE MANUAL ONLINE PRESET FINISH FEED ENERGY DATA SAVER ADD PAPER INTERRUPT MULTI-SIZE SORT/ USER ENERGY FEED ADDPAPER ONLINE DATA FINISH PRESET SAVER...
Page 22: Component Location
1. 7 Component Location 1. Outer view Platen cover (option) Zip Drive (Option: FP-D250/ Control panel D350/D450/D600 Standard: FP-D350H) Operation Switch (D450/D600) Paper exit door Bypass Power switch (D450/D600 : inside of front door) Paper feed door Paper drawer / tray...
Page 23: Inner View
2. Inner view SV711 Fuser area cover Manual paper feed knob Toner bottle (Feed unit) Drum unit Paper transport handle Developer unit Transfer/Separation corona Toner hopper unit Paper transport unit Developer release lever Manual paper feed knob Waste toner bottle (Fuser unit) Total counter 1-14...
Page 24 Bypass pick-up roller Paper exit roller Bypass paper feed roller Paper exit sensor Bypass DFP roller Heat roller Middle roller Cleaning web roller Paper feed roller Full-speed unit home position sensor *Included with the ADU unit. (Option: FP-D250/D350/D350H, Standard: FP-D450/D600) 1-15...
Page 25: Fan/Motor Location (Fp-D250/D350/D350H)
3. Fan/Motor Location (FP-D250/D350/D350H) Optics fan Optics drive motor *Printer controller Developer Unit cooling fan cooling fan *Power supply cooling fan Exhaust fan Toner bottle motor Main motor Suction/ Dust collecting Ozone fan Lifting motor * ADU drive (upper stage)
Page 26: Fan/Motor Location (Fp-D450/D600)
4. Fan/Motor Location (FP-D450/D600) Optics fan Optics drive motor *Printer controller Developer Unit cooling fan cooling fan Power supply cooling fan Exhaust fan Toner bottle motor Main motor Suction/ Dust collecting Ozone fan ADU drive motor ADU paper Lifting motor length guide (lower stage) motor...
Page 27: Sensor Location
* ADU paper Paper detection Toner density D350H) detection (lower stage) Paper detention * ADU detection Paper level (lower stage) * ADU paper width Paper level (upper stage : D250/D350/D350H) * Included with the ADU unit. (Option: FP-D250/D350/D350H, Standard: FP-D450/D600) 1-18...
Page 28: Solenoid/Clutch/Discharge Lamp Location
Pick-up solenoid Door switch (upper stage : D250/D350/D350H) Laser unit Paper feed clutch switch (lower stage) Power switch * ADU clutch Pick-up solenoid (lower stage) Separation Recycle solenoid solenoid (FP-D450/D600) * Included with the ADU unit. (Option: FP-D250/D350/D350H, Standard: FP-D450/D600) 1-19...
Page 29: Pcb Location (Fp-D250/D350/D350H)
7. PCB Location (FP-D250/D350/D350H) *Control Touch panel panel D Control panel CPU Control CCD control panel B LVPS (Low voltage *Control panel C power supply) Control panel A Printer controller (option) AC driver *NAC System Control HVPS (High Automatic duplex...
Page 30: Hard Disk Drive/Zip Drive Location
9. Hard Disk Drive / Zip Drive Location *Zip drive *Hard disk for filing Hard disk for printer (Option) Hard disk for back-up (Option) *(Option: FP-D250/D350/D450/D600, Standard: FP-D350H) 1-21...
Page 31: Copy Process
Photo electric conversion Laser Exposure Original Cleaning Developer Toner (AC) (+DC) Separation Transfer Exit Fusing Paper feed (Option: FP-D250/D350/D350H, Standard: FP-D450/D600) Primary Charge: Image Exposure: Developing: Latent charge image Illumination Charge corona Toner (–) Drum Magnetic Aluminium Latent roller layer...
Page 32: Precautions With Consumables
1. 9 Precautions with Consumables Photoreceptor drum • Do not touch the surface (with the hand or anything else). • Stand the drum with the drum gear up for storage. • Be careful not to smear with saliva, water, oil and so on. •...
Page 33 5) Safety and hygiene Toner has the property of easily being wind blown. Toner on skin does not cause any health risk. However inhalation is undesirable even if a powder is simply dust. Therefore, be careful not to inhale toner. •...
Page 34: Digital Image Control Qualitative Reasoning Based Adaptive Controller
1. 10 Digital Image Control Qualitative Reasoning Based Adaptive Controller • Even if the toner density is at it's standard level, the copy image may vary with time depending on the characteristics of the drum and environmental variations. To prevent this change, the copy density sensor, which is installed to the left of the drum unit, controls the copy process to stabilize the image.
Page 35 a) During initialization. b) After every 1,000 sheets following execution of Qualitative Reasoning Based Adaptive Controller c) At 200 copies after turning power on. d) At 200 copies after replacing the toner bottle. • Copy density detecting sensor Two sensors for detection of copy density are used, one for halftone (line pattern) and one for black density.
Page 36 Digital QUANTUM (QUARC) System Scanner CCD gain adjustment White shading CCD gain adjustment Black shading Image density Sensor mark sheet Black level Sensor mark sheet CCD electrical adjustment Printer Laser power Electronic Pattern Grid Voltage Digital QUANTUM Copy density sensor (QUARC) White Control...
Page 37 Electronic Pattern Laser Power Laser Unit Halftone Black Grid Voltage Drum Copy density sensor Halftone Black sensor sensor Digital Sensor Halftone QUANTUM Output (QUARC) Black Control Control point High Density 1.25 Ideal Curve Middle Density 0.35 Density data from printer 1-28...
Page 38: Sub Assemblies
Section II Sub Assemblies 2.1 Main Drive The driving mechanism of this machine is as follows. Main motor Fuser unit Flywheel Pulley 1 Middle roller Pulley 2 clutch Transport roller Magnetic Bypass roller unit Drum Registration roller Paper feed unit Middle roller Middle gear Middle roller...
Page 39: Operation
2. 2 Operation 1. Sheet bypass paper feed 1) Construction of the sheet bypass paper feed unit The construction of the sheet bypass paper feed unit consists of a sheet bypass paper feed roller, transfer roller, paper pass sensor, DFP roller, and timing roller.
Page 40 2) Operation of sheet bypass paper feed unit (1) Paper feed operation • After choosing the sheet bypass tray and pressing the start key, the main motor is energized. The main motor drives to the transmission gears via the respective driving gears.
Page 41 Main motor Middle roller Pulley 1 clutch Pulley 2 Sheet bypass unit Paper feed roller Cleaning sheet DFP roller Middle Paper pass roller Middle Paper sensor (upper) gear detecting Registration sensor roller Middle roller (lower) Pick-up roller Registration roller clutch Registration roller gear Middle gear...
Page 42: Paper Feed Unit
2. Paper feed unit 1) Construction of paper feed unit • The construction of paper feed unit is as follows. Part description Functions Pick up roller Transfers the paper from paper feed cassette. Paper feed roller Feeds the paper. Paper feed solenoid Lowers the paper transfer roller to the paper.
Page 43 2) Paper feed unit operation • When the start key is pressed, the paper feed clutch turns ON. The drive from the main motor is transmitted to the idler gear through the respective gears and belts, rotating the idler gear which is connected to the middle roller clutch.
Page 44 3) Paper drawer lift mechanism • When the paper drawer is closed, the lift lever connects with the coupling which drives the machine side lift lever. Next, the lift motor rotates and it's drive is transmitted to the lift lever driving gear via the respective gears and rotates the lift lever to lift up the drawer bottom plate.
Page 45: Developer Unit
3. Developer unit 1) Construction of the developer unit • The developer unit consists of the magnet roller, sleeve, transport screw and mixing mill. • The developer is mixed and charged by the transport screw and the mixing mill where it is transferred to the developer sleeve. The developer on the sleeve forms a brush by the magnetic force of the magnetic roller, and makes contact with the electrostatic latent image on the drum.
Page 46 • Charge (developer bias) is applied to the magnetic roller sleeve, which prevents toner from moving to the non-image area of the drum. The distance between the drum and the sleeve is controlled by the drum spacers. FP-D250/D350 Series FP-D450 FP-D600 Amount of developer Approx.
Page 47 Reference: • The twin field magnetic roller provides enhanced developing performance by a wider developing area which results from two pole peaks (S1 and S2 pole) facing the drum surface. • N2 through S3: Attracts the developer to the sleeve from the mixing mill. •...
Page 48 4) Installing/removing the developer unit • Turning the Developer Release Lever clockwise rotates the Cam releasing the pressure between the Magnetic roller spacer and the Drum spacer. Accordingly the Developer Unit is released from the Drum. 2-11...
Page 49 5) Toner Density Control (TDC) sensor • The TDC sensor, which is installed under the developer transport screw, is an inductance type sensor used to detect the ratio of toner to carrier in the developer unit. The sensor measures changes of magnetic flux density, and monitors the toner density in this way.
Page 50 F8-09 start CPU will check toner density sensor output. (2.5 V) CPU will adjust sensor gain control signal Memory number will be changed to new number in memory. (F6-21 F6-26) Toner density sensor output voltage will be adjusted to 2.5 V (2) Maintain standard toner density By checking the output voltage of the TDC sensor for every copy, the timing of toner supply to the developer unit is controlled so that the output voltage is 2.5V...
Page 51 (Reference 1) Toner supply route Developer unit Reserve tank (hopper) Bottle (Reference 2) Forced toner supply Supply toner: supply for 6.7 seconds from reserve tank. (amount of toner supply: approx. 1.1 g) Perform twice. Rotate bottle for 7 seconds: supply toner to reserve tank. (Toner is not supplied to developer unit.) Note: Bottle rotation means toner is being added to the reserve tank, not the developer unit.
Page 52 7) Drum cleaning • After developing and transferring, the toner remaining on the drum is wiped away by the cleaning blade. • The cleaning blade touches the drum surface with a specific pressure applied by the blade pressure spring, and cleans the toner off the drum surface. •...
Page 53: Toner Hopper Unit
4. Toner hopper unit 1) Construction of the toner hopper • The construction of the toner hopper is as follows. Part description Function Toner bottle Supply toner. Home position sensor Detect the home position of toner bottle. Reserve tank After storing toner in toner hopper, supply to developer mixing unit.
Page 54 2) Supplying toner The Toner Hopper Unit supplies toner to the Developer Mixing Unit via the Reserve Tank. Toner addition is done in two stages, by turning the Toner Hopper Motor in: Forward Direction: The bottle turns (via a spring clutch) to supply toner from the Toner Bottle to the Reserve Tank.
Page 55 3) Toner level detection • When the toner volume sensor in the toner hopper detects no toner remaining, while the toner bottle is continuously rotating, the "Add toner" message will be displayed but the machine will continue to operate. However, if the toner concentration level falls below a specified level, a "U13"...
Page 56 D450/D600) the toner recycle system activates the toner recycle solenoid switching the machine from the recycle mode to the refresh mode. The machine will remain the refresh mode for the next 300 copies (FP-D250/ D350 Series)/200 copies (FP-D450/D600), during which time the contaminated toner is emptied into the toner waste bottle.
Page 57: Paper Transport Unit And Separation Unit
5. Paper transport unit and separation unit 1) Paper transport unit The paper transport unit transports the paper after transfer/separation. The paper is secured by the suction fan and transferred to the fuser via the transfer belt. • The paper transport unit is driven by the main motor which transfers drive to the paper transport drive gear via respective drive gears.
Page 58: Fuser Unit
Maintains pressure between heat and pressure roller. Heat roller temperature 374°F/190°C (D250/D350/D350H) 359°F/180°C(D450/D600) 7·8 Main heater lamp 850 W (FP-D250/D350) 950 W (FP-D450/D600) Sub heater lamp 400 W (Short one) (FP-D450/D600) Pressure roller tension Approx. 60 kgf (D250/D350/D350H) Approx. 46.4 kgf(D450/D600)
Page 59 2) Fusing • The fuser unit makes the image permanent by fusing the toner to the paper with heat and pressure. • The surface of the heat roller has excellent toner release characteristics and has been treated to enhance its durability and anti-static characteristics. •...
Page 60 Cleaning web roller Web drive gear Heat roller Web connecting gear Pressure roller Heat roller bearing Paper exit sensor lever Heat roller gear Fuser lamp Fuser coupling gear Middle gear 3) Driving of fuser unit • Drive for the fuser unit is provided by the main motor and is transmitted to the fuser coupling gear via the respective gears.
Page 61 5) Temperature control The heat for the heat roller is provided by a halogen lamp. The lamp turns on during the warm up cycle and periodically during copy operation to maintain the specified temperature. Sequence a)When the power to the copier is turned on the heater lamp is turned on and begins heating the heat roller.
Page 62 Solenoid 6) Exit/2 sided copy switching (Option: FP-D250/D350/D350H, Standard: FP-D450/D600) • When 2 sided copying is selected, paper exiting the fuser unit will be redirected to the ADU via the paper exit selection guide. The guide is activated by the exit solenoid, mounted on the rear frame of the copier.
Page 63: Optics Unit
7. Optics unit 1) Construction of optics unit • The optics unit consists of the exposure lamp (Xenon lamp), lens, CCD sensor, laser scanning unit (LSU) and reflector mirrors mounted on scanning assemblies. • While moving the full-speed unit and the half speed unit with the optics motor, the exposure lamp illuminates the original.
Page 64 Part description Function Full-speed unit Includes exposure lamp and No.1 mirror. It moves to scan the original. Half-speed unit Includes No.2 and No.3 mirrors. It scans at half speed of the full speed unit keeping the optical path length from the original to the lens constant. Optics cooling fan Cools the optics unit.
Page 65 4) Exposure lamp ON/OFF control (LPCNT1) Exposure lamp Main CPU PCB Lamp inverter (Xenon lamp) Lamp inverter control signal When the lamp inverter control signal (LPCNT1) of the main CPU PCB is at "L" level, the exposure lamp (Xenon lamp) is turned on at a high frequency by the lamp inverter.
Page 66 5) Driving optics unit • The optics unit (full-speed unit and half-speed unit) is driven by the optics unit motor. The optics unit motor revolution drives the full-speed unit and half-speed unit via optics unit motor belt, full-speed half-speed drive pulley, full-speed unit drive belt and half-speed unit drive belt.
Page 67 5) Laser scanning unit (LSU) (1) Outline Semiconductor laser 1 Synchronization sensor Collimating lens Mirror Lens Half mirror Semiconductor laser 2 Polygon mirror Collimating lens Mirror Mirror Mirror Main scan direction OPC Drum Sub scan direction • Divergent light from the semiconductor laser (exposure) with light intensity modulation by a digital image signal is converted into parallel light by a collimating lens.
Page 68 (2) Semiconductor Laser • The laser beams that emanate from two semiconductor lasers are turned ON/ OFF by turning the current flow to the semiconductor lasers ON/OFF with a digital signal that corresponds to the image to irradiate the drum. The semiconductor laser is switched ON/OFF in accordance with the image data.
Page 69 (5) f-θ lens • A lens that causes the parallel light reflected from the polygon scanner to fall on the drum. It is designed so that transmitted light curves toward the optical axis around the lens with a large scanning angle so that the incident light that swings at a constant angular velocity becomes a constant velocity scanning for the drum.
Page 70: Automatic Duplex Unit (Adu)
8. Automatic duplex unit (ADU) 1) Component location 14 13 12 21 Paper pass sensor A Paper weight lever Paper width guide Drive motor Connector Magnetic clutch ADU tray detecting sensor Clutch gear Paper width guide home position Paper width guide motor sensor Paper length guide motor Paper pass sensor...
Page 71 2) Mechanical operation 1 Paper stack/paper return operation When the drive motor rotates counterclockwise and turns gear 6 and the timing pully, the transfer roller rotates and paper is transported onto the transfer guide 2. At the same time the magnetic clutch turns ON and the storage roller rotates, paper is reversed and stored in the ADU.
Page 72 3 Paper Width guide operation When the paper width guide motor rotates and turns the timing belt, the paper width guides align paper. Operation timing for the paper width guide is shown below. 1)When the power : Move to Letter-R/A4R size position, after switch turns ON detecting paper width guide home position sensor.
Page 73 3) Operation flow chart Power switch ON Paper in ADU? Paper detected in ADU before power OFF? (Check memory for paper in ADU) Paper width/length guide no operation "Remove paper in ADU" indication Press reset key, paper feed out Jam indication Remove jam paper Open/close front door Allow paper width/length guide to Letter-R size...
Page 74: Preventive Maintenance
Section III Preventive Maintenance Preventive maintenance is performed at specific intervals and consists of machine cleaning and parts replacement. It is essential to perform these service activities properly and at the specified intervals for customer satisfaction. The purpose of this service is to maintain machine performance and image quality. 3.1 Precautions for Preventive Maintenance Service •...
Page 75 • Using a vacuum cleaner for the cleaning of the TDC sensor could cause electrostatic damage, therefore, use a blower brush or cotton swab for the cleaning of these parts. Before vacuuming the developer unit remove the TDC sensor. • When handling the drum, the precautions listed in section 1.9 “Precautions with consumables”...
Page 76: Precautions For Handling
(If the power switch is turned off, wait at 15 seconds before turning the power switch back on. If data in the hard disk or Zip disk should be destroyed on that time, Panasonic will not bear any responsibility.) When the digital copier is in operation, especially hard disk or Zip drive is in operation or just after the turning off the power switch (approx.
Page 77 Caution for Zip disk (1) In order to prevent lose of important data, keep backup disk.” (2) Be careful handling disk and observe the following points. • Do not disassemble the disk. Shutter • Do not open the shutter of the disk. •...
Page 78: Maintenance Chart
3.3 Maintenance chart 1. Replacement (For FP-D250) Item Service Part number Q'ty per Maintenance cycle (x 1000) unit Multi feed Paper feed roller(bypass) FFPMA05411 bypass Paper feed roller(Cassette) FFPMA05411 unit / DFP Roller(bypass) FFPMA05411 Paper feed DFP Roller(Cassette) FFPMA05411 unit...
Page 79 Item Service Part number Q'ty per Maintenance cycle (x 1000) unit Main Ozone filter 1 FFPHJ00472 body Ozone filter 2 FFPHJ0039 Ozone filter 4 FFPHJ0051 Discharge lamp PQ24V8.7WMG1 Transfer/Separation corona FFPVL01L01 Corona wire 1 FFPXL04H00 Replace at every 80,000 copies. Corona wire 2 FFPXL05H00 Replace at every 80,000 copies.
Page 80: Replacement (For Fp-D350/D350H)
2. Replacement (For FP-D350/D350H) Item Service Part number Q'ty per Maintenance cycle (x 1000) unit Multi feed Paper feed roller(bypass) FFPMA05411 bypass Paper feed roller(cassette) FFPMA05411 unit / DFP Roller(bypass) FFPMA05411 Paper feed DFP Roller(cassette) FFPMA05411 unit Pick-up roller(bypass) FFPMA0542 Pick-up roller(cassette) FFPMA0542 Cleaning sheet...
Page 81 Item Service Part number Q'ty per Maintenance cycle (x 1000) unit Main Ozone filter 1 FFPHJ00472 body Ozone filter 2 FFPHJ0039 Ozone filter 4 FFPHJ0051 Discharge lamp PQ24V8.7WMG1 Transfer/Separation corona FFPVL01L01 Corona wire 1 FFPXL04H00 Corona wire 2 FFPXL05H00 Dust protection filter FFPHJ0049 Drum Separation finger FFPLK0332...
Page 82: Replacement (For Fp-D450/D600)
3. Replacement (For FP-D450/D600) Item Service Part number Q'ty per Maintenance cycle (x 1000) unit Multi feed Paper feed roller(bypass) FFPMA05411 bypass Paper feed roller(cassette) FFPMA05411 unit / DFP Roller(bypass) FFPMA05411 Paper feed DFP Roller(cassette) FFPMA05411 unit Pick-up roller(bypass) FFPMA0542 Pick-up roller(cassette) FFPMA0542 Cleaning sheet...
Page 83 Transfer/Separation corona FFPVL01Q611 Corona wire 1 FFPXL04H00 Corona wire 2 FFPXL05H00 Dust protection filter FFPHJ0049 Drum Separation finger FFPLK0332 Paper feed roller FFPMA0558 FP-D250 Paper feed pad FFPKP00821 /D350 DFP roller FFPMA0559 /D350H F/R mylar FFPXD07J004 (Option) Storage roller FFPMA0557...
Page 84: Cleaning Method
3. 4 Cleaning Method • Cleaning method for each PM service visit is shown below. 24 23 3-11...
Page 85 Cleaning position Tool/solvent Work/precaution Sheet bypass paper - Use IPA, if toner is stuck on the Cloth with transfer roller rollers. (use sparingly) water / IPA - Do not use cotton for cleaning Sheet bypass paper feed roller Registration roller Middle roller Paper feed roller Pick up roller...
Page 86 Cleaning position Tool/solvent Work/precaution Blower Mirror (No.1 ~ 3) - Exercise caution when cleaning brush / otherwise the mirror surface may Glass get damaged cleaning - Clean with soft paper and IPA as Lens paper with required. Original size detecting Blower - Clean the dust off of the sensors.
Page 87: Disassembly
3. 5 Disassembly PM parts replacement procedure • The replacement procedure of PM parts is as shown below. Multi-feed bypass Fuser Unit Optics Unit 3-15 3-25 3-30 Main body 3-36 ADU middle roller unit 3-18 (Option) Paper feed 3-33 Unit 3-18 Developer Drum Unit...
Page 88: Multi-Feed Bypass
1. Multi-feed bypass Cycle D250 D350 D450 Item Part name D350H D600 Pick up roller 120K 120K 120K Paper feed roller 120K 120K 120K DFP roller 120K 120K 120K Registration roller 1080K 1080K 1080K Registration roller 1080K 1080K 1080K bearing Cleaning sheet 600K 600K 600K Caution...
Page 89 1) Removal of the pick-up roller/paper feed roller (1)Remove the right cover (2 screws) (2)Remove the screws and covers. (x 2) (3)Disconnect the harness. (4)Remove the bypass tray. (1)Remove the touch ring. (2)Remove the paper stopper. (3)Remove the sensor lever. (4)Remove the touch ring.
Page 90 3) Removal of the registration roller and cleaning sheet 1) Remove the right side and rear covers. 2) Open the front door. a) Remove the waste toner bottle. b) Swing the toner hopper open 180°. 3) Rotate the developer release knob clockwise. 4) Remove the drum unit.
Page 91: Paper Feed Unit
2. Paper feed unit Cycle Part name Item D250 D350 D450 D350H D600 Paper feed roller 120K 120K 120K Pick-up roller 120K 120K 120K DFP roller 120K 120K 120K Middle roller 1080K 1080K 1080K 3-18...
Page 92 1) Removal of the paper feed roller and the Pick-up roller 1) Remove the right side and rear cover. 2) Open the copier paper feed door. 3) Remove the paper feed door link. 4) Remove the copier paper feed door. Note: Move the link to the larger hole and remove.
Page 93 2) Removal of the DFP roller 1) Perform procedures 1 and 2. 2) Remove the lower roller cover (2 screws) 3) Remove the touch ring. 4) Remove the DFP roller. 3) Removal of the Middle roller 1) Perform procedures 1 and 2. 2) Remove the E ring gear on middle roller.
