Nb-Anl/Off; Rf.gain.control; Program.memory.channels - Cobra 29 LX LE How To Use Manual

Operation

NB-ANL/OFF

NB-ANL/OFF (Noise Blanker/Automatic
Noise Limiter) Button
(Noise Blanker /
Automatic Noise
Limiter) Button
Note
The RF noise blanker is very
effective in reducing repetitive
noises such as ignition interfer-
ence.
1
. . W hen.switched.to.ANL.the.Automatic.Noise.
Limiter.is.activated..This.helps.reduce.noise.
created.by.the.vehicle's.electronics.
. . W hen.switched.to.NB/ANL.mode.the.RF.Noise.
Blanker.is.also.activated,.providing.increased.
noise.filtration.
. . W hen.switched.to.OFF.mode.all.noise.
filtration.will.be.turned.off.
RF Gain Control
RF Gain Control
The.RF.Gain.is.used.to.optimize.reception.in.
strong.or.weak.signal.areas..
NB/ANL
2 3
1.5
NB/ANL
SWR
ANL
S/RF
S/RF
RF
SWR
CAL
3 5 7 9
1
SIG
SWR/CAL
Note
VOL SQ DYNAMIKE
The RF Gain is used to optimize
reception in weak signal areas.
OFF MIN
Rotate.the.RF.Gain.knob.counterclockwise.to.
1
reduce.gain.in.strong.signal.areas..In.weak..
signal.areas.turn.clockwise.to.increase.gain.
24
NB/ANL
2 3
1.5
NB/ANL CAL
SWR TX
ANL
RX
S/ RF
S/RF
RF
NB/ANL
3 5 7 9
1
SIG +30dB
SWR /CAL
S/RF
VOL SQ DYNAMIKE
SWR/CAL
OFF MIN
OFF
NB/ANL
NB/ANL
S/ RF
SWR/CAL
VOL
CAL
OFF
RX
27.405 MHz
+30dB
NB/ANL
MEM
NB/ANL
SWR
ANL
RF GAIN DELTA TUNE
S/RF
S/RF
RF
SWR
CAL
SIG
SWR/CAL
MIN VOL MAX SQ
OFF
Program Memory Channels
Set.first.channel..Press.and.hold.Scan/MemScan.
button..Memory.icon.will.appear..Select.second.
channel,.press.and.hold.Scan/MemScan.button.
again.until.Memory.icon.appears..Repeat.above.
steps.to.enter.up.to.10.channels.in.memory.
1.5 2 3
NB/ANL CAL
SWR MEM WX !
TX
ANL
RX
S/RF
RF RF GAIN DELTA TUNE
SWR
CAL
3 5 7 9
1
SIG +30dB
VOL SQ DYNAMIKE
MIN MAX
MIN
2 3
1.5
CAL
SWR TX
ANL
RX
S/RF
RF
SWR
CAL
3 5 7 9
1
SIG +30dB
MEM
SQ DYNAMIKE
. . P ressing.the.Scan/Memory Scan.button.
1
CH 9/
SCAN
19
toggles.from.Off.to.Scan All Channels.to.
MIN MIN
MEM SCAN
Memory Channel Only Scan.and.back.to.Off..
ESC
3
1.5 2
CAL
TX
SWR
T BACK
.
RX
CAL
3 5 7 9
1
+30dB
MEM WX !
.
DYNAMIKE OFF RF GAIN
.
. Press.Dim/Escape.button.to.end.Scan.and..
2
. return.to.CB.mode.
MIN MIN
CH 9/
SCAN
19
MEM SCAN
ESC
CH 9/
SCAN
19
MEM SCAN
SWR
T BACK
CAL
ESC
MEM
SWR
RF GAIN DELTA TUNE T BACK
CAL
OFF
MIN MAX OFF
CH 9/
SCAN
19
MEM SCAN
ESC
WX !
SWR
RF GAIN DELTA TUNE T BACK
CAL
MAX OFF
CH 9/
SCAN
19
MEM SCAN
ESC
SWR
DELTA TUNE T BACK
CAL
MAX OFF
Operation
Program Memory
Channels
Note
The radio should be
squelched before scan
features are activated.
Note
Keying the microphone will
stop the scan feature.
Note
If more than 10 channels are
attempted to be programmed,
3 error beeps will be heard and
"Memory Full" will be displayed
for 10 seconds or until any
button is pushed.
Note
To remove a channel from
memory, go to the unwanted
memory channel then press
and hold the scan button until
the MEM icon turns off.
Note
If in WX mode the unit will
scan Weather channels.
25