Page 3
Safety and Notice The DVP14 DVI output Cascadable Video Wall Processor, 4-Display Dual-View has been tested for conformance to safety regulations and requirements, and has been certifi ed for international use. However, like all electronic equipment, the DVP14 should be used with care.
Table of Contents INTRODUCTION.............3 FEATURES...............4 SPECIFICATIONS............5 PACKAGE CONTENTS..........6 INPUTS AND OUTPUTS...........6 SUPPORTED RESOLUTION..........7 HARDWARE INSTALLATION..........9 Installation Procedures ........10 Connection Diagram ........11 OPERATION SOFTWARE..........12 System Requirement and Precautions ..12 Instruction of Software Connection ..12 Instruction of Software Operation .....13 USING THE TV WALL CALCULATOR………………….17 TROUBLESHOOTING...........21 WARRANTY..............22...
255 by 255 squares. Virtually any setup for the display layout may be possible by the provided software. The DVP14 allows you to manipulate two input videos, in any position and whatever sizes you want for viewing. The embedded scaler converts signals from the two input sources to match the native resolution of monitors, flat panel displays, and/or projectors.
Features ● Four DVI outputs from 640x480 to 1920x1200 ● Local DVI loop output for monitoring the DVI input only ● Supports HDMI, DVI, S-Video, CVBS, Component, and VGA input, from 640x480 to 1920x1200, interlaced or progressive ● Advanced video de-interlacing for improving 480i and 576i SD video input ●...
Specifications Model Name DVP14 Technical Typical usage Video-wall processor Output displays Input Format HDMI / DVI / VGA / YPbPr / S-Video / CVBS Support [One digital and one analog can be used in PIP or PAP mode] Output Support...
● 1x DVI to VGA adapter Inputs and Outputs The DVP14 can use up to two inputs at one time and supports multiple in- put interfaces (HDMI, DVI, composite, S-Video, component, VGA (adapters needed)) and accepts both graphics and video signals, which come from computers and NTSC / PAL video sources respectively.
Page 10
Digital Visual Interface (DVI) to HDMI Female The unit has DVI-I Female connectors for Input and Outputs: DVI-I [29-pin Female, digital only] Recommended Adapter Connector you can use from DVI to HDMI Female DVI-I (Dal Link) to HDMI Female ...
Hardware Installation Safety Precautions 1. To prevent fire or shock hazards, do not expose this device to rain or moisture. 2. When connecting other products such as DVD players, and personal computers, you should turn off the power of this product and the other devices for protection against electric shocks.
Installation Procedures Unpacking Remove the DVP14 from the shipping box and examine it for any signs of shipping damage or missing items (check with package contents above). All shipping items should be saved if the product is to be moved or returned for service. Shipping unit back to CE labs or dealer for service not in the original box may result in voiding warranty or additional cost.
"Connect" to acquire the latest data from the DVP14. *** NOTE: The Software is the same for the DVP14 & DVP19 *** Instructions for Software Connection 1. Turn on the DVP14. The front panel Display will be blink one time.
Software Operation Main Control Panel State Overall state and format setting: 1. Save and Read: The current layout of the four DVI outputs ports can be saved to a file. In addition, the file can be uploaded in the future to restore the setting.
Page 16
Input Resolution Setting the resolution of the input port. 1. After 10 secongs, the new setting can be applied to the DVP14, but the input source and Display layout mode will return to default. 2. Please reset input source and Display layout mode.
Page 17
Setup Individual Output DVI ports (Channel) There are a total of 4 DVI output ports for theDVP14. Each DVI output can be independently set up to display any area of the input video. Each output can be set to a different output resolution to adapt different combinations of monitors or projectors.
Page 18
This screen representation area will demonstrate the resulting selection of the input video to be displayed for the selected DVI output port. 2
"Original Input Video" shows the resolution information of the input video to each output channel, and it will vary depend- ...
Verify that the sequence of the ports are connected as shown below: (We recommend this sequence, but you can connect the sequence the way it works best for you) One screen will show 1/4 image for the default settings of the DVP14...
Page 20
Using the TV wall Calculator Continued Open the Software DVP14 video wall processor and select the TV Wall Calculator, under the Connect selection: Measure the length and height of the screen as shown below and fill in the boxes in the Calculator (inch) Section, then Select the configuration.
Page 21
Then press: (2) Write setting to device. Repeat this step for Output #3 and Output #4. Output #5, #6, #7, #8 and #9 are for the DVP19 ONLY – Not used on the DVP14...
Page 22
After you press: Write setting to device. From Port #1 to Port #4, you will see the video wall. The margins will be very close. If you are not satisfied, go back to Step #5 to fine-tune the yellow marked data to get a smoother image between screen to screen.
Recommendations No power • Check the AC power cord to ensure proper insertion into the DVP14 and at the wall socket. If using a power strip, verify switch is on and the circuit breaker is not tripped. • If you are recovering from a power outage or...
WARRANTY The SELLER warrants the DVP14 DVI output, Cascadable, Video wall Processor, 4-Display Dual-View to be free from defects in the mate- rial and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should this product fail to be in good...
Page 25
Also, the technical information contained herein regarding the DVP14 fea- tures and specifications is subject to change without further notice.
Page 28
See our full product line at www.celabs.net WARRANTY Cable Electronics, Inc. warrants this product to be free from defects in material and workmanship, under normal use and service, for a period of one year from the purchase by the original purchaser. If this product is defective or malfunctions, Cable Electronics will replace or repair this unit (at their option) within a reasonable time.