Page 94: Developer Unit
3. Developer unit Cycle Part name Item D250 D350 D450 D350H D600 Cleaning blade 120K 120K Drum 120K 120K Side seal (Front) 120K 120K Side seal (Rear) 120K 120K Corona charger 240K 360K 360K Developer 120K 120K Charge corona 120K 120K Toner dispersion 600K 600K 600K cover Magnetic roller...
Page 95 1) Removal of the cleaning blade 1) Open the front door. 2) Move the toner hopper to front side. 3) Rotate the developer release lever clockwise and remove the developer unit. 1) Remove the drum unit solenoid cover (1 screw). 2) Disconnect the harness.
Page 96 2) Removal of the Drum / Side seals 1) Perform procedures 1 and 2 and remove the drum unit. 2) Remove the drum cleaning blade tension spring. 3) Remove the front side screw on the drum shaft. 4) Remove the drum shaft and drum spacer (Front).
Page 97 4) Removal of the developer 1) Perform procedures 1 and 2. 2) Remove the developer unit and remove the mixer lid. 3) Dump the developer out of the unit. Note: Before vacuuming the developer unit remove the TDC sensor. 4) Vacuum any remaining developer on the magroller and inside of the developer unit.
Page 98: Fuser Unit
4. Fuser unit Cycle Item Part name D250 D350 D450 D350H D600 Cleaning web roller 120K 120K 120K Fuser lamp 240K 240K 240K Heat roller 240K 240K 360K Heat roller bearing 600K 600K 600K Heat-insulating bushing 360K 360K 360K Heat roller gear 600K 600K 600K Thermistor 240K 240K 240K...
Page 99 1) Removal of cleaning web (1) Open the front door. (2) Swing the toner hopper to the right. (3) Remove the fuser unit manual paper feed knob. (1 screw reverse threaded) (4) Remove the front cover. a) Remove the band. b) Remove the hinge pins.
Page 100 2) Removal of the fuser lamp/heat roller/heat roller bearing/insulating bushing/heat roller gear • Perform procedures 1and 2. (1)Remove the screws (x 4) (2)Remove the heat insulating cover. Note: Loosen pressure screws (x 2) FP-D250/ (1)Remove the spring. D350/D350H (2)Open the fuser lamp cover. 850 W (3)Remove the fuser lamp.
Page 101 3) Removal of the thermistor • Perform procedure 5. (1) Remove the two screws. (2)Remove the thermistor. SV507 4) Removal of the separation fingers (upper/lower) (1)Open the fuser exit door. (2)Remove the screws (x 2). (3)Remove the separation finger (upper) bracket.
Page 102 (4)Remove the springs. (5)Turn the separation fingers and remove them. SV506 5) Removal of the pressure roller/roller bearings • Remove the heat roller (refer to step 5 to • Remove the upper / lower separation finger brackets (refer to 10 and 11). Note: Mark the current height adjustment to use as a reference during re- assembly.
Page 103: Optics Unit
5. Optics unit Cycle Item Part name D250 D350 D450 D350H D600 Exposure lamp 720K 720K 720K 3 4 5 Filter A 120K 120K 120K Full speed unit drive belt Half speed unit drive belt Optics drive belt : As required 3-30...
Page 104 1) Removal of exposure lamp (1)Enter the service mode. (2)Perform F8-00 (3)Remove top right cover. (2 screws) (4)Remove two screws on the original guide plate. Note: When the conductive platen glass is installed, the grounding plate screw must also be removed. (5)Remove platen glass with original guide plate.
Page 105 2) Removal of dust filter A (1)Remove the platen cover (or Sheet Feeder/I-ADF if installed). (2)Remove the top rear cover (2 screws). (3)Disconnect the lattice connectors of any options (System Console and LCC). (4)Remove the rear cover (4 screws). Peel off the filter A and replace them with new ones.
Page 106: Automatic Duplex Unit (Adu) (Option)
6. Automatic duplex unit (ADU) (Option) Item Part name Cycle Paper feed roller Storage roller F/R mylar Paper feed pad DFP roller : Actual number of duplex copies mode (F7-09) 3-33...
Page 107 1) Removal of the paper feed roller/storage roller/F/R mylar/feed roller pad (1) Pull out the ADU until it stops. (2) Remove the upper cover (2 screws). (3) Open the transport guides (1 and 2). (4) Remove the screws (x 2). (5) Remove the stopper plate.
Page 108 (1)Perform procedure 1. (2)Open transport guides 1 and 2. (3)Peel off the paper feed pad and replace. Removal of the DFP roller (1)Perform procedure 1. (2)Remove the screws (x 2). (3)Remove the DFP roller block. (1)Remove the touch rings (x 2). (2)Remove the bearing.
Page 109: Main Body
7. Main body Cycle Item Part name D250 D350 D450 D350H D600 Corona wire 1 120K 120K 10•11 Corona wire 2 120K 120K Ozone filter 2 240K 240K 240K 4•8 Ozone filter 1 240K 240K 240K Dust protec filter 120K 120K (Main body) Transfer corona 240K 360K 360K Discharge lamp 240K 240K 240K...
Page 110 1) Removal of the corona wire (1)Open the front door. (2)Turn the transport lever and lower the transport unit. (3)Press down the transfer corona unit and draw it toward you. (1)Remove the paper guide. (2 screws) (2)Remove the corona covers. (front and rear) (1)Remove the corona wire spring.
Page 111 Ozone filters (2)Open the exit door. (3)Remove the filter holder (2 screw). (4)Remove the ozone filter 1and 4. (Ozone filter 4 : FP-D250/D350/D350H) Only FP-D450/D600 (1)Perform the procedures of the fuser unit Toner hopper unit removal and remove the fuser unit.
Page 112 3) Removal of the dust collecting filter (1)Remove the copier rear and right side covers. (2)Remove the dust collecting fan motor block. (3)Remove the dust collecting filter. 4) Replacement of the discharge lamp. (1)Open the front door. (2)Swing open the toner hopper 180°. (3)Remove 1 screw.
Page 113: Removal Of Back Up Battery
3.6 Removal of back up battery The Nickel-Cadmium Battery, under various state and local laws is recyclable and it may be illegal to dispose of the battery into municipal waste streams. Check with your local solid waste officials for details area for recycling options or proper disposal. Location Procedure Check...
Page 114: Adjustment
3. 7 Adjustment 3-41...
Page 115: Exposure Standard Adjustment
1. Exposure Standard Adjustment Location Procedure • The following values will be added to the reference value. DO NOT adjust these codes in the field. F6-17 : Grid standard voltage compensation F6-18 : Laser power compensation F6-19 : Developer bias standard voltage compensation (1) Enter the F6 mode.
Page 116: Copy Density Sensor Contamination Adjustment
2. Copy density Sensor contamination adjustment Location Procedure • The following adjustment is required when the drum is replaced. (1) Remove the old drum from the drum housing. (2) Clean the Image Density Sensor with a blower brush or Q-tip. (3) Install the new drum.
Page 117: Skew / Side To Side Adjustments (Printer Section)
3. Skew / Side to side Adjustments (Printer Section) Location Procedure Skew adjustment If skew of the copy is experienced and adjustment of the cassette has not proved effective, follow the procedure described below. (1) Place Ledger/A3 size paper in the sheet bypass tray.
Page 118 Location Procedure Side to side adjustment (Manual Procedure) Screw (1) Perform steps 1-3 in the Skew adjustment section. (Page 3-44) (2) Adjust the position of the sheet bypass guide to achieve proper side to side registrasiton. (3) Adjust the position of the cassette front Sheet by-pass tray cover to achieve proper side to side registration.
Page 119: Skew / Registration Adjustments (Scanner Section)
Location Procedure (3) Adjust F6-84 as necessary using the steps Contents Function outlined below. Move 2.0 mm to the left (4) If the distance between the left edge of Move 1.5 mm to the left the paper and the nearest black line is less Move 1.0 mm to the left than 5 mm input a positive number, using Move 0.5 mm to the left...
Page 120: Lead Edge / Trail Edge Void Adjustment (Printer Section)
Location Procedure Registration Adjustment (1)Make a copy of Test Chart 53/54. (2)For adjustment of lead edge registration when making a copy off the platen glass, use F6-05. (To advance the registration, input a more (+) number) (3)For adjustment of lead edge registration when making a copy using the FA-A888, F6-36 to achieve proper...
Page 121: Laser Power (Pwm Circuit)
6. Laser power (PWM circuit) adjustment Note : This adjustment is required only when the Laser unit has been replaced. Location procedure 1)Place Ledger/A3 size paper in the sheet bypass tray. 2)Enter the service mode and select (-5) mode " 8 ". 3)Select F8-18 and press the Start key...
Page 122: Signal Information
Section IV PCB Connector and Signal Information 4. 1 Glossary of electrical abbreviations Signal Name Function AC 120V / AC 220 - 240V power supply AC 120V / AC 220 - 240V power supply ADFIN ADF original feed completed signal ADFOUT ADF original feed control signal ADFRRSN...
Page 123 Signal Name Function DC+24V power supply CRRSN1 Paper detecting signal CRRSN2 Paper detecting signal Total counter count signal DDFM Developer cooling / Dust collection fan motor ON / OFF signal DOSN Front door Open/Close detecting signal DSAC1 AC 120V / AC 220 - 240V power supply DXLA Motor drive signal A DXLAB...
Page 124 Signal Name Function EXFM2 Grid bins adgustment signal Exhaust fan motor 2 ON / OFF signal Hard disk cooling fan motor lock F signal EXFM3 Exhaust fan motor 3 ON / OFF signal EXFM4 Exhaust fan motor 4 ON / OFF signal EXFM5 Exhaust fan motor 5 ON / OFF signal (FP-D450/D600) Ground...
Page 125 Signal Name Function LBSN1 Paper upper limit detecting signal LBSN2 Paper upper limit detecting signal LEMTEM1 Laser A PWM mode change signal LEMTEM2 Laser B PWM mode change signal Optics motor drive signal A LMAB Optics motor drive signal A Optics motor drive signal B LMBB Optics motor drive signal B...
Page 126 Signal Name Function PMLOCK Polygon motor lock detecting signal PMVP DC+24V power supply PNL_RST Control panel reset signal PRCFL Printer controller fan motor lock F signal PRCFM Printer controller fan motor ON/OFF signal PSAC1 AC 120V / AC 220 - 240V power supply PSAC2 AC 120V / AC 220 - 240V power supply PSFL...
Page 127 Signal Name Function VCDS Sensor ON/OFF signal DC+5V power supply DC+24V power supply VTED Add toner sensor ON/OFF signal ZCRS Zero cross Signal...
Page 128: Main Cpu Pcb (Fp-D250/D350 Series)
4.2 Main CPU PCB (FP-D250/D350 Series) (FP-D250/D350 Series) (CN1) Signal Destination Status Function Name LVPS PCB Scanner 24V ON/OFF SVCNT CN17-7 signal LVPS PCB Printer 24 V ON/OFF PVCNT CN17-6 signal Pulse LVPS PCB ZCRS Zero cross Signal CN17-5 LVPS PCB...
Page 129 (CN2) (FP-D250/D350 Series) Signal Destination Status Function Name Bypass paper size sensor 3 DC+5Vpower supply CN-1 Bypass paper Paper size detecting Detect size sensor 3 signal 3 HSSN3 CN-2 Bypass paper size sensor 3 Ground CN-3 Bypass paper size sensor 2...
Page 130 (CN3) (FP-D250/D350 Series) Signal Destination Status Function Name Copy density Ground sensor CN-1 Copy density Analog Paper base tone CDSN2 sensor CN-2 0–5V detecting signal Copy density VCDS Sensor ON/OFF signal sensor CN-3 Copy density Analog Copy density detecting CDSN1 sensor CN-4 0–5V...
Page 131 (CN5) (FP-D250/D350 Series) Signal Status Function Destination Name Main motor PGND Power ground CN-1 Main motor Main motor drive control MMCNT CN-2 signal Stop Rotate Main motor lock Main motor MMLCK CN-3 detecting signal Main motor Pulse MMCLK Main motor clock signal...
Page 132 (CN6) (FP-D250/D350 Series) Signal Destination Status Function Name Exhaust fan 4 Exhaust fan motor 4 CN-1 ON/OFF signal EXFM4 Dust collection Dust collection fan fan motor CN-1 motor ON/OFF siganl DDFM Exhaust fan 4 Exhaust fan motor 4 Stop Rotate...
Page 133 (CN7) (FP-D250/D350 Series) Signal Destination Status Function Name System console 32 bit data transfer PCB CNSQ-23 output signal Pulse F32BOUT or LCC driver PCB CN562-5 System console 32 bit data transfer PCB CNSQ-27 enable signal FENB or LCC driver PCB CN562-6...
Page 134 (CN8) (FP-D250/D350 Series) Signal Destination Status Function Name Inverting shift Pulse tray PCB F32AOUT 32 bit data output signal CN601-5 Inverting shift 32 bit data transfer data tray PCB enable signal FENB CN601-6 Inverting shift 32 bit data transfer latch...
Page 135 (CN9) (FP-D250/D350 Series) Signal Destination Status Function Name LVPS +12V12 DC+12V power supply CN10-1 LVPS AGND Ground CN10-2 LVPS Ground CN10-3 LVPS Ground CN10-4 LVPS DC+5V power supply CN10-5 LVPS DC + 5V power supply CN10-6 (CN10) (FP-D250/D350 Series) Signal...
Page 136 (CN11) (FP-D250/D350 Series) Signal Destination Status Function Name ADU driver PCB PGND Power ground CN651-2 ADU driver PCB DC+24V power supply CN651-1 ADU driver PCB PGND Power ground CN651-4 ADU driver PCB DC+24V power supply CN651-3 ADU driver PCB Pulse...
Page 137 ADU driver PCB Detecting ADUSL ADU detecting signal CN2-24 — — — — ADU driver PCB Ground CN2-22 (FP-D250/D350 Series) (CN12) Signal Destination Status Function Name Exhaust fan 1 PGND Power ground CN-3 Exhaust fan 1 Exhaust fan motor 1...
Page 138 Signal Destination Status Function Name Pulse Toner bottle Toner bottle motor drive BMBB motor CN-1 signal B Toner bottle DC+24V power supply motor CN-2 Pulse Toner bottle motor drive Toner bottle motor CN-3 signal B Pulse Toner bottle Toner bottle motor drive BMAB motor CN-4 signal A...
Page 139 (CN13) (FP-D250/D350 Series) Signal Destination Status Function Name Platen cover open / close Ground sensor CN-3 Platen cover Platen cover open / Close Open open / close close detecting signal PCSN sensor CN-2 Platen cover open / close DC+5V power supply...
Page 140 (CN15) (FP-D250/D350 Series) Signal Destination Status Function Name Finisher Inverse sorter receive Pulse ISTRX connector CN-8 signal Finisher Pulse STRX Sorter receive signal connector CN-9 Finisher Ground connector CN-10 Finisher Inverse sorter transfer Pulse ISTTX connector CN-11 signal Finisher Pulse...
Page 141 (CN17) (FP-D250/D350 Series) Signal Destination Status Function Name Optics fan PGND Power ground CN-3 Optics fan Stop Rotate Optics fan motor lock LPFL CN-2 detecting signal Optics fan Optics fan motor ON / LPFM CN-1 OFF signal Exposure lamp inverter PCB...
Page 142 (CN19) (FP-D250/D350 Series) Signal Destination Status Function Name ADF connector Inverse ADF receive Pulse IADFRX CN-8 signal ADF connector Pulse ADFRX ADF receive signal CN-9 ADF connector Ground CN-10 ADF connector Inverse ADF transfer Pulse IADFTX CN-11 signal ADF connector...
Page 143 (CN20) (FP-D250/D350 Series) Signal Destination Status Function Name Original size sensor 1 DC+5V power supply CN-1 Original size Original size detecting sensor 1 AOSS1 sensor signal 1 CN-2 Original size Original size detecting sensor 1 AOS1 sensor optics signal 1...
Page 144 Signal Destination Status Function Name Original size Original size detecting sensor 4 sensor optics signal 4 AOS4 CN-3 Original size sensor 4 Ground CN-4 Original size sensor 5 DC+5V power supply CN-1 Original size Original size detecting sensor 5 sensor signal 5 AOSS5 CN-2 Original size...
Page 145 (CN22) Signal (FP-D250/D350 Series) Destination Status Function Name Paper feed clutch DC+24V power supply (Upper stage) CN-1 — — — — Paper feed Paper feed clutch ON / clutch OFF signal PFCR1 (Upper stage) CN-2 — — — — Paper level...
Page 146 Paper detecting signal (Upper stage) CN-2 Paper upper limit sensor Ground (Upper stage) CN-3 Paper detecting sensor Ground (Upper stage) CN-3 (CN23) (FP-D250/D350 Series) Signal Destination Status Function Name Paper feed clutch DC+24V power supply (Lower stage) CN-1 — — —...
Page 147 Signal Destination Status Function Name Paper pass sensor DC+5V power supply (Lower stage) CN-1 Paper level Paper level detecting sensor signal PEWSN2 (Lower stage) CN-2 Paper pass Detecting sensor CRRSN2 Paper detecting signal (Lower stage) CN-2 Paper level sensor Ground (Lower stage) CN-3 Paper pass...
Page 148 (CN24) (FP-D250/D350 Series) Signal Destination Status Function Name LVPS PGND Power ground CN11-1 LVPS PGND Power ground CN11-2 LVPS PGND Power ground CN11-3 LVPS PGND Power ground CN11-4 LVPS DC+24V power supply CN11-5 LVPS DC+24V power supply CN11-6 LVPS DC+24V power supply...
Page 149 (CN25) (FP-D250/D350 Series) Signal Destination Status Function Name ADF timing sensor input Detecting signal ADFRRSN CN952-7 32 bit data receive input signal ADFIDI CN952-6 Ground CN952-9 32 bit data transfer / Pulse receive clock signal ADFICLK CN952-4 Data output enable...
Page 150 (CN27) (FP-D250/D350 Series) Signal Destination Status Function Name Lift motor Motor rotation control (Lower stage) signal (Upper direction) LUM2-1 CN-1 Lift motor Motor rotation control (Lower stage) signal (Lower direction) LUM2-2 CN-2 (FP-D250/D350 Series) (CN28) Signal Destination Status Function Name...
Page 151 (CN29) (FP-D250/D350 Series) Signal Destination Status Function Name Bypass paper feed clutch DC+24V power supply CN-1 Bypass paper Bypass paper feed feed clutch clutch ON / OFF signal HFCR CN-2 Registration roller clutch DC+24V power supply CN-1 Registration Registration roller clutch...
Page 152 CN-2 — — — — Registration roller paper Ground pass sensor CN-3 (CN30) (FP-D250/D350 Series) Signal Destination Status Function Name Paper exit DC+24V power supply solenoid CN-1 Paper exit Paper exit solenoid ON / PCSOL solenoid CN-2...
Page 153 (CN31) (FP-D250/D350 Series) Signal Destination Status Function Name Pulse Optics motor Optics motor drive LMBB CN-11 signal B Optics motor DC+24V power supply CN-9 Pulse Optics motor Optics motor drive CN-7 signal B Pulse Optics motor Optics motor drive LMAB...
Page 154 (CN36) (FP-D250/D350 Series) Signal Destination Status Function Name LSU pin photo sensor DC+5V power supply CN-4 LSU pin photo sensor Ground CN-3 LSU pin photo LSU main scan Pulse sensor synchronization signal LSULSYNC CN-2 LSU pin photo sensor Ground CN-1...
Page 155 (CN38) (FP-D250/D350 Series) Signal Destination Status Function Name LSU image data control PCB Ground CN1-a26 LSU image data Image picture element Pulse control PCB clock signal LCLKO CN1-a25 LSU image data control PCB Ground CN1-a24 LSU image data Pulse control PCB...
Page 156 Signal Destination Status Function Name LSU image data control PCB Ground CN1-a12 LSU image data Pulse control PCB LDA1 Laser A image data bit 1 CN1-a11 LSU image data control PCB Ground CN1-a10 LSU image data Pulse control PCB LDA0 Laser A image data bit 0 CN1-a9 LSU image data...
Page 157 Signal Destination Status Function Name LSU image data control PCB Ground CN1-b24 LSU image data control PCB +5VL DC+5V power supply CN1-b23 LSU image data control PCB +5VL DC+5V power supply CN1-b22 LSU image data Pulse control PCB LDB7 Laser B image data bit 7 CN1-b21 LSU image data control PCB...
Page 158 LSU image data control PCB Ground CN1-b2 LSU image data Laser B APC control Pulse control PCB signal ADJ2 CN1-b1 (CN39) (FP-D250/D350 Series) Signal Destination Status Function Name Developer cooling fan Developer DDFM ON / OFF signal cooling fan CN-1 Stop...
Page 159 (CN43) (FP-D250/D350 Series) Signal Destination Status Function Name LVPS cooling fan motor PGND Power ground CN-3 LVPS cooling LVPS cooling fan motor Stop fan motor lock F signal PSFL Rotates CN-2 LVPS cooling LVPS cooling fan motor fan motor ON / OFF signal...
Page 160 (CN201) (FP-D250/D350 Series) Signal Destination Status Function Name System control COM2 data terminal DTR2J PCB CN3-A01 ready signal System control +12V1 DC+12V power supply PCB CN3-A02 System control RTS2J COM2 request signal PCB CN3-A03 Pulse System control COM2 communication RxD2J...
Page 161 Signal Destination Status Function Name System control PCI bus address data AD24 PCB CN3-A25 signal System control 3.3V +3.3V DC+3.3V power supply PCB CN3-A27 System control PCI bus address data AD22 PCB CN3-A28 signal System control PCI bus address data AD20 PCB CN3-A29 signal...
Page 162 Signal Destination Status Function Name System control PCI bus address data AD13 PCB CN3-A46 signal System control PCI bus address data AD11 PCB CN3-A47 signal System control Ground PCB CN3-A48 System control PCI bus address data AD09 PCB CN3-A49 signal System control Bus command / byte C/-BE0...
Page 163 Signal Destination Status Function Name System control DC+5V power supply PCB CN3-B06 Pulse System control Interrupt request signal INTA PCB CN3-A06 Pulse System control Interrupt request signal INTC PCB CN3-A07 System control Ground PCB CN3-B12 System control Ground PCB CN3-B13 System control Ground PCB CN3-B15...
Page 164 Signal Destination Status Function Name System control PCI bus address data AD19 PCB CN3-B30 signal System control 3.3V +3.3V DC+3.3V power supply PCB CN3-B31 System control PCI bus address data AD17 PCB CN3-B32 signal System control Bus command / byte C/-BE2 PCB CN3-B33 enable signal...
Page 165 Signal Destination Status Function Name System control PCI bus address data AD08 PCB CN3-B52 signal System control PCI bus address data AD07 PCB CN3-B53 signal 3.3V System control +3.3V DC+3.3V power supply PCB CN3-B54 System control PCI bus address data AD05 PCB CN3-B55 signal...
Page 166 (CN203) (FP-D250/D350 Series) Signal Destination Status Function Name Printer controller Ground PCB CNJ5-1 Printer controller Ground PCB CNJ5-2 Printer controller Ground PCB CNJ5-3 Printer controller Ground PCB CNJ5-4 Printer controller Ground PCB CNJ5-5 Printer controller Ground PCB CNJ5-6 Printer controller...
Page 167 Signal Destination Status Function Name Printer controller Ground PCB CNJ5-20 Printer controller Ground PCB CNJ5-21 Printer controller Ground PCB CNJ5-22 Printer controller Ground PCB CNJ5-23 Printer controller Ground PCB CNJ5-24 Printer controller Ground PCB CNJ5-25 Printer controller Ground PCB CNJ5-26 Printer controller Ground PCB CNJ5-27...
Page 168 Signal Destination Status Function Name Printer controller Image data 5 PCB CNJ5-40 Printer controller Image data 6 PCB CNJ5-41 Printer controller Image data 7 PCB CNJ5-42 Printer controller Ground PCB CNJ5-43 Printer controller Image data 8 PCB CNJ5-44 Printer controller Image data 9 PCB CNJ5-45 Printer controller...
Page 169 Printer controller serial /SCPRN PCB CNJ5-58 data control signal Printer controller Ground PCB CNJ5-59 Printer controller Reset signal /RESET PCB CNJ5-60 (CN204) (FP-D250/D350 Series) Signal Destination Status Function Name 3.3V LVPS PCB 3.3V DC+3.3V power supply CN21-1 LVPS PCB Ground...
Page 170 (CN205) (FP-D250/D350 Series) Signal Destination Status Function Name Control panel Control panel CPU PCB communication receive P_RTS CN401-11 control signal Control panel Control panel CPU PCB communication transfer P_CTS CN401-12 control signal Control panel Control panel Pulse CPU PCB communication receive...
Page 171 (CN209) (FP-D250/D350 Series) Signal Destination Status Function Name CCD PCB CN801-23 Ground CCD PCB CN801-24 Ground CCD PCB Scanner horizontal Pulse CN801-21 synchronization signal SLSYNC_C CCD PCB CN801-22 Ground CCD PCB Return horizontal Pulse CN801-19 synchronizing signal RLSYNC differential output...
Page 172 Signal Destination Status Function Name CCD PCB Scanner image data 3 Pulse CN801-9 bit differential output SVD3 signal CCD PCB Inverse scanner image Pulse CN801-10 data 3 bit differential ISVD3 output signal CCD PCB Scanner image data 4 Pulse CN801-7 bit differential output SVD4 signal...
Page 173 (FP-D250/D350 Series) (CN210) Signal Destination Status Function Name CCD PCB Ground CN803-7 CCD PCB Ground CN803-8 CCD PCB Pulse Scanner D/A converter DA_DATA CN803-5 data CCD PCB Ground CN803-6 Pulse CCD PCB Scanner D/A converter DA_CLK CN803-3 clock CCD PCB...
