Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Samsung SSA-R1000V
Summary of Contents for Samsung SSA-R1000V
- Page 1 RFID Reader SSA-R1000V SSA-R1100V...
-
Page 2: User Manual
Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice. -
Page 3: Safety Information
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifi cations or attempted repair.) . When cleaning, do not spray water directly onto parts of the product. Doing so may cause fi re or electric shock. -
Page 4: Important Safety Instructions
safety information FCC Statement Caution : Any changes or modifi cations in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. -
Page 5: Table Of Contents
contents PRODUCT INTRODUCTION Features What’s included At a Glance Cable Color Scheme Cable Selection INSTALLATION AND EXTERNAL Installation Precautions on installation CONNECTION External Connection Basic Operations INITIALIZATION WIEGAND Output OUTPUT FORMAT RS-232 Output TROUBLESHOOTING Troubleshooting PRODUCT SPECIFICATIONS Product Specifi cations EnglisEnglish _ 5... -
Page 6: Features
◆ Reverse Polarity Protection ◆ Weatherproof and Dustproof WHAT’S INCLUDED Check if the following items are included in the product package. What’s included in SSA-R1000V SSA-R1000V 3.5 x 40 screws (x2) Bezel of READER 3mm Hex 3.5 x 25 screws (x2) -
Page 7: At A Glance
AT A GLANCE Front/Rear Displays the system operation status using red and green indicators. Buzzer Piezo buzzer. Connection Cable Used to connect to the power or I/O cable. Fixing Hole Fixing hole for wall-mounting. Tamper Switch A tamper switch to detect falling from the wall. EnglisEnglish _ 7... -
Page 8: Cable Color Scheme
product introduction CABLE COLOR SCHEME Item Cable Color Signal Line Description DC +12V DC +12V supplied Power Black Earth-grounding for power Blue Buzzer Control BUZZER Control Input Port Input Yellow LED Control LED Control Input Port Green Out Wiegand 0 Wiegand Data 0 Output Port Output White... -
Page 9: Installation
6-32 or M3 Screws 3.3” 6-32 or M3 Screws (8.38cm) 1/2”hole 6-32 hole Gang Box Lower Reader Reader Module Module SSA-R1000V SSA-R1000V Bezel Bezel 3mm Hex Wrench 3mm Hex Wrench Wall Mount Electric Gang Box Mount Mullion Mount EnglisEnglish _ 9... - Page 10 installation and external connection PRECAUTIONS ON INSTALLATION If installing on a metal wall If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. Metal Wall Spacer...
-
Page 11: External Connection
EXTERNAL CONNECTION Wiring Diagram SSA-R1000V/SSA-R1100V Buzzer Control In RS-232(TX) Brown Blue LED Control In Yellow CONTROLLER Wiegand Data 0 Out Green RS-232(GND) Black Wiegand Data 1 Out White Tamper Output(COM) Pink Tamper Output(NC) Light yellow Black DC +12V POWER Item Cable Wiring Connect the DC+12V to the red line. -
Page 12: Basic Operations
initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the reader, it will sound a beep before entering Standby with the red indicator turned on . Using the card Present the card to the reader until you hear a beep and the red indicator turns green. When the reader has transferred the card data to the controller, it returns to Standby with the red indicator turned on and waits for reading the next card. - Page 13 output format WIEGAND OUTPUT Timing Diagram Data Type • Bit 1 : Even Parity (bit 2 ~ bit 13) • Bit 2 ~ 9 : Facility Code (000 ~ 255) • Bit 10 ~ 25 : ID Number (00000 ~ 65,535) •...
- Page 14 output format RS-232 OUTPUT Output Waveform Indeterminate Region 8 Data Bits 2 Stop Bits Start Bit Data packet corresponding to ASCII character ‘A’ Data Type Start (0X02H) Data (8 Char) End (0x03H) START(0X02H) DATA (1~8 Char) END (0x03H) Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None...
-
Page 15: Troubleshooting
Check the rated voltage specifi ed in the user manual and the catalog. Ensure that the card must comply with the PSK (125 KHz Proximity ) format provided by Samsung. Cards of 125 kHz purchased from other manufacturers may not be supported. -
Page 16: Product Specifications
PRODUCT SPECIFICATIONS Item SSA-R1000V SSA-R1100V Power / Current DC 12V / Max.120mA Reading Time (Card) 30ms Input Port 2ea : External LED Control, External Buzzer Control Output Port 26bit Wiegand LED Indicator 2 Color LED (Red and Green) - Page 17 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. SAMSUNG TECHWIN EUROPE LTD. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Samsung House, 1000 Hillswood Drive, Hillswood Business Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS www.samsungcctvusa.com TEL : +44-1932-45-5300 FAX : +44-1932-45-5325 www.samsungsecurity.com...