Buffalo BU1715 SERVICE MANUAL 17” LCD Monitor BU1715 THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY.EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OFTHIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS...
Buffalo BU1715 1. Monitor Specifications Driving system TFT Color LCD Panel M170EG01 Size 43.2 cm (17.0") LCD Panel Pixel pitch 0.264mm(H) x 0.264mm(V) Viewable angle 140° (H) 130° (V) Response time 16 ms (typ.) Video R, G, B Analog Interface Separate Sync.
Buffalo BU1715 2. LCD Monitor Description The LCD MONITOR will contain a main board, an inverter/power board, an audio board and a keypad board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
Buffalo BU1715 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences.
Buffalo BU1715 3.3 Adjusting the Picture Steps: 1. Press MENU button to display OSD main menu, Press Left button or Right button may select other main Menu. 2. Press MENU button to adjust items of each main menu. 3. Press Left button or Right button may select item you wish to enter.
Page 8
Buffalo BU1715 Main Menu Item Sub Menu Item Sub Menu Icon Description Auto Auto adjust color Color Temp Recall Color Temperature from EEPROM Color Red Setting Red Gain from Digital-register Green Setting Green Gain from Digital-register Blue Setting Blue Gain from Digital-register...
Buffalo BU1715 4.3 Power Supply Requirement Parameter Description A/C Line voltage range 100 V ~ 240 V 50 ± 3Hz, 60 ± 3Hz A/C Line frequency range 280 volts AC for 10 sec @40℃ Input Voltage transients Current 1.5A max at 100V; 0.8A max at 240 V <...
Page 17
Buffalo BU1715 1) MCU initializes. 2) Is the EEPROM blank? 3) Program the EEPROM by default values. 4) Get the PWM value of brightness from EEPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.
Buffalo BU1715 8.2 Trouble Shooting 8.2.1 Main Board 1.No Screen Appear Measured CN201 pin5/6 = 12 V? Check Correspondent component. Measured CN201 pin 9/10= 5V? Is there any shortage or cold solder? Measured U202 pin 2= 3.3V? Yes, all DC level exist Yes.
Page 39
Buffalo BU1715 2. Panel Power Circuit Check R207 should have response from 0V to 5V Measured X601 waveform is normal? When we switch the power switch from off to on Replace X601 Check Q204, Q203 is broken or CN503 solder abnormal?
Page 40
Buffalo BU1715 4. U401-Data Output Check TSU16AK (U401) Signal output (PIN102-103, Measured X401 waveform is 106-113,118-125,128,1) normal? Is the waveform ok? Replace X401 Check HS/VS input signal are Replace U401 normal? Check relative component 8.2.2 Key Board OSD is unstable or not working...
Page 41
Buffalo BU1715 8.2.3 Power/Inverter Board 1.) No power Check to CN102 pin12 = 12V Check Interface board Check AC line volt 120V or 220V Check the voltage of C905(+) Change F901; check BD901, Q903, and IC901 Check start voltage for the pin3 of IC901...
Page 42
Buffalo BU1715 2.) W / LED, No Backlight Check C201 (+) =12V Check D201/Q209/Q210 Check ON/OFF signal Check Interface board Check U201 pin9=12V voltage of C905(+) Change Q201 or Q202 Check the pin1 of U201 have saw tooth wave Change U201 Check D201 (-), D202 (-) has the output of square wave at short time.
Buffalo BU1715 9. White- Balance, Luminance Adjustment Approximately 2 Hours should be allowed for warm up before proceeding White-Balance adjustment. Before started adjust white balance, please setting the Chroma-7120 MEM. Channel 9 to 9300 K colors; MEM. Channel 10 to 7500 K;...
Page 44
Buffalo BU1715 24. Repeat above procedure (item 5,6,7) until chroma 7120 RGB value meet the tolerance =100±2 c. Adjust sRGB (6500 K) color-temperature 1. Switch the chroma-7120 to RGB-mode (with press “MODE” button) 2. Switch the MEM.channel to Channel 01 (with up or down arrow on chroma 7120) 3.
Buffalo BU1715 11. BOM List T780KA4NJSMCA Location Part NO Description Quantity Unit AUPC780ML AUDIO BOARD CBPC780KA4MC CONVERSION BOARD KEPC780KMN KEY BOARD FOR T780K*NMV PWPC7425A3M2 POWER BOARD 15G5786 1 VRSA BRACKET 15G5908 2 BRACKET 15G6090 7 MAIN FRAME 34G1272 Y 5L...