Page 174: System Control Pcb (Fp-D250/D350 Series)
4.3 System Control PCB (FP-D250/D350 Series) (CN1 - CN2) Not used (FP-D250/D350 Series) (CN3) Signal Destination Status Function Name Main CPU PCB COM2 data terminal ready DTR2J CN201-1 signal Main CPU PCB +12V DC+12V power supply CN201-2 Main CPU PCB...
Page 175 Signal Destination Status Function Name Riser card PCB GNT0 Grant signal CN601-17 Main CPU PCB Ground CN201-18 — — — — Main CPU PCB AD30 PCI bus address data signal CN201-20 3.3V Main CPU PCB +3.3V DC+3.3V power supply CN201-21 Main CPU PCB AD28 PCI bus address data signal...
Page 176 Signal Destination Status Function Name Main CPU PCB Ground CN201-37 Pulse Main CPU PCB STOP Stop signal CN201-38 3.3V Main CPU PCB +3.3V DC+3.3V power supply CN201-39 Pulse Main CPU PCB SDONE Snoop done signal CN201-40 Pulse Main CPU PCB Snoop back off signal CN201-41 Main CPU PCB...
Page 177 Signal Destination Status Function Name Main CPU PCB PCI bus address data signal AD02 CN201-57 Main CPU PCB AD00 PCI bus address data signal CN201-58 Main CPU PCB DC+5V power supply CN201-59 — — — — Main CPU PCB DC+5V power supply CN201-61 Main CPU PCB DC+5V power supply...
Page 178 Signal Destination Status Function Name Main CPU PCB Ground CN201-115 Main CPU PCB Pulse CLKB PCI bus clock B CN201-116 Main CPU PCB Ground CN201-117 Pulse Riser card PCB REQ0 DMA transfer request signal CN601-118 Main CPU PCB DC+5V power supply CN201-119 Main CPU PCB AD31...
Page 179 Signal Destination Status Function Name Pulse Main CPU PCB IRDY Initiator ready signal CN201-135 Main CPU PCB 3.3V +3.3V DC+3.3V power supply CN201-136 Pulse Main CPU PCB DEVSEL Device select signal CN201-137 Main CPU PCB Ground CN201-138 Pulse Main CPU PCB LOCK Lock signal CN201-139...
Page 180 Signal Destination Status Function Name Main CPU PCB AD05 PCI bus address data signal CN201-155 Main CPU PCB AD03 PCI bus address data signal CN201-156 Main CPU PCB Ground CN201-157 Main CPU PCB AD01 PCI bus address data signal CN201-158 Main CPU PCB DC+5V power supply CN201-159...
Page 181 (CN4) (FP-D250/D350 Series) Signal Destination Status Function Name SO DIMM PCB Ground CN301-1 SO DIMM PCB 3.3V DRAM data bus signal CN301-2 SO DIMM PCB 3.3V DRAM data bus signal CN301-3 SO DIMM PCB 3.3V DRAM data bus signal CN301-4 SO DIMM PCB 3.3V...
Page 182 Signal Destination Status Name SO DIMM PCB 3.3V DRAM data bus signal CN301-21 SO DIMM PCB 3.3V DRAM data bus signal CN301-22 SO DIMM PCB 3.3V DQ10 DRAM data bus signal CN301-23 SO DIMM PCB 3.3V DQ11 DRAM data bus signal CN301-24 SO DIMM PCB 3.3V...
Page 183 Signal Destination Status Function Name Pulse SO DIMM PCB Column address control CAS2 CN301-41 signal Pulse SO DIMM PCB Column address control CAS3 CN301-42 signal Pulse SO DIMM PCB Column address control CAS1 CN301-43 signal SO DIMM PCB RAS0 Row address control signal CN301-44 Pulse SO DIMM PCB...
Page 184 Signal Destination Status Function Name SO DIMM PCB 3.3V +3.3V DC+3.3V power supply CN301-61 SO DIMM PCB 3.3V DQ29 DRAM data bus signal CN301-62 SO DIMM PCB 3.3V DQ30 DRAM data bus signal CN301-63 SO DIMM PCB 3.3V DQ31 DRAM data bus signal CN301-64 SO DIMM PCB —...
Page 185 (CN5) (FP-D250/D350 Series) Signal Destination Status Function Name 16 M Flash DIMM PCB Ground CN351-1 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-2 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-3 16 M Flash Flash memory address 3.3V...
Page 186 Signal Destination Status Function Name 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-15 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-16 16 M Flash Pulse DIMM PCB RD/BY Ready / busy check signal CN351-17 16 M Flash Write protection control...
Page 187 Signal Destination Status Function Name 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-29 16 M Flash 3.3V DIMM PCB +3.3V DC+3.3V power supply CN351-30 16 M Flash DIMM PCB — — — CN351-31 16 M Flash Flash memory address 3.3V DIMM PCB...
Page 188 Signal Destination Status Function Name 16 M Flash DIMM PCB — — — CN351-43 16 M Flash DIMM PCB — — — CN351-44 16 M Flash DIMM PCB — — — CN351-45 16 M Flash DIMM PCB — — — CN351-46 16 M Flash Flash memory address...
Page 189 Signal Destination Status Function Name 16 M Flash Flash memory data bus 3.3V DIMM PCB signal CN351-57 16 M Flash Flash memory data bus 3.3V DIMM PCB signal DQ11 CN351-58 16 M Flash Flash memory data bus 3.3V DIMM PCB signal CN351-59 16 M Flash...
Page 190 Signal Destination Status Function Name 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-71 16 M Flash DIMM PCB Ground CN351-72 4-69...
Page 191 (CN14) (FP-D250/D350 Series) Signal Destination Status Function Name 3.3V 3.3V LVPS CN20-1 DC+3.3V power supply LVPS CN20-2 Ground LVPS CN20-3 Ground 5.1V LVPS CN20-4 DC+5.1V power supply LVPS CN20-5 Ground 12V1 LVPS CN20-6 DC+12V power supply LVPS CN20-7 Ground –12V1...
Page 192: Control Panel Pcb (Fp-D250/D350 Series)
4.4 Control Panel PCB (FP-D250/D350 Series) 1. Control Panel CPU PCB (FP-D250/D350 Series) (FP-D250/D350 Series) (CN401) Signal Destination Status Function Name Main CPU PCB DC+5V power supply CN205-11 Main CPU PCB DC+5V power supply CN205-12 Main CPU PCB Ground CN205-9...
Page 193 (CN402) (FP-D250/D350 Series) Signal Destination Status Function Name Touch panel An abscissa detecting Select PCB CN-1 signal 1 Analog touch Touch panel An ordinate detecting PCB CN-2 signal 2 Analog touch Touch panel An abscissa detecting PCB CN-3 signal 2...
Page 194 (CN404) (FP-D250/D350 Series) Signal Destination Status Function Name LCD backlight INV1 Ground CN-1 LCD backlight AC voltage Approx. 1kVP-P INV2 CN-2 4-73...
Page 195 (CN406) (FP-D250/D350 Series) Signal Destination Status Function Name Control panel PCB A Ground CN357-15 Control panel PCB A DRV0 LED drive signal 0 CN357-16 Control panel PCB A DRV1 LED drive signal 1 CN357-13 Control panel PCB A DRV2 LED drive signal 2...
Page 196 (CN407) (FP-D250/D350 Series) Signal Destination Status Function Name Control panel Key input matrix circuit PCB A data signal 15 MTRKEY15 CN356-13 Control panel Key input matrix circuit PCB A data signal 14 MTRKEY14 CN356-14 Control panel Key input matrix circuit...
Page 197 (CN408) (FP-D250/D350 Series) Signal Destination Status Function Name Control panel PCB B Ground CN351-9 Control panel Key input matrix circuit PCB B data signal 6 MTRKEY6 CN351-10 Control panel Key input matrix circuit PCB B data signal 7 MTRKEY7 CN351-7...
Page 198: Control Panel Pcb A (Fp-D250/D350 Series)
2. Control Panel PCB A (FP-D250/D350 Series) (CN354 - CN355) Not used 4-77...
Page 199 (CN356) (FP-D250/D350 Series) Signal Destination Status Function Name Control panel Key input matrix circuit CPU PCB data signal 4 MTRKEY4 CN407-13 Control panel Key input matrix circuit CPU PCB data signal 5 MTRKEY5 CN407-14 Control panel Key input matrix circuit...
Page 200 (CN357) (FP-D250/D350 Series) Signal Status Destination Function Name Control panel Key input matrix circuit CPU PCB drive signal 3 DRVK3 CN406-15 Control panel CPU PCB Ground CN406-16 Control panel Key input matrix circuit CPU PCB drive signal 1 DRVK1 CN406-13...
Page 201 Status Function Name Control panel CPU PCB Ground CN406-1 Control panel LED drive signal 0 CPU PCB DRV0 CN406-2 (CN358) (FP-D250/D350 Series) Signal Destination Status Function Name Main CPU PCB EPA mode key input CN205-14 signal — — — 2~3V...
Page 202: Control Panel Pcb B (Fp-D250/D350 Series)
3. Control Panel PCB B (FP-D250/D350 Series) (FP-D250/D350 Series) (CN351) Signal Destination Status Function Name Control panel Key input matrix circuit CPU PCB drive signal 0 DRVK0 CN408-9 Control panel CPU PCB Ground CN408-10 Control panel Key input matrix circuit...
Page 203: Control Panel Pcb C (Fp-D250/D350 Series)
4 Control Panel PCB C (FP-D250/D350 Series) (CN360) (FP-D250/D350 Series) Signal Destination Status Function Name Control panel PCB A MTRLD3 LED matrix signal 3 CN359-11 Control panel Key input matrix circuit PCB A data signal 8 MTRKEY8 CN359-12 Control panel...
Page 204 (CN361) (FP-D250/D350 Series) Signal Destination Status Function Name Control panel PCB D Ground CN362-5 Control panel PCB D DRV3 LED drive signal 3 CN362-6 Control panel PCB D MTRLD1 LED matrix signal 1 CN362-3 Control panel PCB D DRV2 LED drive signal 2...
Page 205: Control Panel Pcb D (Fp-D250/D350 Series)
5 Control Panel PCB D (FP-D250/D350 Series) (FP-D250/D350 Series) (CN362) Signal Destination Status Function Name Control panel PCB C MTRLD2 LED matrix signal 2 CN361-5 Control panel PCB C DRV1 LED drive signal 1 CN361-6 Control panel PCB C MTRLD1...
Page 206: Ccd Pcb (Fp-D250/D350 Series)
4.5 CCD PCB (FP-D250/D350 Series) (FP-D250/D350 Series) (CN801) Signal Destination Status Function Name Main CPU PCB Scanner image data 7 bit Pulse CN209-23 differential output signal SVD7 (MSB) Main CPU PCB Inverse scanner image Pulse CN209-24 data 7 bit differential...
Page 207 Signal Destination Status Function Name Main CPU PCB Inverse Scanner image Pulse CN209-12 data 1 bit differential ISVD1 output signal Main CPU PCB Scanner image data 0 bit Pulse CN209-9 differential output signal SVD0 (LSB) Main CPU PCB Inverse Scanner image Pulse CN209-10 data 0 bit differential...
Page 208 (CN802) (FP-D250/D350 Series) Signal Destination Status Function Name AGND LVPS CN16-6 Ground -12V2 LVPS CN16-5 DC-12V power supply -12V AGND LVPS CN16-4 Ground 12V2 LVPS CN16-3 DC+12V power supply LVPS CN16-2 Ground LVPS CN16-1 DC+5V power supply (FP-D250/D350 Series) (CN803)
Page 209: So Dimm Pcb (Fp-D250/D350 Series)
4.6 SO DIMM PCB (FP-D250/D350 Series) (FP-D250/D350 Series) (CN301) Signal Destination Status Function Name System control Ground CN4-1 System control 3.3V DRAM data bus signal CN4-2 System control 3.3V DRAM data bus signal CN4-3 System control 3.3V DRAM data bus signal...
Page 210 Signal Destination Status Function Name System control 3.3V DRAM address bus signal CN4-14 System control 3.3V DRAM address bus signal CN4-15 System control 3.3V DRAM address bus signal CN4-16 System control 3.3V DRAM address bus signal CN4-17 System control 3.3V DRAM address bus signal CN4-18 System control...
Page 211 Signal Destination Status Function Name System control 3.3V DRAM address bus signal CN4-28 System control 3.3V DRAM address bus signal CN4-29 System control 3.3V +3.3V DC+3.3V power supply CN4-30 System control 3.3V DRAM address bus signal CN4-31 System control 3.3V DRAM address bus signal CN4-32 System control...
Page 212 Signal Destination Status Function Name System control Column address control Pulse signal CAS3 CN4-42 System control Column address control Pulse signal CAS1 CN4-43 System control Pulse RAS0 Row address control signal CN4-44 System control Pulse RAS1 Row address control signal CN4-45 System control —...
Page 213 Signal Destination Status Function Name System control 3.3V DQ24 DRAM data bus signal CN4-56 System control 3.3V DQ25 DRAM data bus signal CN4-57 System control 3.3V DQ26 DRAM data bus signal CN4-58 System control 3.3V DQ28 DRAM data bus signal CN4-59 System control 3.3V...
Page 214 Signal Destination Status Function Name System control — — — CN4-70 System control — — — CN4-71 System control Ground CN4-72 4-93...
Page 215: Flash Dimm Pcb (Fp-D250/D350 Series)
4.7 16 M Flash DIMM PCB (FP-D250/D350 Series) (FP-D250/D350 Series) (CN351) Signal Destination Status Function Name System control Ground CN5-1 System control Flash memory address 3.3V bus signal CN5-2 System control Flash memory address 3.3V bus signal CN5-3 System control Flash memory address 3.3V...
Page 216 Signal Destination Status Function Name System control Flash memory address 3.3V bus signal CN5-14 System control Flash memory address 3.3V bus signal CN5-15 System control Flash memory address 3.3V bus signal CN5-16 System control 3.3V RD/BY Ready / busy check signal CN5-17 System control Write protection control...
Page 217 Signal Destination Status Function Name System control Flash memory address 3.3V bus signal CN5-28 System control Flash memory address 3.3V bus signal CN5-29 System control 3.3V +3.3V DC+3.3V power supply CN5-30 System control — — — CN5-31 System control Flash memory address 3.3V bus signal CN5-32...
Page 218 Signal Destination Status Function Name System control — — — CN5-42 System control — — — CN5-43 System control — — — CN5-44 System control — — — CN5-45 System control — — — CN5-46 System control Flash memory address 3.3V bus signal A16 *...
Page 219 Signal Destination Status Function Name System control Flash memory data bus 3.3V signal DQ12 CN5-56 System control Flash memory data bus 3.3V signal CN5-57 System control Flash memory data bus 3.3V signal DQ11 CN5-58 System control Flash memory data bus 3.3V signal CN5-59...
Page 220 Signal Destination Status Function Name System control Pulse CE * Chip select signal CN5-70 System control Flash memory address 3.3V bus signal CN5-71 System control Ground CN5-72 4-99...
Page 221: Lsu Image Data Control Pcb (Fp-D250/D350Series)
4.8 LSU Image Data Control PCB (FP-D250/D350Series) (CN1) (FP-D250/D350 Series) Signal Destination Status Function Name Main CPU PCB Laser current control ENABLE0 CN38-26 signal Main CPU PCB CAL0 PWM calibration signal CN38-25 Main CPU PCB Laser A APC control ADJ10...
Page 222 Signal Destination Status Function Name Main CPU PCB Pulse LDA5 Laser A image data bit 5 CN38-8 Main CPU PCB Ground CN38-7 Main CPU PCB Pulse LDA6 Laser A image data bit 6 CN38-6 Main CPU PCB Ground CN38-5 Main CPU PCB Pulse LDA7 Laser A image data bit 7...
Page 223 Signal Destination Status Function Name Main CPU PCB Pulse LDB3 Laser B image data bit 3 CN38-40 Main CPU PCB Ground CN38-39 Pulse Main CPU PCB LDB4 Laser B image data bit 4 CN38-38 Main CPU PCB Ground CN38-37 Main CPU PCB Pulse LDB5 Laser B image data bit 5...
Page 224 (Pin photo sensor connector) (FP-D250/D350 Series) Signal Destination Status Function Name Main CPU PCB Ground CN36-4 Pulse Main CPU PCB LSU main scan LSULSYNC CN36-3 synchronization signal Main CPU PCB Ground CN36-2 Main CPU PCB DC+5V power supply CN36-1 (Polygon motor connector)
Page 225: Automatic Duplex Unit (Adu) Driver Pcb (Option) (Fp-D250/D350Series)
4.9 Automatic Duplex Unit (ADU) Driver PCB (Option) (FP-D250/D350Series) (FP-D250/D350 Series) (CN651) Signal Destination Status Function Name Main CPU PCB DC+24Vpower supply CN11-2 Main CPU PCB PGND Power ground CN11-1 Main CPU PCB DC+24Vpower supply CN11-4 Main CPU PCB PGND...
Page 226 (CN652) (FP-D250/D350 Series) Signal Destination Status Function Name Paper detecting sensor Ground CN-3 Paper detecting Detecting sensor DXPESN Paper detecting signal CN-2 Paper detecting sensor DC+5V power supply CN-1 — — — — Paper pass sensor 2 Ground CN-3 Paper pass...
Page 227 (CN653) (FP-D250/D350 Series) Signal Destination Status Function Name Length guide Pulse motor DXLAB Motor drive signal A CN-5 Length guide Pulse motor DXLA Motor drive signal A CN-4 Length guide Pulse motor DXLB Motor drive signal B CN-3 Length guide...
Page 228 (CN654) (FP-D250/D350 Series) Signal Destination Status Function Name Paper feed clutch +12V2 Clutch drive signal CN-2 Paper feed clutch DC+24V power supply CN-1 ADU main Pulse motor DXMA Motor drive signal A CN-1 ADU main motor DC+24V power supply CN-3...
Page 229 (CN655) (FP-D250/D350 Series) Signal Destination Status Function Name Paper length sensor Ground CN-3 Paper length Paper length guide sensor home position detecting PSLSN CN-2 signal Paper length sensor DC+5V power supply CN-1 — — — — Paper width sensor Ground...
Page 230: Low Voltage Power Supply Pcb (Fp-D250/D350Series)
4.10 Low Voltage Power Supply PCB (FP-D250/D350Series) (FP-D250/D350 Series) (CN1/CN2) Signal Destination Status Function Name AC 120V / AC 220 - Power cord 240V power supply AC 120V / AC 220 - Power cord 240V power supply (CN3) (FP-D250/D350 Series)
Page 231 (CN6) (FP-D250/D350 Series) Signal Destination Status Function Name Main motor PGND Power ground CN1-2 Main motor Door SW open : 0V CN1-1 Door SW close : 24V DC+24V power supply Wait / Error : (CN7) (FP-D250/D350 Series) Signal Destination Status...
Page 232 (CN10) (FP-D250/D350 Series) Signal Destination Status Function Name Main CPU PCB DC+12V power supply CN9-1 Main CPU PCB AGND Ground CN9-2 Main CPU PCB Ground CN9-3 Main CPU PCB Ground CN9-4 Main CPU PCB DC+5V power supply CN9-5 Main CPU PCB...
Page 233 (CN12) (FP-D250/D350 Series) Signal Destination Status Function Name PAPERVP CNSQ-1 DC+24V power supply PAPERVP CNSQ-2 DC+24V power supply PGND CNSQ-3 Power ground PGND CNSQ-8 Power ground (CN13) (FP-D250/D350 Series) Signal Destination Status Function Name PAPERVP CNSCN-1 DC+24V power supply PAPERVP...
Page 234 (CN15) (FP-D250/D350 Series) Signal Destination Status Function Name Battery 12BT DC+16V power supply Battery Ground (CN16) (FP-D250/D350 Series) Signal Destination Status Function Name CCD PCB DC+5V power supply CN802-6 CCD PCB Ground CN802-5 CCD PCB DC+12V power supply CN802-4 CCD PCB...
Page 235 (CN18) (FP-D250/D350 Series) Signal Destination Status Function Name HDD1/2 12V1 DC+12V power supply CNPHD1-1 HDD1/2 Ground CNPHD1-2 HDD1/2 Ground CNPHD1-3 HDD1/2 DC+5V power supply CNPHD1-4 (CN19) (FP-D250/D350 Series) Signal Destination Status Function Name HDD3/Zip 12V1 DC+12V power supply CNPHD1-1 HDD3/Zip...
Page 236 (CN20) (FP-D250/D350 Series) Signal Destination Status Function Name System control 3.3V 3.3V DC+3.3V power supply CN14-1 System control Ground CN14-2 System control Ground CN14-3 System control 5.1V DC+5.1V power supply CN14-4 System control Ground CN14-5 System control 12V1 DC+12V power supply...
Page 237 (CN22) (FP-D250/D350 Series) Signal Destination Status Function Name Printer control 3.3V 3.3V DC+3.3V power supply PCB S1-1 Printer control Ground PCB S1-2 Printer control Ground PCB S1-3 Printer control 5.1V DC+5.1V power supply PCB S1-4 (CN23) Not used 4-116...
Page 238: High Voltage Power Supply Pcb (Fp-D250/D350 Series)
4.11 High Voltage Power supply PCB (FP-D250/D350 Series) (CNHV) (FP-D250/D350 Series) Signal Destination Status Function Name Main CPU PCB DC+24V power supply CN10-12 Main CPU PCB PGND Power ground CN10-11 Main CPU PCB Separation high voltage HVDCNT CN10-10 ON / OFF signal...
Page 239: Ac Drive Pcb (Fp-D250/D350 Series)
4.12 AC Drive PCB (FP-D250/D350 Series) (CN201) (FP-D250/D350 Series) Signal Destination Status Function Name AC 120V / AC 220 - Power switch 240V power supply (CN203) (FP-D250/D350 Series) Signal Destination Status Function Name Fuser AC 120V / AC 220 -...
Page 240 (CN206) (FP-D250/D350 Series) Signal Destination Status Function Name Main CPU PCB DC+5V power supply CN5-11 Main CPU PCB Fuser lamp ON / OFF HTTR1 CN5-9 signal Main CPU PCB — – — CN5-10 4-119...
Page 241: Printer Controller Pcb (Option) (Fp-D250/D350 Series)
4.13 Printer Controller PCB (Option) (FP-D250/D350 Series) (FP-D250/D350 Series) (CNS1) Signal Status Destination Function Name 3.3V 3.3V LVPS CN22-1 DC+3.3V power supply LVPS CN22-2 Ground LVPS CN22-3 Ground LVPS CN22-4 DC+5V power supply (CNJ1) (FP-D250/D350 Series) Signal Destination Function Status...
Page 242 Signal Status Destination Function Name 3.3V SDRAM DIMM-13 Data 9 3.3V DQ10 SDRAM DIMM-14 Data 10 3.3V DQ11 SDRAM DIMM-15 Data 11 3.3V DQ12 SDRAM DIMM-16 Data 12 3.3V DQ13 SDRAM DIMM-17 Data 13 3.3V +3.3V SDRAM DIMM-18 DC+3.3V power supply 3.3V DQ14 SDRAM DIMM-19...
Page 243 Signal Destination Status Function Name 3.3V SDRAM DIMM-33 Address 0 3.3V SDRAM DIMM-34 Address 2 3.3V SDRAM DIMM-35 Address 4 3.3V SDRAM DIMM-36 Address 6 3.3V SDRAM DIMM-37 Address 8 3.3V SDRAM DIMM-38 Address 10 — SDRAM DIMM-39 — — 3.3V +3.3V SDRAM DIMM-40...
Page 244 Signal Status Destination Function Name — SDRAM DIMM-53 — — SDRAM DIMM-54 Ground 3.3V DQ16 SDRAM DIMM-55 Data 16 3.3V DQ17 SDRAM DIMM-56 Data 17 3.3V DQ18 SDRAM DIMM-57 Data 18 3.3V DQ19 SDRAM DIMM-58 Data 19 3.3V +3.3V SDRAM DIMM-59 DC+3.3V power supply 3.3V DQ20...
Page 245 Signal Destination Status Function Name 3.3V +3.3V SDRAM DIMM-73 DC+3.3V power supply 3.3V DQ28 SDRAM DIMM-74 Data 28 3.3V DQ29 SDRAM DIMM-75 Data 29 3.3V DQ30 SDRAM DIMM-76 Data 30 3.3V DQ31 SDRAM DIMM-77 Data 31 SDRAM DIMM-78 Ground CLK2 SDRAM DIMM-79 Clock 2 —...
Page 246 Signal Status Destination Function Name 3.3V DQ38 SDRAM DIMM-93 Data 37 3.3V DQ39 SDRAM DIMM-94 Data 38 3.3V DQ40 SDRAM DIMM-95 Data 39 SDRAM DIMM-96 Data 40 3.3V DQ41 SDRAM DIMM-97 Ground 3.3V DQ42 SDRAM DIMM-98 Data 41 3.3V DQ43 SDRAM DIMM-99 Data 42 SDRAM DIMM-...
Page 247 Signal Destination Status Function Name SDRAM DQM5 Data input/output mask 5 DIMM-113 SDRAM — — — DIMM-114 SDRAM -RAS Low address strove DIMM-115 SDRAM Ground DIMM-116 SDRAM 3.3V Address 1 DIMM-117 SDRAM 3.3V Address 3 DIMM-118 SDRAM 3.3V Address 5 DIMM-119 SDRAM 3.3V...
Page 248 Signal Status Destination Function Name SDRAM 3.3V +3.3V DC+3.3V power supply DIMM-133 SDRAM — — — DIMM-134 SDRAM — — — DIMM-135 SDRAM — — — DIMM-136 SDRAM — — — DIMM-137 SDRAM Ground DIMM-138 SDRAM 3.3V DQ48 Data 48 DIMM-139 SDRAM 3.3V...
Page 249 Signal Destination Status Function Name SDRAM 3.3V DQ56 Data 56 DIMM-153 SDRAM 3.3V DQ57 Data 57 DIMM-154 SDRAM 3.3V DQ58 Data 58 DIMM-155 SDRAM 3.3V Data 59 DQ59 DIMM-156 SDRAM 3.3V +3.3V DC+3.3V power supply DIMM-157 SDRAM 3.3V DQ60 Data 60 DIMM-158 SDRAM 3.3V...
Page 250 (CNJ2) (FP-D250/D350 Series) Signal Status Destination Function Name Network Card DC+5V power supply CNJ10-31 Network Card DC+5V power supply CNJ10-32 Network Card DC+5V power supply CNJ10-33 Network Card /CSP2 Card select signal 2 CNJ10-34 Network Card Data 15 CNJ10-35 Network Card...
Page 251 Signal Destination Status Function Name Network Card Address 0 CNJ10-51 Network Card Data 7 CNJ10-52 Network Card Data 6 CNJ10-53 Network Card Address 15 CNJ10-54 Network Card Data 5 CNJ10-55 Network Card Address 14 CNJ10-56 Network Card Data 4 CNJ10-57 Network Card Address 13 CNJ10-58...
Page 252 Signal Status Destination Function Name Network Card /WAIT Wait signal CNJ10-11 Network Card Address 6 CNJ10-12 Network Card /CSP1 Card select signal 1 CNJ10-13 Network Card Address 5 CNJ10-14 Network Card — — — CNJ10-15 Network Card — — — CNJ10-16 Read Network Card...
Page 253 (CNJ4) (FP-D250/D350 Series) Signal Status Destination Function Name PC printer port Centronics /STB Strove signal connector 1 PC printer port Centronics DATA1 Data 1 connector 2 PC printer port Centronics DATA2 Data 2 connector 3 PC printer port Centronics DATA3...
Page 254 Signal Status Destination Function Name PC printer port Centronics — — — connector 15 PC printer port Centronics — — — connector 16 PC printer port Centronics Frame ground connector 17 PC printer port Printer connection Centronics detecting signal connector 18 PC printer port Centronics Ground...
Page 255 PC printer port Centronics — — — connector 35 Bi-directional PC printer port Centronics communication detect SELIN signal connector 36 (CNJ5) (FP-D250/D350 Series) Signal Destination Status Function Name Main CPU PCB Ground CN203-1 Main CPU PCB Ground CN203-2 Main CPU PCB Ground...
Page 256 Signal Status Destination Function Name Main CPU PCB Ground CN203-7 Main CPU PCB Ground CN203-8 Main CPU PCB Ground CN203-9 Main CPU PCB Ground CN203-10 Main CPU PCB Ground CN203-11 Main CPU PCB Ground CN203-12 Main CPU PCB Ground CN203-13 Main CPU PCB Ground CN203-14...
Page 257 Signal Destination Status Function Name Main CPU PCB Ground CN203-27 Main CPU PCB Ground CN203-28 Main CPU PCB Ground CN203-29 Main CPU PCB Ground CN203-30 Main CPU PCB Image data receive /IDRDY CN203-31 ready signal Main CPU PCB /IDSTB Image data strove signal CN203-32 Main CPU PCB Ground...
Page 258 (CNJ8) (FP-D250/D350 Series) Signal Status Destination Function Name Printer Hard disk IDE bus /RESET Reset signal connector 1 Printer Hard disk IDE bus Ground connector 2 Printer Hard disk IDE bus DATA7 Data 7 connector 3 Printer Hard disk IDE bus...
Page 259 Signal Status Destination Function Name Printer Hard disk IDE bus DATA1 Data 1 connector 15 Printer Hard disk IDE bus DATA14 Data 14 connector 16 Printer Hard disk IDE bus DATA0 Data 0 connector 17 Printer Hard disk IDE bus DATA15 Data 15 connector 18...
Page 260 Signal Destination Status Function Name Printer Hard DMA transfer accept disk IDE bus /DACK signal connector 29 Printer Hard disk IDE bus Ground connector 30 Printer Hard Interrupt signal disk IDE bus connector 31 Printer Hard 16 bit I/O select signal /IOCS16 disk IDE bus connector 32...
Page 261: Network Card (Option) (Fp-D250/D350 Series)
4.14 Network Card (Option) (FP-D250/D350 Series) (CNJ2A) (FP-D250/D350 Series) Signal Destination Status Function Name 585mV~3.1V Ethernet cable -1 Transmit data + 585mV~3.1V Ethernet cable -2 Transmit data - 585mV~3.1V Ethernet cable -3 Receive data + — Ethernet cable -4 —...
Page 262 Signal Status Destination Function Name Rizer card — — — CN601-A9 Rizer card DC+5V power supply CN601-A10 Rizer card — — — CN601-A11 Rizer card Ground CN601-A12 Rizer card Ground CN601-A13 Rizer card — — — CN601-A14 Rizer card RST# Reset CN601-A15 Rizer card...
Page 263 Signal Destination Status Function Name Rizer card AD_20 Address/data 20 CN601-A29 Rizer card Ground CN601-A30 Rizer card AD_18 Address/data 18 CN601-A31 Rizer card AD_16 Address/data 16 CN601-A32 Rizer card — — — CN601-A33 Rizer card FRAME# Cycle frame CN601-A34 Rizer card Ground CN601-A35 Rizer card...
Page 264 Signal Status Destination Function Name Rizer card Add in board detect RSNT#1 CN601-B9 signal 1 Rizer card — — — CN601-B10 Rizer card Add in board detect PRSNT#2 CN601-B11 signal 2 Rizer card Ground CN601-B12 Rizer card Ground CN601-B13 Rizer card —...
Page 265 Signal Destination Status Function Name Rizer card AD_21 Address /data 21 CN601-B29 Rizer card AD_19 Address/data 19 CN601-B30 Rizer card — — — CN601-B31 Rizer card AD_17 Address/data 17 CN601-B32 Bus command/byte Rizer card CBE#2 enable 2 CN601-B33 Rizer card Ground CN601-B34 Rizer card...
Page 266 (CNJ10) (FP-D250/D350 Series) Signal Status Status Destination Function Name Printer controller Data 2 PCB CNJ2-31 Printer controller Address 11 PCB CNJ2-32 Printer controller Data 1 PCB CNJ2-33 Printer controller Address 10 PCB CNJ2-34 Printer controller Data 0 PCB CNJ2-35 Printer controller...
Page 267 Signal Destination Status Function Name Printer controller — — — PCB CNJ2-51 Printer controller Ground PCB CNJ2-52 Printer controller — — — PCB CNJ2-53 Printer controller — — — PCB CNJ2-54 Printer controller /INTPRT2 Interrupt signal 2 PCB CNJ2-55 Printer controller Ground PCB CNJ2-56 Printer controller...
Page 268 Signal Status Destination Function Name Printer controller Data 10 PCB CNJ2-11 Printer controller Ground PCB CNJ2-12 Printer controller Data 9 PCB CNJ2-13 Printer controller Data 8 PCB CNJ2-14 Printer controller /INTPRT1 Inerrupt signal 1 PCB CNJ2-15 Printer controller Ground PCB CNJ2-16 Printer controller Address 3 PCB CNJ2-17...
Page 269: Hard Disk Drive For Filing/Back-Up (Fp-D250/D350 Series)
4.15 Hard Disk Drive for Filing/Back-up (FP-D250/D350 Series) (FP-D250/D350 Series) (CNSHD1/2) Signal Destination Status Function Name System control Reset RESET Reset signal CN6-1 System control Ground CN6-2 HOST System control DATA 7 Hard disk data bus CN6-3 HOST System control...
Page 270 Signal Destination Status Function Name HOST System control DATA 13 Hard disk data bus CN6-14 HOST System control DATA 1 Hard disk data bus CN6-15 HOST System control DATA 14 Hard disk data bus CN6-16 HOST System control DATA 0 Hard disk data bus CN6-17 HOST...
Page 271 Signal Destination Status Function Name System control — — — CN6-28 System control — — — CN6-29 System control Ground CN6-30 HOST System control Hard disk interrupt Pulse IRQ14 signal (15) CN6-31 HOST System control Hard disk 16 bit transfer IO16 control signal CN6-32...
Page 272 (CNPHD1/2) (FP-D250/D350 Series) Signal Status Function Destination Name LVPS 12V1 DC+12V power supply CN18-1 LVPS Ground CN18-2 LVPS Ground CN18-3 LVPS DC+5V power supply CN18-4 4-151...
Page 273: Zip Drive (Fp-D250/D350 Series)
4.16 Zip Drive (FP-D250/D350 Series) (FP-D250/D350 Series) (CNSRMD) Signal Destination Status Function Name System control Reset RESET Reset signal CN6-1 System control Ground CN6-2 HOST System control DATA 7 Hard disk data bus CN6-3 HOST System control DATA 8 Hard disk data bus...
Page 274 Signal Destination Status Function Name HOST System control DATA 13 Hard disk data bus CN6-14 HOST System control DATA 1 Hard disk data bus CN6-15 HOST System control DATA 14 Hard disk data bus CN6-16 HOST System control DATA 0 Hard disk data bus CN6-17 HOST...
Page 275 Signal Destination Status Function Name System control — — — CN6-28 System control — — — CN6-29 System control Ground CN6-30 HOST System control Hard disk interrupt Pulse IRQ14 signal (15) CN6-31 HOST System control Hard disk 16 bit transfer IO16 control signal CN6-32...
Page 276 (CNPRMD) (FP-D250/D350 Series) Signal Status Function Destination Name — — — — LVPS Ground CN19-2 LVPS Ground CN19-3 LVPS DC+5V power supply CN19-4 4-155...
Page 277: Main Cpu Pcb (Fp-D450/D600 Series)
4.17 Main CPU PCB (FP-D450/D600 Series) (FP-D450/D600 Series) (CN1) Signal Destination Status Function Name LVPS PCB Scanner 24V ON/OFF SVCNT CN17-7 signal LVPS PCB Printer 24 V ON/OFF PVCNT CN17-6 signal LVPS PCB Pulse ZCRS Zero cross Signal CN17-5 4-156...
Page 278 (CN2) (FP-D450/D600 Series) Signal Destination Status Function Name Bypass paper size sensor 3 DC+5Vpower supply CN-1 Bypass paper Paper size detecting Detect size sensor 3 signal 3 HSSN3 CN-2 Bypass paper size sensor 3 Ground CN-3 Bypass paper size sensor 2 DC+5Vpower supply CN-1 Bypass paper...
Page 279 (CN3) (FP-D450/D600 Series) Signal Destination Status Function Name Copy density Ground sensor CN-1 Copy density Analog Paper base tone CDSN2 sensor CN-2 0–5V detecting signal Copy density VCDS Sensor ON/OFF signal sensor CN-3 Copy density Analog Copy density detecting CDSN1 sensor CN-4 0–5V signal...
Page 280 (CN4) (FP-D450/D600 Series) Signal Destination Status Function Name Image processing Printer condition change PCB CN212-1 detection signal Image processing PRDY Printer ready signal PCB CN212-2 Image processing VRDY VSYNC receive signal PCB CN212-3 Image processing Paper feed completion PACK PCB CN212-4 signal Image processing Scanner sub-scan...
Page 281 Signal Destination Status Function Name Pulse Image processing Scanner horizontal SLSYNC PCB CN212-17 synchronization signal Image processing Shading compensation PCB CN212-18 standard data SHRDY completion signal Image processing SREQ Scanner request PCB CN212-19 Image processing Pulse ZCSP Host zero cross signal PCB CN212-20 Image processing Pulse...
Page 282 (CN5) (FP-D450/D600 Series) Signal Status Function Destination Name Main motor PGND Power ground CN-1 Main motor Main motor drive control MMCNT CN-2 signal Stop Rotate Main motor lock Main motor MMLCK CN-3 detecting signal Main motor Pulse MMCLK Main motor clock signal CN-4 Discharge lamp Discharge lamp ON/...
Page 283 (CN6) (FP-D450/D600 Series) Signal Destination Status Function Name Developer Developer cooling fan cooling fan motor ON/OFF signal OZFM motor CN-1 Dust collection Dust collection fan fan motor CN-1 motor ON/OFF siganl DDFM Developer Developer cooling fan Stop Rotate cooling fan motor lock detecting OZFL motorCN-2...
Page 284 (CN7) (FP-D450/D600 Series) Signal Destination Status Function Name System console 32 bit data transfer PCB CNSQ-23 output signal Pulse F32BOUT or LCC driver PCB CN562-5 System console 32 bit data transfer PCB CNSQ-27 enable signal FENB or LCC driver PCB CN562-6 System console 32 bit data transfer latch PCB CNSQ-25...
Page 285 (CN8) (FP-D450/D600 Series) Signal Destination Status Function Name Inverting shift Pulse tray PCB F32AOUT 32 bit data output signal CN601-5 Inverting shift 32 bit data transfer data tray PCB enable signal FENB CN601-6 Inverting shift 32 bit data transfer latch Pulse tray PCB signal...
Page 286 (CN9) (FP-D450/D600 Series) Signal Destination Status Function Name LVPS PGND Power ground CN11-1 LVPS PGND Power ground CN11-2 LVPS DC +24V power supply CN11-5 LVPS DC +24V power supply CN11-6 LVPS PMVP DC +24V power supply CN11-8 LVPS DC +12V power supply CN10-1 LVPS AGND...
Page 287 (CN10) (FP-D450/D600 Series) Signal Destination Status Function Name Leak HVPS Charge high voltage HVLKC CN701-12 leak detecting signal HVPS Charge high voltage HVCNT CN701-11 ON/OFF signal HVPS Grid bias adjustment Analog GREF CN701-10 0–8.5V signal HVPS HVBCNT Bias ON/OFF signal CN701-9 HVPS Analog...
Page 288 (CN11) (FP-D450/D600 Series) Signal Destination Status Function Name ADU driver PCB PGND Power ground CN651-2 ADU driver PCB DC+24V power supply CN651-1 ADU driver PCB PGND Power ground CN651-4 ADU driver PCB DC+24V power supply CN651-3 ADU driver PCB Pulse F32AOUT 32 bit data output signal CN651-5...
Page 289 Signal Destination Status Function Name ADU tray sensor Ground CN-3 ADU driver PCB Detecting ADUSL ADU detecting signal CN2-24 — — — — ADU driver PCB Ground CN2-22 (CN12) (FP-D450/D600 Series) Signal Destination Status Function Name Exhaust fan 1 PGND Power ground CN-3 Exhaust fan 1...
Page 290 Signal Destination Status Function Name Pulse Toner bottle Toner bottle motor drive BMBB motor CN-1 signal B Toner bottle DC+24V power supply motor CN-2 Pulse Toner bottle motor drive Toner bottle motor CN-3 signal B Pulse Toner bottle Toner bottle motor drive BMAB motor CN-4 signal A...
Page 291 (CN13) (FP-D450/D600 Series) Signal Destination Status Function Name Platen cover open / close Ground sensor CN-3 Platen cover Platen cover open / Close Open open / close close detecting signal PCSN sensor CN-2 Platen cover open / close DC+5V power supply sensor CN-1 Platen cover angle sensor...
Page 292 (CN15) (FP-D450/D600 Series) Signal Destination Status Function Name Finisher Inverse sorter receive Pulse ISTRX connector CN-8 signal Finisher Pulse STRX Sorter receive signal connector CN-9 Finisher Ground connector CN-10 Finisher Inverse sorter transfer Pulse ISTTX connector CN-11 signal Finisher Pulse STTX Sorter transfer signal connector CN-12...
Page 293 (CN17) (FP-D450/D600 Series) Signal Destination Status Function Name Optics fan 1 PGND Power ground CN-3 Optics fan 1 Stop Rotate Optics fan motor 1 lock LPFL1 CN-2 detecting signal Optics fan 1 Optics fan motor 1 ON / LPFM1 CN-1 OFF signal Exposure lamp inverter PCB...
Page 294 (CN18) (FP-D450/D600 Series) Signal Destination Status Function Name — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 295 Signal Destination Status Function Name Exhaust fan relay harness —PGND Power ground CNEXF-3 Exhaust fan Exhaust fan motor 5 Stop Rotate relay harness lock detecting signal EXFL5 CNEXF-2 Exhaust fan Exhaust fan motor 5 relay harness ON/OFF signal EXFM5 CNEXF-1 4-174...
Page 296 (CN20) (FP-D450/D600 Series) Signal Destination Status Function Name Original size sensor 1 DC+5V power supply CN-1 Original size Original size detecting sensor 1 AOSS1 sensor signal 1 CN-2 Original size Original size detecting sensor 1 AOS1 sensor optics signal 1 CN-3 Original size sensor 1...
Page 297 Signal Destination Status Function Name Original size Original size detecting sensor 4 sensor optics signal 4 AOS4 CN-3 Original size sensor 4 Ground CN-4 Original size sensor 5 DC+5V power supply CN-1 Original size Original size detecting sensor 5 sensor signal 5 AOSS5 CN-2 Original size...
Page 298 (CN22) (FP-D450/D600 Series) Signal Destination Status Function Name — — — — — — — — — — — — — — — — — — — — Paper pass sensor (Upper stage) DC+5V power supply CN-1 — — — —...
Page 299 Signal Destination Status Function Name — — — — — — — — — — — — — — — — — — — — (CN23) (FP-D450/D600 Series) Signal Destination Status Function Name Paper feed clutch —PVP DC+24V power supply (Lower stage) CN-1 Paper feed...
Page 300 Signal Destination Status Function Name Paper pass sensor DC+5V power supply (Lower stage) CN-1 Paper level Paper level detecting sensor signal PEWSN2 (Lower stage) CN-2 Paper pass Detecting sensor CRRSN2 Paper detecting signal (Lower stage) CN-2 Paper level sensor Ground (Lower stage) CN-3 Paper pass...
Page 301 (CN26) (FP-D450/D600 Series) Signal Destination Status Function Name Lift motor Motor rotation control (Upper stage) signal (Upper direction) LUM1-1 CN-1 Lift motor Motor rotation control (Upper stage) signal (Lower direction) LUM1-2 CN-2 (CN27) (FP-D450/D600 Series) Signal Destination Status Function Name Lift motor Motor rotation control (Lower stage)
Page 302 (CN29) (FP-D450/D600 Series) Signal Destination Status Function Name Bypass paper feed clutch DC+24V power supply CN-1 Bypass paper Bypass paper feed feed clutch clutch ON / OFF signal HFCR CN-2 Registration roller clutch DC+24V power supply CN-1 Registration Registration roller clutch roller clutch ON / OFF signal RRCR...
Page 303 Signal Destination Status Function Name Registration roller paper DC+5V power supply pass sensor CN-1 — — — — Registration Registration roller paper roller paper pass sensor detecting Detecting RRSN pass sensor signal CN-2 — — — — Registration roller paper Ground pass sensor CN-3...
Page 304 (CN31) (FP-D450/D600 Series) Signal Destination Status Function Name Pulse Optics motor Optics motor drive LMBB CN-11 signal B Optics motor DC+24V power supply CN-9 Pulse Optics motor Optics motor drive CN-7 signal B Pulse Optics motor Optics motor drive LMAB CN-5 signal A Optics motor...
Page 305 (CN34) (FP-D450/D600 Series) Signal Destination Status Function Name Image processing Sub-scan direction GVSYNC PCB CN202-1 synchronization signal Image processing Gate array chip select GIPGCS PCB CN202-2 signal Image processing Pulse GIWR Gate array write signal PCB CN202-3 Image processing GIRD Gate array read signal PCB CN202-4 Image processing...
Page 306 Signal Destination Status Function Name Image processing Pulse GAD1 Data bus PCB CN202-20 Image processing Pulse GAD2 Data bus PCB CN202-21 Image processing Pulse GAD3 Data bus PCB CN202-22 Image processing Pulse GAD4 Data bus PCB CN202-23 Image processing Pulse GAD5 Data bus PCB CN202-24...
Page 307 (FP-D450/D600 Series) (CN35) Signal Destination Status Function Name Pulse Image processing CPU enable signal PCB CN213-1 Image processing BRIW Read/write select signal PCB CN213-2 Pulse IPC circuit chip select Image processing MB38CS signal PCB CN213-3 IPC communication Image processing IPRXD receive signal PCB CN213-4 IPC communication...
Page 308: System Control Pcb (Fp-D450/D600 Series)
4.18 System Control PCB (FP-D450/D600 Series) (CN1 - CN2) Not used (FP-D450/D600 Series) (CN3) Signal Destination Status Function Name Main CPU PCB COM2 data terminal ready DTR2J CN201-1 signal Main CPU PCB +12V DC+12V power supply CN201-2 Main CPU PCB RTS2J COM2 request signal CN201-3...
Page 309 Signal Destination Status Function Name Riser card PCB GNT0 Grant signal CN601-17 Main CPU PCB Ground CN201-18 — — — — Main CPU PCB AD30 PCI bus address data signal CN201-20 3.3V Main CPU PCB +3.3V DC+3.3V power supply CN201-21 Main CPU PCB AD28 PCI bus address data signal...
Page 310 Signal Destination Status Function Name Main CPU PCB Ground CN201-37 Pulse Main CPU PCB STOP Stop signal CN201-38 3.3V Main CPU PCB +3.3V DC+3.3V power supply CN201-39 Pulse Main CPU PCB SDONE Snoop done signal CN201-40 Pulse Main CPU PCB Snoop back off signal CN201-41 Main CPU PCB...
Page 311 Signal Destination Status Function Name Main CPU PCB PCI bus address data signal AD02 CN201-57 Main CPU PCB AD00 PCI bus address data signal CN201-58 Main CPU PCB DC+5V power supply CN201-59 — — — — Main CPU PCB DC+5V power supply CN201-61 Main CPU PCB DC+5V power supply...
Page 312 Signal Destination Status Function Name Main CPU PCB Ground CN201-115 Main CPU PCB Pulse CLKB PCI bus clock B CN201-116 Main CPU PCB Ground CN201-117 Pulse Riser card PCB REQ0 DMA transfer request signal CN601-118 Main CPU PCB DC+5V power supply CN201-119 Main CPU PCB AD31...
Page 313 Signal Destination Status Function Name Pulse Main CPU PCB IRDY Initiator ready signal CN201-135 Main CPU PCB 3.3V +3.3V DC+3.3V power supply CN201-136 Pulse Main CPU PCB DEVSEL Device select signal CN201-137 Main CPU PCB Ground CN201-138 Pulse Main CPU PCB LOCK Lock signal CN201-139...
Page 314 Signal Destination Status Function Name Main CPU PCB AD05 PCI bus address data signal CN201-155 Main CPU PCB AD03 PCI bus address data signal CN201-156 Main CPU PCB Ground CN201-157 Main CPU PCB AD01 PCI bus address data signal CN201-158 Main CPU PCB DC+5V power supply CN201-159...
Page 315 (CN4) (FP-D450/D600 Series) Signal Destination Status Function Name SO DIMM PCB Ground CN301-1 SO DIMM PCB 3.3V DRAM data bus signal CN301-2 SO DIMM PCB 3.3V DRAM data bus signal CN301-3 SO DIMM PCB 3.3V DRAM data bus signal CN301-4 SO DIMM PCB 3.3V DRAM data bus signal...
Page 316 Signal Destination Status Name SO DIMM PCB 3.3V DRAM data bus signal CN301-21 SO DIMM PCB 3.3V DRAM data bus signal CN301-22 SO DIMM PCB 3.3V DQ10 DRAM data bus signal CN301-23 SO DIMM PCB 3.3V DQ11 DRAM data bus signal CN301-24 SO DIMM PCB 3.3V...
Page 317 Signal Destination Status Function Name Pulse SO DIMM PCB Column address control CAS2 CN301-41 signal Pulse SO DIMM PCB Column address control CAS3 CN301-42 signal Pulse SO DIMM PCB Column address control CAS1 CN301-43 signal SO DIMM PCB RAS0 Row address control signal CN301-44 Pulse SO DIMM PCB...
Page 318 Signal Destination Status Function Name SO DIMM PCB 3.3V +3.3V DC+3.3V power supply CN301-61 SO DIMM PCB 3.3V DQ29 DRAM data bus signal CN301-62 SO DIMM PCB 3.3V DQ30 DRAM data bus signal CN301-63 SO DIMM PCB 3.3V DQ31 DRAM data bus signal CN301-64 SO DIMM PCB —...
Page 319 (CN5) (FP-D450/D600 Series) Signal Destination Status Function Name 16 M Flash DIMM PCB Ground CN351-1 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-2 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-3 16 M Flash Flash memory address 3.3V DIMM PCB...
Page 320 Signal Destination Status Function Name 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-15 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-16 16 M Flash Pulse DIMM PCB RD/BY Ready / busy check signal CN351-17 16 M Flash Write protection control...
Page 321 Signal Destination Status Function Name 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-29 16 M Flash 3.3V DIMM PCB +3.3V DC+3.3V power supply CN351-30 16 M Flash DIMM PCB — — — CN351-31 16 M Flash Flash memory address 3.3V DIMM PCB...
Page 322 Signal Destination Status Function Name 16 M Flash DIMM PCB — — — CN351-43 16 M Flash DIMM PCB — — — CN351-44 16 M Flash DIMM PCB — — — CN351-45 16 M Flash DIMM PCB — — — CN351-46 16 M Flash Flash memory address...
Page 323 Signal Destination Status Function Name 16 M Flash Flash memory data bus 3.3V DIMM PCB signal CN351-57 16 M Flash Flash memory data bus 3.3V DIMM PCB signal DQ11 CN351-58 16 M Flash Flash memory data bus 3.3V DIMM PCB signal CN351-59 16 M Flash...
Page 324 Signal Destination Status Function Name 16 M Flash Flash memory address 3.3V DIMM PCB bus signal CN351-71 16 M Flash DIMM PCB Ground CN351-72 4-203...
Page 325 (CN14) (FP-D450/D600 Series) Signal Destination Status Function Name 3.3V 3.3V LVPS CN20-1 DC+3.3V power supply LVPS CN20-2 Ground LVPS CN20-3 Ground 5.1V LVPS CN20-4 DC+5.1V power supply LVPS CN20-5 Ground 12V1 LVPS CN20-6 DC+12V power supply LVPS CN20-7 Ground –12V1 LVPS CN20-8 DC-12V power supply -12V...
Page 326: Control Panel Pcb (Fp-D450/D600 Series)
4.19 Control Panel PCB (FP-D450/D600 Series) 1. Control Panel CPU PCB (FP-D450/D600 Series) (FP-D450/D600 Series) (CN401) Signal Destination Status Function Name Image processing DC+5V power supply PCB CN205-13 Image processing DC+5V power supply PCB CN205-14 Image processing Ground PCB CN205-11 Image processing Ground PCB CN205-12...
Page 327 (CN402) (FP-D450/D600 Series) Signal Destination Status Function Name Touch panel An abscissa detecting Select PCB CN-1 signal 1 Analog touch Touch panel An ordinate detecting PCB CN-2 signal 2 Analog touch Touch panel An abscissa detecting PCB CN-3 signal 2 Touch panel An ordinate detecting Select...
Page 328 (CN404) (FP-D450/D600 Series) Signal Destination Status Function Name LCD backlight INV1 Ground CN-1 LCD backlight AC voltage Approx. 1kVP-P INV2 CN-2 4-207...
Page 329 (CN406) (FP-D450/D600 Series) Signal Status Destination Function Name Control panel PCB A Ground CN357-15 Control panel PCB A DRV0 LED drive signal 0 CN357-16 Control panel PCB A DRV1 LED drive signal 1 CN357-13 Control panel PCB A DRV2 LED drive signal 2 CN357-14 Control panel PCB A...
Page 330 (CN407) (FP-D450/D600 Series) Signal Destination Status Function Name Control panel Key input matrix circuit PCB A data signal 15 MTRKEY15 CN356-13 Control panel Key input matrix circuit PCB A data signal 14 MTRKEY14 CN356-14 Control panel Key input matrix circuit PCB A data signal 13 MTRKEY13...
Page 331 (CN408) (FP-D450/D600 Series) Signal Destination Status Function Name Control panel PCB B Ground CN351-9 Control panel Key input matrix circuit PCB B data signal 6 MTRKEY6 CN351-10 Control panel Key input matrix circuit PCB B data signal 7 MTRKEY7 CN351-7 Control panel Key input matrix circuit PCB B...
Page 332: Control Panel Pcb A (Fp-D450/D600 Series)
2. Control Panel PCB A (FP-D450/D600 Series) (CN354 - CN355) Not used 4-211...
Page 333 (CN356) (FP-D450/D600 Series) Signal Destination Status Function Name Control panel Key input matrix circuit CPU PCB data signal 4 MTRKEY4 CN407-13 Control panel Key input matrix circuit CPU PCB data signal 5 MTRKEY5 CN407-14 Control panel Key input matrix circuit CPU PCB data signal 2 MTRKEY2...
Page 334 (CN357) (FP-D450/D600 Series) Signal Status Destination Function Name Control panel Key input matrix circuit CPU PCB drive signal 3 DRVK3 CN406-15 Control panel CPU PCB Ground CN406-16 Control panel Key input matrix circuit CPU PCB drive signal 1 DRVK1 CN406-13 Control panel Key input matrix circuit CPU PCB...
Page 335 Signal Destination Status Function Name Control panel CPU PCB Ground CN406-1 Control panel LED drive signal 0 CPU PCB DRV0 CN406-2 (FP-D450/D600 Series) (CN358) Signal Destination Status Function Name Image processing EPA mode key input PCB CN205-16 signal — — —...
Page 336: Control Panel Pcb B (Fp-D450/D600 Series)
3. Control Panel PCB B (FP-D450/D600 Series) (FP-D450/D600 Series) (CN351) Signal Destination Status Function Name Control panel Key input matrix circuit CPU PCB drive signal 0 DRVK0 CN408-9 Control panel CPU PCB Ground CN408-10 Control panel Key input matrix circuit CPU PCB drive signal 2 DRVK2...
Page 337: Control Panel Pcb C (Fp-D450/D600 Series)
4 Control Panel PCB C (FP-D450/D600 Series) (FP-D450/D600 Series) (CN360) Signal Destination Status Function Name Control panel PCB A MTRLD3 LED matrix signal 3 CN359-11 Control panel Key input matrix circuit PCB A data signal 8 MTRKEY8 CN359-12 Control panel PCB A MTRLD1 LED matrix signal 1...
Page 338 (CN361) (FP-D450/D600 Series) Signal Destination Status Function Name Control panel PCB D Ground CN362-5 Control panel PCB D DRV3 LED drive signal 3 CN362-6 Control panel PCB D MTRLD1 LED matrix signal 1 CN362-3 Control panel PCB D DRV2 LED drive signal 2 CN362-4 Control panel PCB D...
Page 339: Control Panel Pcb D (Fp-D450/D600 Series)
5 Control Panel PCB D (FP-D450/D600 Series) (FP-D450/D600 Series) (CN362) Signal Destination Status Function Name Control panel PCB C MTRLD2 LED matrix signal 2 CN361-5 Control panel PCB C DRV1 LED drive signal 1 CN361-6 Control panel PCB C MTRLD1 LED matrix signal 1 CN361-3 Control panel...
Page 340: Ccd Pcb (Fp-D450/D600 Series)
4.20 CCD PCB (FP-D450/D600 Series) (FP-D450/D600 Series) (CN801) Signal Destination Status Function Name Image Scanner image data 7 bit Pulse processing PCB differential output signal SVD7 CN209-23 (MSB) Image Inverse scanner image Pulse processing PCB data 7 bit differential ISVD7 CN209-24 output signal (MSB) Image...
Page 341 Signal Destination Status Function Name Image Inverse Scanner image Pulse processing PCB data 1 bit differential ISVD1 CN209-12 output signal Image Scanner image data 0 bit Pulse processing PCB differential output signal SVD0 CN209-9 (LSB) Image Inverse Scanner image Pulse processing PCB data 0 bit differential ISVD0...
Page 342 (CN802) (FP-D450/D600 Series) Signal Destination Status Function Name AGND LVPS CN16-6 Ground -12V2 LVPS CN16-5 DC-12V power supply -12V AGND LVPS CN16-4 Ground 12V2 LVPS CN16-3 DC+12V power supply LVPS CN16-2 Ground LVPS CN16-1 DC+5V power supply (FP-D450/D600 Series) (CN803) Signal Destination Status...
Page 343: So Dimm Pcb (Fp-D450/D600 Series)
4.21 SO DIMM PCB (FP-D450/D600 Series) (FP-D450/D600 Series) (CN301) Signal Destination Status Function Name System control Ground CN4-1 System control 3.3V DRAM data bus signal CN4-2 System control 3.3V DRAM data bus signal CN4-3 System control 3.3V DRAM data bus signal CN4-4 System control 3.3V...
Page 344 Signal Destination Status Function Name System control 3.3V DRAM address bus signal CN4-14 System control 3.3V DRAM address bus signal CN4-15 System control 3.3V DRAM address bus signal CN4-16 System control 3.3V DRAM address bus signal CN4-17 System control 3.3V DRAM address bus signal CN4-18 System control...
Page 345 Signal Destination Status Function Name System control 3.3V DRAM address bus signal CN4-28 System control 3.3V DRAM address bus signal CN4-29 System control 3.3V +3.3V DC+3.3V power supply CN4-30 System control 3.3V DRAM address bus signal CN4-31 System control 3.3V DRAM address bus signal CN4-32 System control...
Page 346 Signal Destination Status Function Name System control Column address control Pulse signal CAS3 CN4-42 System control Column address control Pulse signal CAS1 CN4-43 System control Pulse RAS0 Row address control signal CN4-44 System control Pulse RAS1 Row address control signal CN4-45 System control —...
Page 347 Signal Destination Status Function Name System control 3.3V DQ24 DRAM data bus signal CN4-56 System control 3.3V DQ25 DRAM data bus signal CN4-57 System control 3.3V DQ26 DRAM data bus signal CN4-58 System control 3.3V DQ28 DRAM data bus signal CN4-59 System control 3.3V...
Page 348 Signal Destination Status Function Name System control — — — CN4-70 System control — — — CN4-71 System control Ground CN4-72 4-227...
Page 349: Flash Dimm Pcb (Fp-D450/D600 Series)
4.22 16 M Flash DIMM PCB (FP-D450/D600 Series) (FP-D450/D600 Series) (CN351) Signal Destination Status Function Name System control Ground CN5-1 System control Flash memory address 3.3V bus signal CN5-2 System control Flash memory address 3.3V bus signal CN5-3 System control Flash memory address 3.3V bus signal...
Page 350 Signal Destination Status Function Name System control Flash memory address 3.3V bus signal CN5-14 System control Flash memory address 3.3V bus signal CN5-15 System control Flash memory address 3.3V bus signal CN5-16 System control 3.3V RD/BY Ready / busy check signal CN5-17 System control Write protection control...
Page 351 Signal Destination Status Function Name System control Flash memory address 3.3V bus signal CN5-28 System control Flash memory address 3.3V bus signal CN5-29 System control 3.3V +3.3V DC+3.3V power supply CN5-30 System control — — — CN5-31 System control Flash memory address 3.3V bus signal CN5-32...
Page 352 Signal Destination Status Function Name System control — — — CN5-42 System control — — — CN5-43 System control — — — CN5-44 System control — — — CN5-45 System control — — — CN5-46 System control Flash memory address 3.3V bus signal A16 *...
Page 353 Signal Destination Status Function Name System control Flash memory data bus 3.3V signal DQ12 CN5-56 System control Flash memory data bus 3.3V signal CN5-57 System control Flash memory data bus 3.3V signal DQ11 CN5-58 System control Flash memory data bus 3.3V signal CN5-59...
Page 354 Signal Destination Status Function Name System control Pulse CE * Chip select signal CN5-70 System control Flash memory address 3.3V bus signal CN5-71 System control Ground CN5-72 4-233...
Page 355: Lsu Image Data Control Pcb (Fp-D450/D600Series)
4.23 LSU Image Data Control PCB (FP-D450/D600Series) (CN1) (FP-D450/D600 Series) Signal Destination Status Function Name Image Processing Laser current control ENABLE0 PCB CN38-26 signal Image Processing CAL0 PWM calibration signal PCB CN38-25 Image Processing Laser A APC control ADJ10 PCB CN38-24 signal Image Processing Ground...
Page 356 Signal Destination Status Function Name Image Processing Pulse Laser A image data bit 5 PLDA5 PCB CN38-8 Image Processing Pulse NLDA5 Laser A image data bit 5 PCB CN38-7 Image Processing Pulse PLDA6 Laser A image data bit 6 PCB CN38-6 Image Processing Pulse NLDA6...
Page 357 Signal Destination Status Function Name Image Processing Pulse PLDB3 Laser B image data bit 3 PCB CN38-40 Image Processing Pulse NLDB3 Laser B image data bit 3 PCB CN38-39 Image Processing Pulse PLDB4 Laser B image data bit 4 PCB CN38-38 Pulse Image Processing NLDB4...
Page 358 (CNLSP) (FP-D450/D600 Series) Signal Destination Status Function Name Image Processing Ground PCB CN36-1 Pulse Image Processing LSU main scan LSULSYNC PCB CN36-2 synchronization signal Image Processing Ground PCB CN36-3 Image Processing DC+5V power supply PCB CN36-4 (CNLSM) (FP-D450/D600 Series) Signal Destination Status Function...
Page 359 4.24 Automatic Duplex Unit (ADU) Driver PCB (FP-D450/D600Series) (FP-D450/D600 Series) (CN651) Signal Destination Status Function Name Main CPU PCB DC+24Vpower supply CN11-2 Main CPU PCB PGND Power ground CN11-1 Main CPU PCB DC+24Vpower supply CN11-4 Main CPU PCB PGND Power ground CN11-3 Main CPU PCB Pulse...
Page 360 (CN652) (FP-D450/D600 Series) Signal Destination Status Function Name Paper detecting sensor Ground CN-3 Paper detecting Detecting sensor DXPESN Paper detecting signal CN-2 Paper detecting sensor DC+5V power supply CN-1 — — — — Paper pass sensor 2 Ground CN-3 Paper pass Paper pass sensor 2 sensor 2 paper detecting signal...
Page 361 (CN653) (FP-D450/D600 Series) Signal Destination Status Function Name Length guide Pulse motor DXLAB Motor drive signal A CN-5 Length guide Pulse motor DXLA Motor drive signal A CN-4 Length guide Pulse motor DXLB Motor drive signal B CN-3 Length guide motor DC+24V power supply CN-2...
Page 362 (CN654) (FP-D450/D600 Series) Signal Destination Status Function Name Paper feed clutch +12V2 Clutch drive signal CN-2 Paper feed clutch DC+24V power supply CN-1 ADU main Pulse motor DXMA Motor drive signal A CN-1 ADU main motor DC+24V power supply CN-3 ADU main Pulse motor...
Page 363 (CN655) (FP-D450/D600 Series) Signal Destination Status Function Name Paper length sensor Ground CN-3 Paper length Paper length guide sensor home position detecting PSLSN CN-2 signal Paper length sensor DC+5V power supply CN-1 — — — — Paper width sensor Ground CN-3 Paper width Paper width guide home...
Page 364: Low Voltage Power Supply Pcb (Fp-D450/D600Series)
4.25 Low Voltage Power Supply PCB (FP-D450/D600Series) (CN1/CN2) (FP-D450/D600 Series) Signal Destination Status Function Name AC 120V / AC 220 - Power cord 240V power supply AC 120V / AC 220 - Power cord 240V power supply (CN3) (FP-D450/D600 Series) Signal Destination Status...
Page 365 (CN6) (FP-D450/D600 Series) Signal Destination Status Function Name Main motor PGND Power ground CN1-2 Main motor Door SW open : 0V CN1-1 Door SW close : 24V DC+24V power supply Wait / Error : (CN7) (FP-D450/D600 Series) Signal Destination Status Function Name AC driver PCB...
Page 366 (CN10) (FP-D450/D600 Series) Signal Destination Status Function Name Main CPU PCB DC+12V power supply CN9-6 Main CPU PCB AGND Ground CN9-7 Main CPU PCB Ground CN9-8 Image processing Ground PCB CN206-1 Main CPU PCB DC+5V power supply CN9-9 Image processing DC+5V power supply PCB CN206-2 (CN11)
Page 367 (CN12) (FP-D450/D600 Series) Signal Destination Status Function Name PAPERVP CNSQ-1 DC+24V power supply PAPERVP CNSQ-2 DC+24V power supply PGND CNSQ-3 Power ground PGND CNSQ-8 Power ground (CN13) (FP-D450/D600 Series) Signal Destination Status Function Name PAPERVP CNSCN-1 DC+24V power supply PAPERVP CNSCN-2 DC+24V power supply PGND...
Page 368 (CN15) (FP-D450/D600 Series) Signal Destination Status Function Name Battery 12BT DC+16V power supply Battery Ground (CN16) (FP-D450/D600 Series) Signal Destination Status Function Name CCD PCB DC+5V power supply CN802-6 CCD PCB Ground CN802-5 CCD PCB DC+12V power supply CN802-4 CCD PCB AGND Ground CN802-3...
Page 369 (CN18) (FP-D450/D600 Series) Signal Destination Status Function Name HDD1/2 12V1 DC+12V power supply CNPHD1-1 HDD1/2 Ground CNPHD1-2 HDD1/2 Ground CNPHD1-3 HDD1/2 DC+5V power supply CNPHD1-4 (CN19) (FP-D450/D600 Series) Signal Destination Status Function Name HDD3/Zip 12V1 DC+12V power supply CNPHD1-1 HDD3/Zip Ground CNPHD1-2 HDD3/Zip...
Page 370 (CN20) (FP-D450/D600 Series) Signal Destination Status Function Name Image processing PCB 3.3V 3.3V DC+3.3V power supply CN204-1 Image processing PCB Ground CN204-2 Image processing PCB Ground CN204-3 Image processing PCB 5.1V DC+5.1V power supply CN204-4 Image processing PCB Ground CN204-5 Image processing PCB 12V1...
Page 371 (CN22) (FP-D450/D600 Series) Signal Destination Status Function Name Printer control 3.3V 3.3V DC+3.3V power supply PCB S1-1 Printer control Ground PCB S1-2 Printer control Ground PCB S1-3 Printer control 5.1V DC+5.1V power supply PCB S1-4 (CN23) Not used 4-250...
Page 372: High Voltage Power Supply Pcb (Fp-D450/D600 Series)
4.26 High Voltage Power supply PCB (FP-D450/D600 Series) (FP-D450/D600 Series) (CNHV) Signal Destination Status Function Name Main CPU PCB DC+24V power supply CN10-12 Main CPU PCB PGND Power ground CN10-11 Main CPU PCB Separation high voltage HVDCNT CN10-10 ON / OFF signal Main CPU PCB Separation high voltage Leak...
Page 373: Ac Drive Pcb (Fp-D450/D600 Series)
4.27 AC Drive PCB (FP-D450/D600 Series) (FP-D450/D600 Series) (CN201) Signal Destination Status Function Name AC 120V / AC 220 - Power switch 240V power supply (CN203) (FP-D450/D600 Series) Signal Destination Status Function Name Fuser AC 120V / AC 220 - DSAC1 thermostat 240V power supply...
Page 374 (CN206) (FP-D450/D600 Series) Signal Destination Status Function Name Main CPU PCB DC+5V power supply CN5-11 Main CPU PCB Fuser lamp ON / OFF HTTR1 CN5-9 signal Main CPU PCB Fuser lamp ON / OFF HTTR2 CN5-10 signal 4-253...
Page 375: Printer Controller Pcb (Option) (Fp-D450/D600 Series)
4.28 Printer Controller PCB (Option) (FP-D450/D600 Series) (FP-D450/D600 Series) (CNS1) stift- Signal Status Destination Function Name 3.3V 3.3V LVPS CN22-1 DC+3.3V power supply LVPS CN22-2 Ground LVPS CN22-3 Ground LVPS CN22-4 DC+5V power supply (CNJ1) (FP-D450/D600 Series) stift- Signal Destination Function Status Name...
Page 376 Signal Status Destination Function Name 3.3V SDRAM DIMM-13 Data 9 3.3V DQ10 SDRAM DIMM-14 Data 10 3.3V DQ11 SDRAM DIMM-15 Data 11 3.3V DQ12 SDRAM DIMM-16 Data 12 3.3V DQ13 SDRAM DIMM-17 Data 13 3.3V +3.3V SDRAM DIMM-18 DC+3.3V power supply 3.3V DQ14 SDRAM DIMM-19...
Page 377 Signal Destination Status Function Name 3.3V SDRAM DIMM-33 Address 0 3.3V SDRAM DIMM-34 Address 2 3.3V SDRAM DIMM-35 Address 4 3.3V SDRAM DIMM-36 Address 6 3.3V SDRAM DIMM-37 Address 8 3.3V SDRAM DIMM-38 Address 10 — SDRAM DIMM-39 — — 3.3V +3.3V SDRAM DIMM-40...
Page 378 Signal Status Status Destination Function Name — SDRAM DIMM-53 — — SDRAM DIMM-54 Ground 3.3V DQ16 SDRAM DIMM-55 Data 16 3.3V DQ17 SDRAM DIMM-56 Data 17 3.3V DQ18 SDRAM DIMM-57 Data 18 3.3V DQ19 SDRAM DIMM-58 Data 19 3.3V +3.3V SDRAM DIMM-59 DC+3.3V power supply 3.3V...
Page 379 Signal Destination Status Function Name 3.3V +3.3V SDRAM DIMM-73 DC+3.3V power supply 3.3V DQ28 SDRAM DIMM-74 Data 28 3.3V DQ29 SDRAM DIMM-75 Data 29 3.3V DQ30 SDRAM DIMM-76 Data 30 3.3V DQ31 SDRAM DIMM-77 Data 31 SDRAM DIMM-78 Ground CLK2 SDRAM DIMM-79 Clock 2 —...
Page 380 Signal Status Destination Function Name 3.3V DQ38 SDRAM DIMM-93 Data 37 3.3V DQ39 SDRAM DIMM-94 Data 38 3.3V DQ40 SDRAM DIMM-95 Data 39 SDRAM DIMM-96 Data 40 3.3V DQ41 SDRAM DIMM-97 Ground 3.3V DQ42 SDRAM DIMM-98 Data 41 3.3V DQ43 SDRAM DIMM-99 Data 42 SDRAM DIMM-...
Page 381 Signal Destination Status Function Name SDRAM DQM5 Data input/output mask 5 DIMM-113 SDRAM — — — DIMM-114 SDRAM -RAS Low address strove DIMM-115 SDRAM Ground DIMM-116 SDRAM 3.3V Address 1 DIMM-117 SDRAM 3.3V Address 3 DIMM-118 SDRAM 3.3V Address 5 DIMM-119 SDRAM 3.3V...
Page 382 Signal Status Destination Function Name SDRAM 3.3V +3.3V DC+3.3V power supply DIMM-133 SDRAM — — — DIMM-134 SDRAM — — — DIMM-135 SDRAM — — — DIMM-136 SDRAM — — — DIMM-137 SDRAM Ground DIMM-138 SDRAM 3.3V DQ48 Data 48 DIMM-139 SDRAM 3.3V...
Page 383 Signal Destination Status Function Name SDRAM 3.3V DQ56 Data 56 DIMM-153 SDRAM 3.3V DQ57 Data 57 DIMM-154 SDRAM 3.3V DQ58 Data 58 DIMM-155 SDRAM 3.3V Data 59 DQ59 DIMM-156 SDRAM 3.3V +3.3V DC+3.3V power supply DIMM-157 SDRAM 3.3V DQ60 Data 60 DIMM-158 SDRAM 3.3V...
Page 384 (CNJ2) (FP-D450/D600 Series) Signal Status Destination Function Name Network Card DC+5V power supply CNJ10-31 Network Card DC+5V power supply CNJ10-32 Network Card DC+5V power supply CNJ10-33 Network Card /CSP2 Card select signal 2 CNJ10-34 Network Card Data 15 CNJ10-35 Network Card Data 14 CNJ10-36 Network Card...
Page 385 Signal Destination Status Function Name Network Card Address 0 CNJ10-51 Network Card Data 7 CNJ10-52 Network Card Data 6 CNJ10-53 Network Card Address 15 CNJ10-54 Network Card Data 5 CNJ10-55 Network Card Address 14 CNJ10-56 Network Card Data 4 CNJ10-57 Network Card Address 13 CNJ10-58...
Page 386 Signal Status Destination Function Name Network Card /WAIT Wait signal CNJ10-11 Network Card Address 6 CNJ10-12 Network Card /CSP1 Card select signal 1 CNJ10-13 Network Card Address 5 CNJ10-14 Network Card — — — CNJ10-15 Network Card — — — CNJ10-16 Read Network Card...
Page 387 (CNJ4) (FP-D450/D600 Series) Signal Status Destination Function Name PC printer port Centronics /STB Strove signal connector 1 PC printer port Centronics DATA1 Data 1 connector 2 PC printer port Centronics DATA2 Data 2 connector 3 PC printer port Centronics DATA3 Data 3 connector 4 PC printer port...
Page 388 Signal Status Destination Function Name PC printer port Centronics — — — connector 15 PC printer port Centronics — — — connector 16 PC printer port Centronics Frame ground connector 17 PC printer port Printer connection Centronics detecting signal connector 18 PC printer port Centronics Ground...
Page 389 Signal Destination Status Function Name PC printer port Centronics Ground connector 29 PC printer port Centronics Ground connector 30 PC printer port Centronics /INIT Initialization signal connector 31 PC printer port Centronics /FAULT Error signal connector 32 PC printer port Centronics —...
Page 390 Signal Status Destination Function Name Main CPU PCB Ground CN203-7 Main CPU PCB Ground CN203-8 Main CPU PCB Ground CN203-9 Main CPU PCB Ground CN203-10 Main CPU PCB Ground CN203-11 Main CPU PCB Ground CN203-12 Main CPU PCB Ground CN203-13 Main CPU PCB Ground CN203-14...
Page 391 Signal Destination Status Function Name Main CPU PCB Ground CN203-27 Main CPU PCB Ground CN203-28 Main CPU PCB Ground CN203-29 Main CPU PCB Ground CN203-30 Main CPU PCB Image data receive /IDRDY CN203-31 ready signal Main CPU PCB /IDSTB Image data strove signal CN203-32 Main CPU PCB Ground...
Page 392 (CNJ8) (FP-D450/D600 Series) Signal Status Destination Function Name Printer Hard disk IDE bus /RESET Reset signal connector 1 Printer Hard disk IDE bus Ground connector 2 Printer Hard disk IDE bus DATA7 Data 7 connector 3 Printer Hard disk IDE bus DATA8 Data 8 connector 4...
Page 393 Signal Status Destination Function Name Printer Hard disk IDE bus DATA1 Data 1 connector 15 Printer Hard disk IDE bus DATA14 Data 14 connector 16 Printer Hard disk IDE bus DATA0 Data 0 connector 17 Printer Hard disk IDE bus DATA15 Data 15 connector 18...
Page 394 Signal Destination Status Function Name Printer Hard DMA transfer accept /DACK disk IDE bus signal connector 29 Printer Hard disk IDE bus Ground connector 30 Printer Hard Interrupt signal disk IDE bus connector 31 Printer Hard 16 bit I/O select signal /IOCS16 disk IDE bus connector 32...
Page 395: Network Card (Option) (Fp-D450/D600 Series)
4.29 Network Card (Option) (FP-D450/D600 Series) (CNJ2A) (FP-D450/D600 Series) Signal Destination Status Function Name 585mV~3.1V Ethernet cable -1 Transmit data + 585mV~3.1V Ethernet cable -2 Transmit data - 585mV~3.1V Ethernet cable -3 Receive data + — Ethernet cable -4 — —...
Page 396 Signal Status Destination Function Name Rizer card — — — CN601-A9 Rizer card DC+5V power supply CN601-A10 Rizer card — — — CN601-A11 Rizer card Ground CN601-A12 Rizer card Ground CN601-A13 Rizer card — — — CN601-A14 Rizer card RST# Reset CN601-A15 Rizer card...
Page 397 Signal Destination Status Function Name Rizer card AD_20 Address/data 20 CN601-A29 Rizer card Ground CN601-A30 Rizer card AD_18 Address/data 18 CN601-A31 Rizer card AD_16 Address/data 16 CN601-A32 Rizer card — — — CN601-A33 Rizer card FRAME# Cycle frame CN601-A34 Rizer card Ground CN601-A35 Rizer card...
Page 398 Signal Status Destination Function Name Rizer card Add in board detect RSNT#1 CN601-B9 signal 1 Rizer card — — — CN601-B10 Rizer card Add in board detect PRSNT#2 CN601-B11 signal 2 Rizer card Ground CN601-B12 Rizer card Ground CN601-B13 Rizer card —...
Page 399 Signal Destination Status Function Name Rizer card AD_21 Address /data 21 CN601-B29 Rizer card AD_19 Address/data 19 CN601-B30 Rizer card — — — CN601-B31 Rizer card AD_17 Address/data 17 CN601-B32 Bus command/byte Rizer card CBE#2 enable 2 CN601-B33 Rizer card Ground CN601-B34 Rizer card...
Page 400 (CNJ10) (FP-D450/D600 Series) Signal Status Status Destination Function Name Printer controller Data 2 PCB CNJ2-31 Printer controller Address 11 PCB CNJ2-32 Printer controller Data 1 PCB CNJ2-33 Printer controller Address 10 PCB CNJ2-34 Printer controller Data 0 PCB CNJ2-35 Printer controller Address 9 PCB CNJ2-36 Printer controller...
Page 401 Signal Destination Status Function Name Printer controller — — — PCB CNJ2-51 Printer controller Ground PCB CNJ2-52 Printer controller — — — PCB CNJ2-53 Printer controller — — — PCB CNJ2-54 Printer controller /INTPRT2 Interrupt signal 2 PCB CNJ2-55 Printer controller Ground PCB CNJ2-56 Printer controller...
Page 402 Signal Status Destination Function Name Printer controller Data 10 PCB CNJ2-11 Printer controller Ground PCB CNJ2-12 Printer controller Data 9 PCB CNJ2-13 Printer controller Data 8 PCB CNJ2-14 Printer controller /INTPRT1 Inerrupt signal 1 PCB CNJ2-15 Printer controller Ground PCB CNJ2-16 Printer controller Address 3 PCB CNJ2-17...
Page 403: Hard Disk Drive For Filing/Back-Up (Fp-D450/D600 Series)
4.30 Hard Disk Drive for Filing/Back-up (FP-D450/D600 Series) (CNSHD1/2) (FP-D450/D600 Series) Signal Destination Status Function Name System control Reset RESET Reset signal CN6-1 System control Ground CN6-2 HOST System control DATA 7 Hard disk data bus CN6-3 HOST System control DATA 8 Hard disk data bus CN6-4...
Page 404 Signal Destination Status Function Name HOST System control DATA 13 Hard disk data bus CN6-14 HOST System control DATA 1 Hard disk data bus CN6-15 HOST System control DATA 14 Hard disk data bus CN6-16 HOST System control DATA 0 Hard disk data bus CN6-17 HOST...
Page 405 Signal Destination Status Function Name System control — — — CN6-28 System control — — — CN6-29 System control Ground CN6-30 HOST System control Hard disk interrupt Pulse IRQ14 signal (15) CN6-31 HOST System control Hard disk 16 bit transfer IO16 control signal CN6-32...
Page 406 (CNPHD1/2) Signal Status Function Destination Name LVPS 12V1 DC+12V power supply CN18-1 LVPS Ground CN18-2 LVPS Ground CN18-3 LVPS DC+5V power supply CN18-4 4-285...
Page 407: Zip Drive (Fp-D450/D600 Series)
4.31 Zip Drive (FP-D450/D600 Series) (FP-D450/D600 Series) (CNSRMD) Signal Destination Status Function Name System control Reset RESET Reset signal CN6-1 System control Ground CN6-2 HOST System control DATA 7 Hard disk data bus CN6-3 HOST System control DATA 8 Hard disk data bus CN6-4 HOST System control...
Page 408 Signal Destination Status Function Name HOST System control DATA 13 Hard disk data bus CN6-14 HOST System control DATA 1 Hard disk data bus CN6-15 HOST System control DATA 14 Hard disk data bus CN6-16 HOST System control DATA 0 Hard disk data bus CN6-17 HOST...
Page 409 Signal Destination Status Function Name System control — — — CN6-28 System control — — — CN6-29 System control Ground CN6-30 HOST System control Hard disk interrupt Pulse IRQ14 signal (15) CN6-31 HOST System control Hard disk 16 bit transfer IO16 control signal CN6-32...
Page 410 (FP-D450/D600 Series) (CNPRMD) Signal Status Function Destination Name — — — — LVPS Ground CN19-2 LVPS Ground CN19-3 LVPS DC+5V power supply CN19-4 4-289...
Page 411: Image Processing Pcb (Fp-D450/D600 Series)
4.32 Image processing PCB (FP-D450/D600 Series) (CN19) (FP-D450/D600 Series) Signal Destination Status Function Name ADF connector Inverse ADF receive Pulse ISTRX CN-8 signal ADF connector Pulse STRX ADF receive signal CN-9 ADF connector Ground CN-10 ADF connector Inverse ADF transfer Pulse IADFTX CN-11...
Page 412 (CN25) (FP-D450/D600 Series) Signal Destination Status Function Name ADF timing sensor input Detecting signal ADFRRSN CN952-7 32 bit data receive input signal ADFIDI CN952-6 Ground CN952-9 32 bit data transfer / Pulse receive clock signal ADFICLK CN952-4 Data output enable signal ADFIENB CN952-2...
Page 413 (CN36) (FP-D450/D600 Series) Signal Destination Status Function Name LSU CNLSP-1 DC+5V power supply LSU CNLSP-2 Ground LSU main scan Pulse synchronization signal LSULSYNC LSU CNLSP-3 LSU CNLSP-4 Ground — — — — LSU CNLSA-2 Ground APC moniter terminal LSU CNLSA-3 Resolution select signal LSU CNLSA-4 Ground...
Page 414 (CN38) (FP-D450/D600 Series) Signal Destination Status Function Name LSU image data Image picture clock Pulse control PCB signal NLCLK0 CN1-a26 Image picture element LSU image data Pulse clock signal control PCB PLCLKO CN1-a25 LSU image data Pulse control PCB NLDA7 Laser A image data bit 7 CN1-a24 LSU image data...
Page 415 Signal Destination Status Function Name LSU image data Pulse control PCB NLDA1 Laser A image data bit 1 CN1-a12 LSU image data Pulse control PCB PLDA1 Laser A image data bit 1 CN1-a11 LSU image data Pulse control PCB NLDA Laser A image data bit 0 CN1-a10 LSU image data...
Page 416 Signal Destination Status Function Name LSU image data control PCB +5VL DC+5V power supply CN1-b24 LSU image data control PCB +5VL DC+5V power supply CN1-b23 LSU image data Pulse control PCB NLDB7 Laser B image data bit 7 CN1-b22 LSU image data Pulse control PCB PLDB7...
Page 417 Signal Destination Status Function Name LSU image data Pulse control PCB NLDB1 Laser B image data bit 1 CN1-b10 LSU image data Pulse control PCB PLDB1 Laser B image data bit 1 CN1-b9 LSU image data Pulse control PCB NLDB Laser B image data bit 0 CN1-b8 LSU image data...
Page 418 (CN43) (FP-D450/D600 Series) Signal Destination Status Function Name LVPS cooling fan motor PGND Power ground CN-3 LVPS cooling LVPS cooling fan motor Stop fan motor lock F signal PSFL Rotates CN-2 LVPS cooling LVPS cooling fan motor fan motor ON / OFF signal PRCFM1 CN-1 PGND...
Page 419 (CN201) (FP-D450/D600 Series) Signal Destination Status Function Name System control COM2 data terminal DTR2J PCB CN3-A01 ready signal System control +12V1 DC+12V power supply PCB CN3-A02 System control RTS2J COM2 request signal PCB CN3-A03 Pulse System control COM2 communication RxD2J PCB CN3-A04 input signal System control...
Page 420 Signal Destination Status Function Name System control PCI bus address data AD24 PCB CN3-A25 signal System control 3.3V +3.3V DC+3.3V power supply PCB CN3-A27 System control PCI bus address data AD22 PCB CN3-A28 signal System control PCI bus address data AD20 PCB CN3-A29 signal...
Page 421 Signal Destination Status Function Name System control PCI bus address data AD13 PCB CN3-A46 signal System control PCI bus address data AD11 PCB CN3-A47 signal System control Ground PCB CN3-A48 System control PCI bus address data AD09 PCB CN3-A49 signal System control Bus command / byte C/-BE0...
Page 422 Signal Destination Status Function Name System control DC+5V power supply PCB CN3-B06 Pulse System control Interrupt request signal INTA PCB CN3-A06 Pulse System control Interrupt request signal INTC PCB CN3-A07 System control Ground PCB CN3-B12 System control Ground PCB CN3-B13 System control Ground PCB CN3-B15...
Page 423 Signal Destination Status Function Name System control PCI bus address data AD19 PCB CN3-B30 signal System control 3.3V +3.3V DC+3.3V power supply PCB CN3-B31 System control PCI bus address data AD17 PCB CN3-B32 signal System control Bus command / byte C/-BE2 PCB CN3-B33 enable signal...
Page 424 Signal Destination Status Function Name System control PCI bus address data AD08 PCB CN3-B52 signal System control PCI bus address data AD07 PCB CN3-B53 signal 3.3V System control +3.3V DC+3.3V power supply PCB CN3-B54 System control PCI bus address data AD05 PCB CN3-B55 signal...
Page 425 (CN202) (FP-D450/D600 Series) Signal Destination Status Function Name Main CPU PCB Sub-scan direction GVSYNC CN34-1 synchronization signal Main CPU PCB Gate array chip select GIPGCS CN34-2 signal Main CPU PCB Pulse GIWR Gate array write signal CN34-3 Main CPU PCB GIRD Gate array read signal CN34-4...
Page 426 Signal Destination Status Function Name Main CPU PCB Pulse GAD1 Data bus CN34-20 Main CPU PCB Pulse GAD2 Data bus CN34-21 Main CPU PCB Pulse GAD3 Data bus CN34-22 Main CPU PCB Pulse GAD4 Data bus CN34-23 Main CPU PCB Pulse GAD5 Data bus...
Page 427 (CN203) (FP-D450/D600 Series) Signal Destination Status Function Name Printer controller Ground PCB CNJ5-1 Printer controller Ground PCB CNJ5-2 Printer controller Ground PCB CNJ5-3 Printer controller Ground PCB CNJ5-4 Printer controller Ground PCB CNJ5-5 Printer controller Ground PCB CNJ5-6 Printer controller Ground PCB CNJ5-7 Printer controller...
Page 428 Signal Destination Status Function Name Printer controller Ground PCB CNJ5-20 Printer controller Ground PCB CNJ5-21 Printer controller Ground PCB CNJ5-22 Printer controller Ground PCB CNJ5-23 Printer controller Ground PCB CNJ5-24 Printer controller Ground PCB CNJ5-25 Printer controller Ground PCB CNJ5-26 Printer controller Ground PCB CNJ5-27...
Page 429 Signal Destination Status Function Name Printer controller Image data 5 PCB CNJ5-40 Printer controller Image data 6 PCB CNJ5-41 Printer controller Image data 7 PCB CNJ5-42 Printer controller Ground PCB CNJ5-43 Printer controller Image data 8 PCB CNJ5-44 Printer controller Image data 9 PCB CNJ5-45 Printer controller...
Page 430 Signal Destination Status Function Name Printer controller Printer controller serial /SCPRN PCB CNJ5-58 data control signal Printer controller Ground PCB CNJ5-59 Printer controller Reset signal /RESET PCB CNJ5-60 (CN204) (FP-D450/D600 Series) Signal Destination Status Function Name 3.3V LVPS PCB 3.3V DC+3.3V power supply CN10-1 LVPS PCB...
Page 431 (CN205) Signal Destination Status Function Name Operation switch Switch signal Operation switch Ground Control panel Control panel CPU PCB communication receive PRTS CN401-11 control signal Control panel Control panel CPU PCB communication transfer PCTS CN401-12 control signal Control panel Control panel Pulse CPU PCB communication receive...
Page 432 (CN206) (FP-D450/D600 Series) Signal Destination Status Function Name LVPS PCB Ground CN10-4 LVPS PCB DC+5V power supply CN10-6 (CN208) (FP-D450/D600 Series) Signal Destination Status Function Name Fan motor ON/OFF PRCFM2 — signal Fan motor lock HDDFL — STOP ROTATE detecting signal PGND —...
Page 433 (CN209) (FP-D450/D600 Series) Signal Destination Status Function Name CCD PCB CN801-23 Ground CCD PCB CN801-24 Ground CCD PCB Scanner horizontal Pulse CN801-21 synchronization signal ISLSYNC_C CCD PCB CN801-22 Ground CCD PCB Return horizontal Pulse CN801-19 synchronizing signal IRLSYNC differential output CCD PCB Inverse return horizontal Pulse...
Page 434 Signal Destination Status Function Name CCD PCB Scanner image data 3 Pulse CN801-9 bit differential output SVD3 signal CCD PCB Inverse scanner image Pulse CN801-10 data 3 bit differential ISVD3 output signal CCD PCB Scanner image data 4 Pulse CN801-7 bit differential output SVD4 signal...
Page 435 (FP-D450/D600 Series) (CN210) Signal Destination Status Function Name CCD PCB Ground CN803-7 CCD PCB Ground CN803-8 CCD PCB Pulse Scanner D/A converter DADATA CN803-5 data CCD PCB Ground CN803-6 CCD PCB Pulse Scanner D/A converter DACLK CN803-3 clock CCD PCB Ground CN803-4 CCD PCB...
Page 436 (CN212) (FP-D450/D600 Series) Signal Destination Status Function Name Main CPU PCB Printer condition change CN4-1 detection signal Main CPU PCB PRDY Printer ready signal CN4-2 Main CPU PCB VRDY VSYNC receive signal CN4-3 Main CPU PCB Paper feed completion PACK CN4-4 signal Main CPU PCB...
Page 437 Signal Destination Status Function Name Pulse Main CPU PCB Scanner horizontal SLSYNC CN4-17 synchronization signal Main CPU PCB Shading compensation CN4-18 standard data SHRDY completion signal Main CPU PCB SREQ Scanner request CN4-19 Main CPU PCB Pulse ZCSP Host zero cross signal CN4-20 Main CPU PCB Pulse...
Page 438 (CN213) (FP-D450/D600 Series) Signal Destination Status Function Name Pulse Main CPU PCB CPU enable signal CN213-1 Main CPU PCB BRIW Read/write select signal CN213-2 Pulse IPC circuit chip select Main CPU PCB MB38CS signal CN213-3 IPC communication Main CPU PCB IPRXD receive signal CN213-4...
Page 439: Troubleshooting
Section V Troubleshooting 5.1 Service Mode In Service mode, the technician can check for abnormalities in the copier so the copier can always operate normally. The input/output of major components in every section can be checked. 1. Service mode functions Service Item Function...
Page 440 Service Item Function Remarks mode Continuous copying 1. Multi copies are made 1. Total and electronic when the Start key is counter are disabled. pressed. 2. If paper is in drawer, the 2. Duplex mode (1 sided misfeed circuit is original to 2 sided copy or enabled.
Page 441: Service Mode Procedure
2. Service mode procedure 1) To select the service mode The service mode is selected when USER PRESET, Multi-Copy key 3 and Original size Ledger/A3 keys are simultaneously pressed, then F1 will appear in the display. (If copier is abnormal, then F4 will appear in the display.) 2) To reset the service mode The service mode is reset when USER PRESET and CLEAR keys are pressed simultaneously.
Page 442 Message display Code Function Condition 7 6 5 4 3 2 1 0 a) Paper limit sensor 2 Paper is full. b) Paper limit sensor 1 Paper is full. a) Registration roller paper pass Paper is not detected. sensor b) Duplex unit paper length Paper length guide in home guide home position sensor position.
Page 443 Message display Code Function Condition 7 6 5 4 3 2 1 0 a) Developer unit detecting Developer unit is not sensor detected. b) Copier paper feed door open/ Door is opened. close sensor c) Sheet bypass paper detecting Paper is not detected. sensor d) Sheet bypass paper size Sensor is ON.
Page 444 Message display Code Function Condition 7 6 5 4 3 2 1 0 a) System console detecting System console is detected. sensor b) System console paper level Paper is empty or tray is sensor 3 (lower tray) pulled out. c) System console paper level Paper is empty or tray is sensor 2 (middle tray) pulled out.
Page 445 Message display Code Function Condition 7 6 5 4 3 2 1 0 a) 2 bin finisher stapler cartridge Cartridge is installed. detecting sensor b) 2 bin finisher stapler detecting Stapler is detected. sensor c) 2 bin finisher stapler home Stapler in home position.
Page 446 Message display Code Function Condition 7 6 5 4 3 2 1 0 For FA-A355 a) ADF open / close sensor ADF is closed. b) Face up paper exit sensor Original is not detected. c) Original detecting sensor Original is not detected. d) ADF detecting sensor 1 ADF is installed.
Page 447 Press the Start key to start and press the key to reset. Stop Code Item Function Not used Sheet bypass paper feed clutch (FP-D250/D350) When CN29-2 becomes 0V from +24V, clutch operates. (FP-D450/D600) When CN29-2 becomes 0V from +24V, clutch operates.
Page 448 Code Item Function Middle roller clutch (FP-D250/D350) When CN6-10 becomes 0V from +24V, clutch operates. (FP-D450/D600) When CN6-10 becomes 0V from +24V, clutch operates. Recycle solenoid (FP-D250/D350) When CN3-12 becomes 0V from +24V, solenoid operates. (FP-D450/D600) When CN3-12 becomes 0V from +24V, solenoid operates.
Page 449 Code Item Function Polygon motor (FP-D250/D350) When CN32-4 becomes 0V from +24V, motor rotates. (FP-D450/D600) When CN32-6 becomes 0V from +24V, motor rotates. Registration roller clutch (FP-D250/D350) When CN29-4 becomes 0V from +24V, clutch operates. (FP-D450/D600) When CN29-4 becomes 0V from +24V, clutch operates.
Page 450 Code Item Function Ozone / suction fan (FP-D250/D350) When CN6-1 is +24V, ozone / suction fan rotates. Dust collecting fan When CN6-7 is +24V, dust collecting fan rotates. Exhaust fan motor 4 When CN6-2 is +24V, exhaust fan 4 rotates.
Page 451 Code Item Function Lift up motor 2 (FP-D250/D350) (System console middle) When CN604-1 is +24V, motor rotates lifting up. (FP-D450/D600) When CN604-1 is +24V, motor rotates lifting up. (together with upper limit control) Paper feed clutch 2 (FP-D250/D350) (System console middle) When CN609-3 becomes 0V from +24V, clutch operates.
Page 452 Code Item Function LCC paper feed solenoid (FP-D250/D350) When CN564-2 becomes 0V from +24V, solenoid operates. (FP-D450/D600) When CN564-2 becomes 0V from +24V, solenoid operates. LCC paper feed tray lift (up) (FP-D250/D350) When CN563-1 is +24V, motor rotates lifting up.
Page 453 0V, lamp lights up. (FP-D450/D600) c123 Not used ~149 c150 +24V output control (Scanner) (FP-D250/D350) When signal is sent from main CPU CN1-1 LVPS, +24V is supplied to +24V line (FP-D450/D600) When signal is sent from main CPU CN1-1...
Page 454 Code Item Function c152 Optics fan motor 1 (FP-D250/D350) When CN17-3 becomes 0V fan motor rotates. (FP-D450/D600) When CN17-3 becomes 0V fan motor rotates. c153 Not used ~159 c160 Paper transport belt motor forward The motor rotates forward (High speed)
Page 455: F5 Mode Copier Function Programming
4. F5 mode Copier function programming Set the copier to service mode and press Multi-Copy key "5". Press the Start key. Select the desired code number with touch panel display and touch the OK key. If you wish to select other code number, scroll the menu with arrow keys ( Select desired function with touch panel display and touch the OK key.
Page 456 Code Function Item (Factory setting) Not used Copy paper size 0: None 1: A3 10 (for North setting 2: B4 3: A4 American) (copier paper tray 4: A4R 5: B5 1 (for European/ upper) 6: B5R 7: A5 Others) 8: FLS 1 9: FLS 2 10: Ledger 11: Legal...
Page 457 Code Function Item (Factory setting) Duplex unit 0: Cancellation of duplex unit 1: Duplex unit installation automatically discriminated Total copy count 0: Does not count up In case of mis-feed in 1: Count up second side copy for two side copy, copy number is/not counted.
Page 458 Code Function Item (Factory setting) Key counter and 0: Not installed Departmental counter 1: Key counter installed 2: Departmental counter Key counter count up same as F5-c41 timing Counter count up 0: Does not count up (Interleaving, cover 1: Count up mode) Hole punch default 0: Off...
Page 459 Void at N in 1 mode 0: No 1: Yes Preventive 0: No call maintenance 1: 1.5K 2: 2.5K 3: 5K 10 (FP-D250) 4: 10K 5: 15K 6: 20K 7: 30K 8: 40K 9: 60K 10: 80K 11: 90K 12: 120K...
Page 460 Code Function Item (Factory setting) Not used PC print out priority 0: Priority 1: No priority Not used PC print pages 0: Document 1: Page Original detection size 0: Fixed size (Invoice/A5 to Ledger/A3) judgment detection 1: Letter/A4 or less defaults to Letter/ User information list Determines whether to print Password password print...
Page 461 Code Function Item (Factory setting) Not used Beep sound 0: None 1: Yes c91* Check size M1 Y Width of paper parallel position to paper feed direction c92* Check size M1 X Length of paper vertical position to paper feed direction c93* Check size M2 Y Width of paper parallel position to paper...
Page 462: F6 Mode Adjustment And Programming
5. F6 mode Adjustment and programming Set the copier to service mode and press Multi-Copy key "6". Press the Start key. Select the desired code number with touch panel display and touch the OK key. If you wish to select other code number, scroll the menu with arrow keys ( The display will indicate current setting.
Page 463 Code Function Item Remarks Copy paper registration After c04 is adjusted, 0.2625mm detecting timing delay time is adjusted (–30 to +20) from timing roller clutch (+): Delayed (–): Advanced Not used Registration void of After c05 is adjusted, 0.425mm image registration void should (0 to +99) be adjusted.
Page 464 Code Function Item Remarks Toner density sensor Adjustment of toner 0.033V gain voltage density sensor gain (–69 to +40) (standard = 6.51V) voltage c22- Not used Toner density sensor Adjustment of toner 19.5mV judgment voltage level supply starting (–26 to +26) (standard = 2.5V) judgment voltage level.
Page 465 Text / Photo mode (–) : Darker, (+) : Lighter Photo mode Image density (–99 to +99) image density adjustment for Photo mode (–) : Darker, (+) : Lighter” Not used *FP-D250/D350/D450, D600 (Copy function) only. 5-27...
Page 466 Code Function Item Remarks CCD detection timing Adjustment of CCD 0.2mm read position (–42 to +20) Registration void of Adjustment of 0.5mm image registration void. (0 to +99) (During use with ADF FA-A888 = No swing back condition) Auto image density in Adjustment of Auto (–99 to +99) the Text mode...
Page 467 Code Function Item Remarks c67- Not used LCD contrast Reference voltage 60mV adjustment adjustment for LCD (–45 to +18) contrast (+) Darker (–) Lighter Coordinates Coordinates 0.5mm compensation for touch compensation value (–128 to +127) panel (X1) (X1 point) (+) Left (–) Right Coordinates Coordinates...
Page 468 Code Function Item Remarks Laser Unit image side Laser write start 0.5 mm to side position adjustment (–4 to +4) (side to side adjustment) For FP-D450/D600 (–8 to +8) Server connection port Server connection port (0 to +255) number (1) number =256 x Server connction port number(2) (F6-c86) +...
Page 469 Code Function Item Remarks Not used F5/F6 Initialization Reset to factory default (Factory use only) (F6 values will be set to "0".) 5-31...
Page 470: F7 Mode Electronic Counter
6. F7 mode electronic counter 1. Read procedure (Example : Code No.2 Total count) Set the copier to service mode and press Multi-Copy key "7". Electronic counter access F7 Press the Start key. Electronic counter access C00 All list print out Key operator ID code Total count PM count...
Page 471 2. Reset/write procedure (Example : Code No.2 Total count) Set the copier to service mode and press Multi-Copy key "7". Electronic counter access F7 Press the Start key. Electronic counter access C00 All list print out Key operator ID code Total count PM count Developer count...
Page 472 Code Function Item All list print out Prints each counter and their readings in one sheet. Procedure : (1) Select the F7-00 code. (2) Select ‘Yes’ to print out the list. (3) Press the start key. A code No. for Key Operator Identification code number for access to counter mode in the User choice.
Page 473 Code Function Item Service count Accumulated total count expressed the following formula. Service count = Copy print count (code 21) X a + DD file print count (code 27) X b + Printer print count (code 23) X c + DD file save/retrieve count (code 22+code 25) X d + ADF original feed count (code 06) X e +...
Page 474 Departmental counter mode 1. Setting up the user access codes 1) Activate the departmental mode by F5-42. 2) Input a 3 digit key operator access code in the F7-01. 3) Exit the service mode. 4) Press the User Preset key and select General function.
Page 475: F8 Mode Copier Operation Adjustment
7. F8 mode copier operation adjustment Set the copier to service mode and press Multi-Copy key "8". Press the Start key. Select the desired code number with Multi-Copy key. Press the Start key to initiate the adjustment procedure. Press Clear and User Preset key to escape service mode. Code Function Item...
Page 476 Code Function Item Black density sensor reference (Need special adjustment jigs) level adjustment (Factory use only) Black density sensor output gain This adjustment should be performed when adjustment installing the copier, cleaning / replacing the black density sensor or replacing the drum. Procedure: a) Press the Start key.
Page 477: F9 Mode System Administration
8. F9 mode System Administration Set the copier to service mode and press Multi-Copy key "9". Press the Start key. Select the desired code number with Multi-Copy key. Press Clear and User Preset key to escape service mode. Code Item Function Telephone number input Displays the contact number when the...
Page 478: Self-Diagnostics / Machine Malfunctions
5.2 Self-diagnostics / Machine Malfunctions The self-diagnostic functions detect troubles in the important components of the copier. When any trouble occurs, the copier is stopped. 1. User error NOTE: UXX will appear in the message display. Code Item See page Key counter not installed (option) or Access code 5-41 number was not input...
Page 479 3) Key counter connector is shorted or broken. 4) Key counter is defective. 5) LVPS connector is shorted or broken. 6) LVPS is defective. 7) (FP-D250/D350) CPU PCB connector (CN14) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN14) is shorted or broken.
Page 480 4) Duplex unit driver PCB connector is shorted or broken. 5) Duplex unit driver PCB is defective. 6) LVPS connector is shorted or broken. 7) LVPS is defective. 8) (FP-D250/D350) CPU PCB connector (CN11) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN11) is shorted or broken.
Page 481 7) ADF CPU PCB is defective. 8) LVPS connector is shorted or broken. 9) LVPS is defective. 10) CPU PCB connector (CN19/25) is shorted or broken. (FP-D250/D350) 11) Image processing PCB connector (CN19) is shorted or broken. (FP-D450/D600) 12) CPU PCB is defective.
Page 482 4) Toner empty sensor connector is shorted or broken. 5) Toner empty sensor is defective. 6) LVPS connector is shorted or broken. 7) LVPS is defective. 8) (FP-D250/D350) CPU PCB connector (CN12) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN12) is shorted or broken.
Page 483: Paper Jam
2. Paper Jam Code Jam Position Paper Feed unit System Console Paper Transport unit Fuser unit / Exit unit Duplex unit Finisher Inverting unit/Inverting shift tray 5-45...
Page 484 Code Contents position The registration roller paper pass sensor does not detect paper within a predetermined time after sheet bypass paper feed roller starts rotating. The copier upper paper feed unit paper pass sensor 1 does not detect paper within a predetermined time. When the duplex unit is not installed: After copier upper stage paper feed roller starts rotating.
Page 485 Code Contents position Paper feeding from copier lower stage: The copier lower stage paper pass sensor 2 is detecting paper within a predetermined time after first detecting paper. Paper feeding from optional system console upper stage: Upper stage paper pass sensor 1 is detecting paper within a predetermined time after first detecting paper.
Page 486 Code Contents position The paper exit sensor does not detect paper within a predetermined time C, D after registration roller starts rotating. The paper exit sensor is detecting paper within a predetermined time after sensor detected paper. The paper exit sensor is detecting paper. J43-49 Not used Transport operation for duplexing The duplex unit paper pass sensor 1 does not detect paper within a...
Page 487 Code Contents position a) The ADF exit paper pass sensor does not detect paper within a predetermined time after ADF starts paper exit. b) The ADF exit paper pass sensor is detecting paper within a predetermined time after sensor detected paper. c) The ADF exit paper pass sensor is detecting paper before using ADF.
Page 488: Machine Error
3. Machine error The machine system will detect problems in the important areas of the copier. When any problem occurs, the copier stops. Error codes indicate the mode number and the code number which are alternately displayed in the "Digit" display area of the touch panel. When there is trouble in any part of the copier, the "MACHINE ERROR TURN POWER SW OFF/ON"...
Page 489 E3: Developer unit and hopper unit error Code Function See page E3-01 Toner bottle motor rotation 5-56 E3-03 Toner density sensor gain 5-56 E3-10 High voltage power supply leak (1) 5-57 E3-11 High voltage power supply leak (2) 5-57 E3-12 High voltage power supply leak (3) 5-57 E3-20...
Page 490 Code Function See page E5-43 Printer controller hard disk access 5-63 E5-44 Printer controller DIMM 5-63 E5-50 I/O communication error 5-64 E5-60 Power supply cooling fan motor rotation 5-64 E5-61 Printer controller fan motor rotation 5-64 E5-89 Printer controller LSI access 5-65 E6: Duplex unit error Code...
Page 491 (3) Home position sensor connector is shorted or broken. (4) Home position sensor is defective. (5) LVPS connector is shorted or broken. (6) LVPS is defective. (7) (FP-D250/D350) CPU PCB connector (CN20) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN20) is shorted or broken.
Page 492 (2) CCD PCB is defective. (3) LVPS connector is shorted or broken. (4) LVPS is defective. (5) CPU PCB connector (CN209/210) is shorted or broken. (FP-D250/D350) (6) Image Processing PCB connector (CN209/ 210) is shorted or broken. (FP-D450/D600) (7) CPU is defective.
Page 493 (6) Paper feed driver PCB connector is shorted or broken. (7) Paper feed driver PCB is defective. (8) LVPS connector is shorted or broken. (9) LVPS is defective. (10) (FP-D250/D350) CPU PCB connector (CN7/22/23) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN7/22/23) is shorted or broken.
Page 494 (6) System console driver PCB connector is shorted or broken. (7) System console driver PCB is defective. (8) LVPS connector is shorted or broken. (9) LVPS is defective. (10) (FP-D250/D350) CPU PCB connector (CN7) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN7) is shorted or broken.
Page 495 (4) HVPS connector is shorted or broken. (5) HVPS is defective. (6) LVPS connector is shorted or broken. (7) LVPS is defective. (8) (FP-D250/D350) CPU PCB connector (CN10) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN10) is shorted or broken.
Page 496 (1) Fan motor connector is shorted or broken. (2) Fan motor is defective. (3) LVPS connector is shorted or broken. (4) LVPS is defective. (5) (FP-D250/D350) CPU PCB connector (CN6) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN6) is shorted or broken.
Page 497 (6) Fuser thermostat is defective. (7) Fuser lamp is defective. (8) AC driver PCB connector is shorted or broken. (9) AC driver PCB is defective. (10) (FP-D250/D350) LVPS connector (CN4) is shorted or broken. (FP-D450/D600) LVPS connector (CN4) is shorted or broken.
Page 498 Code No. Check points Function E5-04 Vp (+12V) (1) (FP-D250/D350) LVPS connector (CN10/11/17) is shorted or broken. (FP-D450/D600) LVPS connector (CN10/11/17) is shorted or broken. (2) LVPS is defective. (3) (FP-D250/D350) CPU PCB connector (CN9) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN9) is shorted or broken.
Page 499 (1) ADF connector is not securely connected. (2) Copier CPU PCB connector (CN19 / 25) is shorted or broken. (FP-D250/D350) (3) Image Processing PCB connector (CN19) is defective. (FP-D450/D600) (4) Copier CPU PCB is defective. (5) ADF CPU PCB connector is shorted or broken.
Page 500 Control panel CPU PCB connector (CN401) is shorted or broken. (4) Control panel CPU is defective. (5) CPU PCB connector (CN205) is shorted or broken. (FP-D250/D350) (6) Image Processing PCB connector (CN205) is shorted or broken. (FP-D450/D600) (7) CPU is defective.
Page 501 (1) The total counter is not securely connected. (2) Total counter is defective. (3) LVPS connector is shorted or broken. (4) LVPS is defective. (5) (FP-D250/D350) CPU PCB connector (CN12) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN12) is shorted or broken.
Page 502 (6) System console paper feed driver PCB is defective. (7) LCC driver PCB connector is shorted or broken. (8) LCC driver PCB is defective. (9) (FP-D250/D350) CPU PCB connector (CN12) is shorted or broken. (FP-D450/D600) CPU PCB connector (CN12) is shorted or broken.
Page 503 (2) Sensor is defective. (3) Paper length motor connector is shorted or broken. (4) Paper length motor is defective. (5) (FP-D250/D350) ADU driver PCB connector (CN653/655) is shorted or broken. (FP-D450/D600) ADU driver PCB connector (CN653/655) is shorted or broken.
Page 504 Check points Function E6-05 Paper detecting sensor (1) Sensor connector is shorted or broken. (2) Sensor is defective. (3) (FP-D250/D350) ADU driver PCB connector (CN652) is shorted or broken. (FP-D450/D600) ADU driver PCB connector (CN652) is shorted or broken. (4) ADU driver PCB is defective.
Page 505 (1) Motor connector is shorted or broken. (2) Motor is defective. (3) Finisher controller PCB connector (CN- J10) is shorted or broken. (4) Finisher controller PCB is defective. (5) (FP-D250/D350) LVPS connector (CN8) is shorted or broken. (FP-D450/D600) LVPS connector (CN8) is shorted or broken.
Page 506 (1) Motor connector is shorted or broken. (2) Motor is defective. (3) Finisher controller PCB connector (CN- J11) is shorted or broken. (4) Finisher controller PCB is defective. (5) (FP-D250/D350) LVPS connector (CN8) is shorted or broken. (FP-D450/D600) LVPS connector (CN8) is shorted or broken.
Page 507 J11) is shorted or broken. (4) Finisher controller PCB is defective. (5) Finisher relay PCB connector (CN-J301/ 302/305) is shorted or broken. (6) Finisher controller PCB is defective. (7) (FP-D250/D350) LVPS connector (CN8) is shorted or broken. (FP-D450/D600) LVPS connector (CN8) is shorted or broken.
Page 508 Function E7-26 Finisher back up RAM data (1) Finisher controller PCB connector is shorted or broken. (2) Finisher controller PCB is defective. (3) (FP-D250/D350) LVPS connector (CN8) is shorted or broken. (FP-D450/D600) LVPS connector (CN8) is shorted or broken. (4) LVPS is defective.
Page 509 (1) Motor connector is shorted or broken. (2) Motor is defective. (3) Inverting unit PCB connector (CN601/604) is shorted or broken. (4) Inverting unit PCB is defective. (5) (FP-D250/D350) LVPS connector (CN13) is shorted or broken. (FP-D450/D600) LVPS connector (CN13) is shorted or broken.
Page 510 (1) Motor connector is shorted or broken. (2) Motor is defective. (3) Inverting unit PCB connector (CN601/603) is shorted or broken. (4) Inverting unit PCB is defective. (5) (FP-D250/D350) LVPS connector (CN13) is shorted or broken. (FP-D450/D600) LVPS connector (CN13) is shorted or broken.
Page 511: User Preset Mode
5.3 User Preset Mode 1. Operation procedure: 1) General user menu (1) Press the User Preset key on the control panel. (2) Select the desired User Preset Function with LCD touch panel. (3) Select the desired User Preset Mode with LCD touch panel. (4) Select the desired contents and touch the OK key according to LCD message.
Page 512 6) Touch the cassette key until the paper size required is shown. Ledger/A3 Legal/B4 Letter/A4 Invoice/A5 LetterR/A4R 7) When the paper size setting is completed, touch the OK key. 8) Touch the OK key on the LCD menu. The LCD menu will be changed to initial menu of the Key Operator Mode. 5-74...
Page 513 General Code Item Function Factory setting US00 Finisher mode default 0 Nonsort 1 Sort 2 Sort/Staple 3 Group US01 Staple position default 0 Front 1 Rear 2 Booklet US02 Power on default mode 0 Copy 1 Filing US03 Manual add toner 0 OFF 1 ON US04...
Page 514 General (Key operator) Code Item Function Factory setting US00 Paper size 0 Not use 1 A3 2 B4 3 A4 4 A4R 5 B5 6 B5R 7 A5 8 FLS1 9 FLS2 10 LEDGER 11 LEGAL 12 LETTER 13 LETTER-R 14 INVOICE US01 Auto reset time...
Page 515 Code Item Function Factory setting US04 Language default 0 English/German/ English or Japanese German 1 French/Swedish/English 2 Spanish/Italian/Dutch US05 Special paper tray 1 0 None 1 Copier (upper) 2 Copier (lower) 3 System console (upper) 4 System console (middle) 5 System console (lower) 6 LCC 7 Sheet bypass US06...
Page 516 Code Item Function Factory setting US16 User registration Registers user to copier US17 User delete Delete user registration US18 User information change Changes user information registered US19 ID card change Changes ID card information registered US20 Date and time setting US21 Not used Not available...
Page 517 Code Item Function Factory setting US38 User information list 0 Stop 1 Start 5-79...
Page 518 Copier (General) Code Item Function Factory setting US00 Margin value default 0 5 mm 1 10 mm 2 15 mm 3 20 mm US01 Edge value default 0 5 mm 1 10 mm 2 15 mm 3 20 mm US02 Book value default 0 15 mm 1 20 mm...
Page 519 Copier (Key operator) Code Item Function Factory setting US00 Auto exposure default 0 Not detecting 1 Auto mode priority 2 Manual mode priority US01 Original mode default 0 Text mode 1 Photo mode 2 Text/Photo mode US02 Photo mode contrast 0 Weak 1 Medium 2 Strong...
Page 520 Code Item Function Factory setting US14 Text mode sharpness 0 Weak 1 Medium 2 Strong US15 High speed duplex mode 0 No 1 Yes US16 Memory overflow warning 0 Print 1 Cancel US17 Document save default 0 No 1 Yes 5-82...
Page 521 File Code Item Function Factory setting US00 DD code retrieve 0 No 1 Yes US01 Cover sheet default 0 Normal 1 Thumbnail US02 File retrieve default 0 Normal 1 Thumbnail US03 Cover retrieve default 0 Normal 1 Thumbnail US04 Resolution default 0 600 dpi 1 300 dpi 2 200 dpi...
Page 522 File (Key operator) Code Item Function Factory setting US00 Save access rights 0 Individual 1 Group 2 Public US06 Attribute retrieve 0 No 1 Display US09 Attributes manage 0 No 1 Display US10 Auto exposure default 0 Not detecting 1 Auto mode priority 2 Manual mode priority US11 Original mode default...
Page 523 Printer (General) Code Item Function Factory setting US00 PCL menu 0 Font 0~44 1 Symbol set 0~35 2 Pitch 0~999 3 Point size 40~9995 4 Line/inch 100~4800 5 Return character CR+LF US01 PostScript menu Not available (option) US02 Job menu 0 Resolution 600 dpi 300 dpi...
Page 524 Printer (Key operator) Code Item Function Factory setting US00 HDD spool area format 0 None 1 128 MB 2 256 MB 3 512 MB US01 Spool function 0 No 1 Yes US02 Flash ROM update accept 0 No 1 Yes US03 Dump list mode 0 Transfer...
Page 525: Program Update
5.4 Program Update 1. Update procedure of the Printer controller SIMM NOTE: When the printer hard disk (FA-HD01) is installed, change the spool function setting in the user preset mode (code us01 in the printer key operator mode) to 'No' before proceeding.
Page 526 16) Transfer the new file data to be updated using copy command in the binary mode . (Example) >copy /b {FILE NAME} LPT1 FILE NAME of the SIMM program. When the program runs the copier data lamp will flash. The PC will return to DOS prompt in about 2 minutes. Data update will be completed approximately one minute after DOS prompt returns.
Page 527: Unpacking/Installation
Section VI Unpacking/Installation 6. 1 Precautions on Set Up Copy machine performance and the copy quality is subject to and dependant on environmental conditions. To maintain good performance, quality, and safe operation, observe the following precautions: 1) For safe operation and to avoid trouble do not install the system under the following conditions: •...
Page 528: Unpacking
6.2 Unpacking Check the condition and contents of the box for completeness or any shipping damage before installation. (Visual check)
Page 529: Installation Procedure
6.3 Installation Procedure • Remove the external packing/protection materials. • Remove the shipping tape. Note: Save the shipping materials for future use (Transport of copier) Caution: Make sure the copier is unplugged before the installation. Location Shipping material/Procedure Check 1. Optical unit (1) Remove the optical unit shipping screws.
Page 530 Location Shipping material/Procedure Check Paper transport unit (1) Open the front door. (2) Remove the shipping tape. Tape Fuser unit (1) Open the paper exit door. (2) Open the fuser exit guide plate. (3) Remove the fuser pressure release screws. (2 screws) (4) Close the fuser exit guide plate.
Page 531 Location Shipping material/Procedure Check Installing the developer (1) Remove the developer unit lid. (2) Shake the bottle of developer thoroughly. (3) Pour the developer evenly into the developer unit. Make sure to empty the bottle. (4) Reinstall the developer unit lid. (5)-1.
Page 532 Location Shipping material/Procedure Check FP-D250/D350/D350H: Turn the power switch ON FP-D450/D600: (1) Open the front door. (2) Turn the power switch ON then close the front door. (3) Turn the operation switch ON. TDC adjustment (1) Press the “User Preset”, “Ledger/ A3 of Original Size”...
Page 533 Location Shipping material/Procedure Check Toner bottle insertion (1) Open the front door. (2) Take a fresh bottle of toner and shake it 10 to 15 times. Hopper (3) Swing the toner bottle hopper open 90 degrees. (4) Remove the toner bottle cap. (5) Insert the toner bottle into the hopper unit and turn it clockwise until the arrows on the bottle and...
Page 534 Additional procedure for FP-D350H (FP-D350H only) Location Check Shipping material/Procedure (1) Remove the copier rear cover. (7 screws) (1) Remove the copier top right cover. (2 screws) (2) Remove the pre-stamped knock out from the top right cover. (1) Install the Zip drive unit. (3 screws)
Page 535 Location Shipping material/Procedure Check (1) Remove the Zip drive disk cover. (2 screws) (1) Install the support bracket to both the Zip drive unit and the copier. (3 screws) (1) Connect the IDE signal harness to IDE connector CN7 on the sys- tem control PCB.
Page 536: Adjustment
6.4 Adjustment Location Shipping material/Procedure Check Exposure standard adjustment • The following values will be added to the reference value. DO NOT adjust these codes in the field. F6-17: G r i d s t a n d a r d v o l t a g e compensation F6-18: Laser power compensation F6-19: Developer bias standard...
Page 537 Location Shipping material/Procedure Check Side to side adjustment 1. Sheet bypass tray Screw (1) L o o s e n a d j u s t i n g s c r e w s . (2 screws) (2) Move the adjusting plate to the front or rear accordingly.
Page 538 Note 2 : 1) Refer to optional accessories service manual in order to install optional accessories. 2) When the FA-A888 is installed onto FP-D250/D350 series, connector position of the main CPU PCB needs to be changed, For details, refer to the FA-A888 Installation Procedure...
Page 539: Printer Unit/Dd Filing Unit Mounting Kit (Fa-Pk30)
(visual check) * Check the contents of the box. Printer controller Control panel (x2) Fan motor (x1) mounting bracket (x1) (For FP-D250/D350) (For FP-D250/D350) Control panel (C) PCB Control panel (D) PCB Hard disk drive mounting (x1)
Page 540 Insulation sheet 2 Fan motor mounting (x1) (x1) screw (x2) Screw (M3 x 6) Screw (M3 x 6) Locking wire saddle Mini clamp (x1) (x8) (x6) (x5) (For FP-D250/D350) Power supply harness 3 Seal (x2) (for printer controller) (x1) 6-14...
Page 541 (2) Installation procedure Remove all shipping materials/tape before the installation. Caution: Make sure the copier is unplugged before the installation. Location Shipping material/Procedure Check (1) Remove the copier rear cover. (7 screws) (1) Remove the rear cover mounting bracket. (paper exit side) (2 screws) (1) Connect the power harness 1 onto...
Page 542 Location Shipping material/Procedure Check (1) FP-D250/D350 Install the printer controller mount- ing bracket (4 screws). (2) Install the locking wire saddles. (x4: FP-D250/D350) (x3: FP-D450/D600) (3) Install the mini clamp. (x1) For FP-D250/D350 (1) Install the low voltage power sup- ply cooling fan onto the printer controller mounting bracket.
Page 543 Location Shipping material/Procedure Check (1) Open the front door. (2) Remove the control panel mount- ing screws. (2 screws) (3) Remove the blind cover and screw. (1) Connect the control panel (C) PCB harness to the control panel (C) PCB. (2) Connect the control panel (D) PCB harness to the control panel (C) PCB.
Page 544 Location Shipping material/Procedure Check (1) Connect the control panel (D) harness to the control panel (D) PCB. (2) Install the control panel (D) PCB onto the control panel. (2 screws) (1) Remove the control panel cover Note:Unhook the 3 positions of For filing the control panel cover to remove.
Page 545: Printer Unit (Fa-Pc350) / Multi Pdl Controller (Fa-Mc350)
6.6 Printer Unit (FA-PC350) / Multi PDL Controller (FA-MC350) (1) Unpacking Check the contents and condition of the box for completeness and any shipping damage before installation. (visual check) * Check the contents of the box. Printer controller PCB Mounting bracket Fan motor (x1) (x1) (x1)
Page 546 (2) Installation Remove all shipping materials before installation. Caution: Make sure the copier is unplugged before installation. Location Shipping material/Procedure Check (1) Install the SIMM PCB onto the printer controller PCB. (outer slot). (2) Install the mounting bracket. (2 screws) (3) Install the printer memory.
Page 547 Location Shipping material/Procedure Check (1) Install the printer controller PCB onto the bracket (7 screws, 1 con- nector). (2) Connect the power supply con- nector. (x1) (3) Reassemble in reverse order. 6-21...
Page 548: Network Adapter Card For Ethernet (Fa-Ne35)
6.7 Network Adapter Card for Ethernet (FA-NE35) (1) Unpacking Check the contents and condition of the box for completeness and any shipping damage before installation. (visual check) * Check the contents of the box. NAC PCB (x1) NAC harness (x1) NAC PCB mounting bracket (x1) Mounting screws...
Page 549 (2) Installation Remove all shipping materials before installation. Caution: Make sure the copier is unplugged before installation. Location Procedure Check (1) Install the NAC PCB to the its mounting bracket. (2 screws) (1) Remove the rear cover. (7 screws) (1) Remove the blind plate. (1 screw) (2) Remove the system control PCB.
Page 550 Location Procedure Check (1) Install the Riser card PCB onto the system control PCB. (2) Reinstall the system control PCB. (3) Install the NAC PCB onto the riser card PCB. (1) Install the mounting screws. (2 screws) Perform following procedures only when the printer controller is in- stalled.
Page 551 6.8 Hard Disk Drive for Printer (FA-HD01) (1) Unpacking Check the contents and condition of the box for completeness and any shipping damage before installation. (visual check) * Check the contents of the box. Hard Disk Drive for IDE signal harness for Hard Disk Drive mounting printer (x1) Hard Disk Drive (x1)
Page 552 (2) Installation procedure Remove all shipping materials before installation. Caution: Make sure the copier is unplugged before the installation. Location Shipping material/Procedure Check (1) Remove the copier rear cover. (7 screws) (1) Remove the hard disk mounting bracket. (right) (2 screws) (1) Install the printer hard disk drive.(4 screws) (1) Connect the IDE signal harnesses...
Page 553: Dd Filing Unit (Fa-Wa01/Wa02)
6.9 DD filing unit (FA-WA01/WA02) (1) Unpacking Check the contents and condition of the box for completeness and any shipping damage before installation. (visual check) * Check the contents of the box. Zip drive (x1) Zip support bracket Zip support bracket (x1) cover (x1) Hard disk drive (x1)
Page 554 IDE signal harness for IDE signal harness for Personal card (x10) Zip drive (x1) filing hard disk drive (x1) Zip drive mounting Zip support bracket Zip support bracket screw (M3 x 6) (x 3) mounting screw cover mounting screw (M3 x 6) (x 3) (M3 x 6) (x 2) Hard disk drive mounting Battery bracket...
Page 555 (2) Unpacking Remove all shipping materials before installation. Caution : Make sure the copier is unplugged before the installation. Location Procedure Check (1) Remove the copier rear cover. (7 screws) (2) Remove the cable cover (Plastic). (2 screws) (1) Remove the copier top right cover. (2 screws) (2) Remove the pre-stamped knock out from the top right cover.
Page 556 Location Procedure Check (1) Remove the Zip drive disk cover. (2 screws) (1) Install the support bracket to both the Zip drive unit and the copier. (3 screws) (1) Connect the IDE signal harness to IDE connector CN7 on the sys- tem control PCB.
Page 557 Location Procedure Check (1) Remove the hard disk mounting bracket. (right) (2 screws) Note : This bracket is for the printer hard disk drive. (FA-HD01) (2) Remove the hard disk mounting bracket. (left) (2 screws) (1) Install the hard disk drive in the rear compartment (4 screws).
Page 558 Location Procedure Check (1) Connect the IDE signal harness to IDE connector on the filing hard disk drive. (2) Connect the ground wire to the hard disk mounting bracket. (1) Attach the caution label (small) onto the battery. Label (small) (North America/Europe only) Battery (1) Install the battery mounting...
Page 559 Location Procedure Check (1) Install the card reader onto its mounting bracket. (2 screws) (2) Connect the card reader harness. (1) Open the front door. (2) Remove the control panel mount- ing screws. (2 screws) (3) Remove the blind cover and screw.
Page 560 Location Procedure Check (1) Turn on the power switch. (2) Press the “User Preset”, “Ledger/ A3 of Original Size” and “3” keys simultaneously to enter the service mode. (3) Press the “9” key to enter the F9 mode. (4) Press the Start key. (5) Select F9 mode code “03”.
Page 561: Hard Disk Driver For Back Up (Fa-Hd02)
6.10 Hard disk drive for back up (FA-HD02) (1) Unpacking Check the contents and condition of the box for completeness and any shipping damage before installation. (visual check) * Check the contents of the box. Hard Disk Drive for backup Hard Disk Drive mounting (x1) screw (M3 x 6) (x4)
Page 562 Location Shipping material/Procedure Check (1) Remove the hard disk mounting bracket. (right) (2 screws) Note: When the hard disk drive for printer (FA-HD01) is already installed. Remove IDE harness and power harness for the hard disk, then remove the mounting bracket.
Page 563: Hard Disk Driver For Image Memory (Fa-Hd03/Hd04)
6.11 Hard disk drive for Image memory (FA-HD03/HD04) (1) Unpacking Check the contents and condition of the box for completeness and any shipping damage before installation. (visual check) * Check the contents of the box. Hard disk drive (x1) IDE signal harness for Backup battery (x1) hard disk drive (x1) Battery mounting...
Page 564 (2) Installation procedure Remove all shipping materials before installation. Caution : Make sure the copier is unplugged before the installation. Location Procedure Check (1) Remove the copier rear cover. (7 screws) (1) Remove the hard disk mounting bracket. (right) (2 screws) Note : This bracket is for the printer hard disk drive.
Page 565 Location Procedure Check (1) Connect the ground wire to the hard disk mounting bracket. (1) Attach the caution label (small) onto the battery. Label (small) (North America/Europe only) Battery (1) Install the battery mounting bracket onto the copier. (4 screws) (1) Install the battery and connect the connector.
Page 566 Location Procedure Check (1) Attach the caution label (large) onto the copier rear cover. (North America only) Label (large) 6-40...
Page 567: Network, Printing, Copying And Imaging Terms
Section VIl Glossary of Terms Network, Printing, Copying and Imaging Terms A/D Converter Is an Analog to Digital Converter. Generic term for any device that changes continuous wave (analog) activity to binary (digital) code, or vise versa. Modems, CCDs and Faxes are A/D converters. Adobe Type Manager Software from Adobe Systems for Macintoshes that eliminates jagged edges on screen fonts and allows inexpensive (non apple) laser printers to reproduce PostScript fonts accurately and clearly.
Page 568 AppleTalk A seven- layer protocol stack developed by Apple for communications between its Apple Macintosh product range. Apple defines it in similar terms to the functionality of the seven-layer OSI model Application Layer The top layer in the OSI Reference Model comprising the interface between the OSI environment and a user’s application.
Page 569 Asynchronous communications A method of transmitting data in which each transmitted character is sent separately. The character has integral start and finish start and stop bits so that the character can be sent at an arbitrary time, and separate from any other character. It is the most rudimentary type of communication as the originating and receiving machines do not have to be synchronized.
Page 570 Back end The server part of a client/server application. It provides services across the network that have been requested by the client. For example, a back end may be a database server that responds to SQL requests from a workstation running a front end application.
Page 571 10BaseT A form of Ethernet and IEEE 802.3 network cabling using twisted pair cabling. It refers to 10Mbit/s speed Baseband transmission twisted pair cable with a maximum segment length of 100m. 100BaseT IEEE standard from proposals by the Fast Ethernet Alliance (including 3Com and SynOptics).
Page 572 Bitmap Strictly speaking, a bitmap is a resolution dependant computer file usually a scan, but perhaps a file from a paint program in which each pixel contains one bit of tonal information. In practice, people donít limit the use of the term bitmap to single bit per pixel images.
Page 573 Broadband Also referred to as wideband. A term describing any network that multiplexes multiple, independent network carrier frequencies on to a single cable. It allows multiple simultaneous “conversations”, since the independent networks operate on different frequencies and do not interfere with each other. In LAN terminology, it refers to a system in which multiple channels access a medium, for example co-axial cable, that has a large bandwidth using Radio Frequency (RF) modems.
Page 574 Byte Eight bits forming a unit of data. Usually each byte stores one character. Cache Pronounced cash. Small portion of high speed memory used for temporary storage of frequently used data. Reduces the time it would take to access that data, since it no longer has to be retrieved from disk.
Page 575 CD-ROM Compact Disc Read Only Memory. A data storage system using CDs as the medium. CD-ROMs hold more than 600MB of data. Centronics interface A parallel interface with 36 pins that will transmit eight data bits simultaneously. The interface originates from the Centronics Company, a printer manufacturer.
Page 576 Cluster A group of terminals or workstations on the same system. CMOT (CMIP/CMIS over TCP) The use of SO CMIP/CMIS network management protocols to manage gateways in a TCP/IP Internet. CMOT is a co-recommended standard with SNMP. Co-axial cable A cable comprising a central wire surrounded by a second tubular screening of fine wire.
Page 577 Connectionless Service The transport of a single datagram or packet of information from one network node to a destination node or multiple nodes without establishing a network connection. Contention The process whereby multiple users make requests for transmission bandwidth across a transmission link but the pool of bandwidth is less than the aggregate amount of bandwidth the users could request between them.
Page 578 D/A Converter Digital to Analog converter, Generic term for any device that changes digital (binary) pulses into continuous wave (analog) signals. Modems, Faxes, CCDs are D/A converters. Data compression A way of reducing the amount of data to be transmitted by applying one of severs techniques that reduce the number of bits needed to represent the information.
Page 579 Data Link Layer Two of the ISO OSI model is responsible for the transmission of information over a physical medium. After establishing the link it ensures the error- free delivery of the information through the use of error detection, error recovery and flow control.
Page 580 Digital signal A signal with only two values, normally 0 and 1, during transmission, unlike an analog signal whose values constantly vary. Digitize To convert an image or other data into a digital representation that may be processed electronically. You digitize a photograph when you scan it to copy. Direct attachment The IBM term for linking a device or LAN directly to a host computer through an appropriate Control Unit, like a cluster controller.
Page 581 DMA (Direct Memory Access) A technique for high-speed data transfer between a device such as LAN network adapter card and the computer memory. DMA bypasses the Central Processing Unit of the computer, PC or workstation, allowing the device to transfer a block of information directly across the bus into system memory. DMI (Desktop Management Interface) A set of APIs outlined by the DMTF, comprising three components: service layer, component interface and management interface.
Page 582 DPA (Demand Protocol Architecture) A technique for loading protocol stacks dynamically as they are required. It is associated with adapter cards in workstations and servers. Only the protocol stacks that are needed for a particular communications sessions are loaded. Examples of stacks that could be loaded include TCP/IP, XNS, SPX/IPX and NetBios.
Page 583 Dynamic routing A process for selecting the most appropriate path or route for a packet or datagram to travel around a network. At the end of each leg of the journey of the packet across the network the router decides on the most appropriate path for the packet or datagram to follow if there are multiple routes available.
Page 584 Electronic Overlay A collection of constant data known as a form that is electronically composed in the host processor and may be merged with variable data on a sheet during printing. Energy Star Compliant A printer that is Energy Star compliant will default into low wattage state as specified by the Environmental Protection Agency (EPA) when not printing, thus consuming less power.
Page 585 Error control A means of ensuring that information received across a transmission link is correct. The techniques involved typically use error detection to detect if the transmitted data has been corrupted. The error control technique involves asking for data to be retransmitted until a correct version is received. Ethernet The most widely LAN transmission network.
Page 586 Fast packet switching A WAN technology capable of transmitting data, digitized voice and digitized image information. It makes use of short, fixed length packets (or cells) that are all the same size. The underlying switching technology is based on the statistical multiplexing of data and voice in fixed length cells.
Page 587 File server A computer, attached to a LAN, that runs a Network Operating System (NOS). This lets the file server regulate communications among the workstations connected to it across the LAN, and to manage shared resources available on the file server, such as hard disk storage and printers. A file server may be dedicated: the computer is used only as a file server;...
Page 588 Foirl (Fiber Optic Inter-Repeater Link) Defined in IEEE 802.3 and implemented over two fiber links, transmit and receive, this medium may be up to 500m and 1 kilometer long depending on the number of repeaters in the network. Fractional services Bandwidth available from carriers in increments of 64Kbit/s, such as Mercury’s Switchband.
Page 589 Full Text Search The ability to search text files for occurrences of certain words, digits, sentences or patterns of characters. Fuser The part of the printing system that forces the toner to adhere to the paper. There are several types of fusing systems heat, chemical and pressure. Gamma A measure of contrast in photographic images.
Page 590 Gradient In graphics, having an area smoothly blend from one color to another, or from black to white, or vise versa. Group In the context of network security, a group is a set of users who share common permissions for one or more resources. Individually assigned user permissions take precedence over those assigned through groups.
Page 591 HDLC (High level Data Link Control) An ISO standard set of protocols for carrying data over a link with error and flow control. Similar to IBM’s SDLC, versions of HDLC are under development for multipoint lines. The ITU-TS later adapted HDLC for its Link Access Protocol used for X.25 networks.
Page 592 IAB (Internet Activities Board) The technical body that sets policy and standards for TCP/IP and the connected Internet suite of protocols. Its task forces are the IETF and IRTF. IBMCS (IBM Cabling System) Cabling system introduced by IBM in 1984 based around Shielded Twisted Pair (STP) cabling.
Page 593 IEEE 802.6 The standard that defines Mans, an SMDS-based, short packet ATM transmission. Image The computerized representation of a picture or graphic. Imaging Recording human readable images, pictures, images, motion, text, etc., into machine readable formats Imaging System Collection of units that work together to capture and recreate images.
Page 594 Internet address An IP address assigned in blocks of numbers to user organizations accessing the Internet by the US DoD’s Network Information Center. Duplicate addresses can cause major headaches on the network, but the NIC trusts organizations to use individual addresses responsibly. Each address is an eight- bit number (0 to 255).
Page 595 IP (Internet Protocol) The TCP/IP standard protocol that defines the IP datagram as the unit of information passed across an Internet and provides the basis for connectionless packet delivery service. IP includes the ICMP control and error message protocol as an integral part. It provides the functional equivalent of ISO OSI Network Services.
Page 596 JPEG (Joint Photographic Experts Group) Originally the name of a committee for graphics standards developed, co-sponsored by the International Organization for Standards (ISO) and the International Telecommunications Union- Telecommunications (ITU-T). The bit-mapping graphics file standard developed by this committee is also called JPEG and is widely used on the Internet. Generally a JPEG graphic is compressed at a higher rate (e.g.
Page 597 LAN Network Manager IBM’s network management software for Token Ring networks. LAN Segment A part of a LAN that is separated from the rest by one or more bridges. LAN Server IBM version of IBM LAN Manager. LAP (Link Access Protocol) The Data Link or OSI Layer Two protocol specified by the ITU-TS for the X.25 interface standard.
Page 598 Link state algorithm A routing algorithm such as OSPF which takes into account lowest delay when choosing a route: link speed and congestion as well as hop count. LLC (Logical Link Control) A data link protocol based or HDLC, developed for LANs by the IEEE 802 Committee and consequently common to all LAN standards for Data Link OSI Layer Two transmission.
Page 599 Lossy Methods of image compression, such as JPEG, that reduces the size of an image by disregarding some pictorial information. MAC (Media Access Control) layer A sub-layer of the Data Link Layer (Level Two) of the ISO OSI Model responsible for media control. Mailbox A printer or copier document output device that collects organizes output documents into individual bins.
Page 600 Matrix switching A form of data switching at the heart of ATM, enabling the appropriate bandwidth to be available end-to-end for the duration of the session without contention. MAU (Medium Attachment Unit) A transceiver (transmitter/receiver) comprising hardware circuitry that provides the correct electrical or optical connection between the computer and IEEE 802.3 LAN media.
Page 601 Microwave Wireless transmission at very high frequency to deliver telecommunications services, including TV distribution, between two points. It is dependent on line of sight. MIPS Millions of Instructions Per Second. A measure of computer speed. MIS (Management Information System) The person or group in a company who manages a company's entire computer system, including installed LANs, WANs and or mainframe computers.
Page 602 Multimedia Generic description of the generation and transfer of voice/data/video traffic between users. Applications to exploit multimedia to the full are emerging in the wake of advanced switching techniques and develop merits in desktop and server processing architectures. It may be essential to a physically separated group that communicates as if it was physically networked.
Page 603 NETBLT (Network Block Transfer) A Transport Level, flow controlled, bulk data transfer protocol used with TCP/IP internets. NETBLT controls the rate at which data is sent to allow a steady, high speed flow, Netlogon service A LAN Manager service that implements logon security. This service verifies the user name and password supplied by each user logging on to the local area network.
Page 604 Network device driver A program that enables the operating system software to communicate the network adapter cards. Also a software module running on a host or workstation that is responsible for the communications between the computer and the network or a device attached to the network. Network Interface Board An interface device installed in a computer to connect to a local network.
Page 605 Nodes Devices on a network that demand or supply services or where transmission paths are connected. Node is often used instead of workstation. NOS (Network Operating System) The software that connects all the devices on a network so that resources can be shared efficiently and files can be transferred. It handles administration of all network functions, Network operating systems are usually in two parts;...
Page 606 OEM (Original Equipment Manufacturer) The maker of equipment marketed by another vendor, usually under the name of the reseller. The OEM may make only certain components or complete devices, which can then be configured with software and/or hardware by the reseller. Off-line Something not presently active or available for access in a system.
Page 607 Packet A collection of bits, including the address, data and control, that are switched and transmitted together. The terms frame and packet are often used synonymously. Packet Buffer Memory space reserved for storing a packet awaiting transmission or for storing a received packet. Packet Switching A method of switching data in a network.
Page 608 PCL (printer command language) A page description language developed by Hewlett -Packard. It is sometimes referred to as HP PCL. Numerous versions of PCL exist, including PCL5c for color. Photoconductor A metallic substance, used in eletophotographic printers, that conducts and retains electrical charges until they are exposed to light. Ping A protocol for testing whether a particular computer is connected to the Internet by sending a packet to its IP address and waiting for a response.
Page 609 Print Server A computer and/or software to provide users or a network with access to a central printer. The printer server acts as a buffer, holding the information to be printed out in memory until the printer is free. It is possible to program the printer server to print jobs in the order they arrive or to give priority to particular users who, in effect, jump the queue.
Page 610 PCM (Pulse Code Modulation) One of the most common ways of converting an analog signal to a digital signal. This is done by sampling the signal and coding the sample. It usually samples at 8,000 times per second; each sampling representing 8bits.
Page 611 Protocol converter A device that translates between two protocols to facilitate communications between different computers or different systems. Qbit (Qualifier bit) In X.25 networks, bit 8 in an octet of packet header. It is used to indicate if a packet contains control information. Queue A stream of tasks or data waiting in line to be executed.
Page 612 Redirect A packet switching function that routes a call to an alternative network address if the link to the original address is not working. It is carried out by end point switches. Recommended Monthly Volume The maximum number of pages for which the machine is recommended for use with each one month period, as rated by the manufacturer.
Page 613 Resident Fonts The printers standard typefaces and, for laser printers the standard point sizes and print orientations for each typeface. For example, Courier 10, 12 (P/ L) means that the typeface Courier is available in sizes 10 point and 12 point and in portrait and landscape modes.
Page 614 ROM (Read Only Memory) Nonevolatile memory that can be read but not changed. Router Network interconnector device operating at OSI Network Layer (Level Three) that supports a particular Network Layer protocol and related stack, such as TCP/IP, DecNet, XNS, SNA, OSI IP, IPX. These days routers tend to support multiple protocols by a variety of methods, such as Protocol Independent Routing.
Page 615 Scanner A electronic device that optically senses human readable images, and works with software in the computer to convert the image to machine readable code for you to view. SCSI (small computer system interface) pronounced skuzzy. This high speed interface enables users to simultaneously connect several peripherals, such as printers, scanners, CD-ROM, and DVD devices to a SCSI interface on a computer.
Page 616 SMB (Server Message Block) A Microsoft - originated distributed system which enables access to another computer’s files and peripherals over the network as if they were local. SMTP (Simple Mail Transfer Protocol) The TCP/IP standard protocol for transferring electronic mail messages from one machine to another. SMTP specifies how two mail systems interact and the format of control messages they exchange to transfer mail.
Page 617 Source Routing IEEE standard for 802.5 Token Ring environments from an IBM development. A workstation (source) determines the router through the LAN internetwork. It sends a “discovery” or explorer packet along all active paths in the network, eventually reaching the destination host. Once received, the packet is sent back to the originator.
Page 618 Subnet Mask IP address style mask bits used for routing operations. A Subnet Mask defines how sub-segments of a network are treated. Usually, a router is used to mediate communications inside and outside a local network. However, when a LAN is divided into several "Subnets", data sent to another Subnet is relayed by a router, just as if between remote networks.
Page 619 TCP (Transmission Control Protocol) The standard transport level protocol that provides the full duplex, stream service on which many application protocols depend. TCP allows a process or one machine to send a stream of data to a process on another. Software implementing TCP usually resides in the operating system and uses the IP to transmit information across the network.
Page 620 TIFF (Tagged Image File Format) A platform independent file standard for graphic information. A TIFF file records an image as a group of dots (bit mapping), and can contain a halftone image. This standard has several variations, so in some cases, a TIFF file may not be readable by TIFF supporting software.
Page 621 TP-4/IP A term given to the ISO protocol suite that closely resembles TCP/IP. Transceiver - A communications device and software capable of transmitting and receiving (see also MAU). Transmission block - A sequence of continuous data characters or bytes transmitted as a unit, over which a coding procedure is usually applied for synchronous or error control purposes.
Page 622 Twisted Pair Two insulated copper wires twisted together with the twists or lays varied in length to reduce potential signal interference between the pairs. Where cables comprise more than 25 pairs, they are usually bundled and wrapped in a cable sheath. Twisted pair is the most common medium for connecting phones, computers and terminals to PABXS.
Page 623 UTP (Unshielded Twisted Pair) The standard cabling used for telephone lines. The standard IEEE 802.3, 10BaseT, defines use of Ethernet over UTP for rates up to 10Mbit/s. The general LAN medium of choice for the 1990s, UTP is marketed in brands such as AT&T’s PDS (Systimax) and OSCA.
Page 624 Wiring closet Location, usually a physical box in which the cabling on a particular floor is terminated, typically in a wiring frame. Wiring frame Used to organize and manage the termination and connection of multiple cables. Windowing Generic method of displaying data on screen, mimicking looking at several pieces of paper at once.
Page 625 Workflow automation The flow of documents around an organization in a prescribed order (workflow) can be automated, delivering an hierarchical and controlled form of workgroup computing. Workgroup computing - Method of organizing a business around productive teams using computer support to enable cooperative working and to eliminate time/space restrictions.
Page 626 Z-fold A sheet of paper folded back and fourth into three panels. Zoom To magnify a image for viewing or editing.\Gloss 7-60...
Page 627 TORANO-MAKI ORDER NO. OED9902357C1 FP-D250/D350 The Ninja's Torano-maki Schematic Diagram Important safty notice Componentes identified by head mark have special charac teristtics Open important for safty. When replace any of these components. Use CN19 CN362 Control CN13 only manufacturer's specified parts.
Page 628 TORANO-MAKI ORDER NO. OED9906370C1 FP-D450/D600 Series Schematic Diagram The Ninja’s Torano-maki CN362 Control Panel CN405 CN18 CN10 CLMBB HVLKC /CD1 (OPTION) HVCNT Control Panel B /RCP CN14 CLMB GREF /RDD Control Panel CLMA HVBCNT /CLS CN351 BREF CLMAB HVLKT CN360 HVTCNT CN402 CLSN...
Page 644 mRD8 mRD0 mRD1 mRD2 mRD3 mRD4 mRD5 mRD6 mRD7 mRAMOE# mRAMWE# mRE0# mRA0 mRA1 mRA2 mRA3 mRA4 mRA5 mRA6 mRA7 mRA8 mRA9 mRA10 mRA11 mRA12 mRA13 mRA14 cRD0 cRD1 cRD2 cRD3 cRD4 cRD5 cRD6 cRD7 cRAMOE# cRAMWE# cRE0# cRA0 cRA1 cRA2 cRA3 cRA4...
Page 659 4-3. Low Voltage Power Supply (3) CH10A07 ERF5EKR10S EEUFA1V102E ECUV1H104KBW 2SB1240TV2R R148 ERJ6GEYJ222V ERF5EKR10S ERJ6GEYJ683V ECA1HHG470B EEUFA1V102E R145 R136 ERJ6GEYJ824V 2SA1037KT146 2SJ374 ZD20 ECJ2VB1E104K MTZJ5.1BT77 FA7617CP CH28E36 1SS133T77 R146 R129 3.3V ERJ6GEYJ564V ERJ6GEYJ103V FA7617CP R144 ECUV1H104KBW ERJ6GEYJ332V EEUFA1V471E ECUV1H104KBW C100 ECKDHT471KC ECUV1H104KBW C120...
Page 660 5. AC Driver Circuit 5-1. AC Driver Circuit PCB (1) (for North America) IMPORTANT SAFETY NOTICE THE PARTS WITH MARK ON THIS SCHE- MATIC DIAGRAM INCORPORATE SPECIAL FEATURES IMPORTANT FOR SAFETY. WHEN SERVICING, IT IS ESSENTIAL THAT ONLY MANUFACTURER'S SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE PARTS WITH MARK OF THE SCHEMATIC.
Page 661 5-1. AC Driver PCB (1) (for Europe/others) IMPORTANT SAFETY NOTICE THE PARTS WITH MARK ON THIS SCHE- MATIC DIAGRAM INCORPORATE SPECIAL FEATURES IMPORTANT FOR SAFETY. WHEN SERVICING, IT IS ESSENTIAL THAT ONLY MANUFACTURER'S SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE PARTS WITH MARK OF THE SCHEMATIC.
Page 662 5-2. AC Driver PCB (2) IMPORTANT SAFETY NOTICE THE PARTS WITH MARK ON THIS SCHE- MATIC DIAGRAM INCORPORATE SPECIAL FEATURES IMPORTANT FOR SAFETY. WHEN SERVICING, IT IS ESSENTIAL THAT ONLY MANUFACTURER'S SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS IN THE PARTS WITH MARK OF THE SCHEMATIC.

This manual is also suitable for:

D350 D450 D600 Fp-d350 Fp-d450 Fp-d600

Panasonic FP-D250 User Manual

Warning

Introduction

Sub Assemblies

Preventive Maintenance

IV. PCB Connector and Signal Information

Troubleshooting

Unpacking/Installation

Vil. Glossary of Terms

Quick Links

Related Manuals for Panasonic FP-D250

Summary of Contents for Panasonic FP-D250

This manual is also suitable for:

Table of Contents