GE Built-In Dishwasher Installation Instructions Manual
GE Built-In Dishwasher Installation Instructions Manual

GE Built-In Dishwasher Installation Instructions Manual

Built-in dishwasher
Hide thumbs Also See for Built-In Dishwasher:

Advertisement

Available languages

Available languages

GE Appliances and Lighting
Appliances

Installation Instructions

Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com
In Canada call 1.800.561.3344 or www.GEAppliances.ca

BEFORE YOU BEGIN

STOP
Read these instructions completely and
carefully.
IMPORTANT
and ordinances.
Be sure to leave these instructions for the
consumer's and local inspector's use.
– Keep these instructions with your
Owner's Manual for future reference.
Installation of this dishwasher requires basic
mechanical, electrical and plumbing skills. Proper installation
is the responsibility of the installer. Product failure due to
improper installation is not covered under the Warranty.
See warranty information.
more time than replacement installations.
imagination at work
– Observe all governing codes
New installations require
IMPORTANT
be installed to allow for future removal from the enclosure
if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions. While performing
installations described in this booklet, gloves and either
safety glasses or goggles should be worn.
WARNING
or injury to persons, the installer must
ensure that the dishwasher is completely
enclosed at the time of installation.
ADVERTENCIA
Para reducir el riesgo de descarga
eléctrica, incendio o lesiones a personas,
el instalador debe asegurarse de que el
lavaplatos esté completamente cerrado
en el momento de la instalación.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
– The dishwasher MUST
31-30263 05-10 GE

Advertisement

Table of Contents
loading

Summary of Contents for GE Built-In Dishwasher

  • Page 1: Installation Instructions

    GE Appliances and Lighting Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com In Canada call 1.800.561.3344 or www.GEAppliances.ca BEFORE YOU BEGIN IMPORTANT – The dishwasher MUST STOP Read these instructions completely and be installed to allow for future removal from the enclosure carefully.
  • Page 2: Parts Supplied

    Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8”long to secure dishwasher to underside of countertop (in literature package). 2 Wood Screws MATERIALS YOU WILL NEED: Ferrule, compression nut and 90° Elbow (3/8”NPT external thread on one end, opposite end sized to fit water supply) Wire Nuts (3) Thread...
  • Page 3: Prepare Dishwasher Enclosure

    Installation Preparation PREPARE DISHWASHER ENCLOSURE 5/8”To 24” Wide. The opening should beto 35”max. height. no more than 10feet in length for proper drainage. Countertop When 32-1/2" to 35" 24" installed into a corner, Min. Underside of 4" allow 2” min. clearance Countertop Dishwasher between dishwasher and...
  • Page 4: Prepare Electrical Wiring

    Installation Preparation PREPARE ELECTRICAL WIRING WARNING fuse or open circuit breaker before beginning installation. Do not use an 1-1/2" Dia. extension cord or adapter plug with this Hole (Max.) appliance. ADVERTENCIA 3" from ADVERTENCIA PARA SEGURIDAD Cabinet 24" interruptor de circuitos antes de comenzar from Wall la instalación.
  • Page 5: Prepare Hot Water Line

    Installation Instructions BEFORE YOU BEGIN PREPARE HOT WATER LINE Locate and set aside the package containing 2 phillips head counter top mounting screws STOP shaded area shown in Figure F. and 2 additional toekickscrews (located in the literature). electrical cable and Drain hose. Or, Cut an additional 1-1/2”...
  • Page 6: Installation Instruction

    Installation Instruction STEP 2 – ADJUST LEVELING LEGS STEP 4 – INSTALL POWER CORD Skip this step if dishwasher will be direct wired. location and lay it on its back. The power cord and connections must comply with the National Electrical Code, Section 422and/or local codes and ordinances.
  • Page 7: Step 6 - Position Water Line And House Wiring

    Installation Instructions STEP 8 – SLIDE DISHWASHER PARTIALLY STEP 6 – POSITION WATER LINE AND INTO CABINET HOUSE WIRING DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR. floor of the opening to avoid interference with base of dishwasher and components under dishwasher. Side dishwasher into the opening a few inches at a time.
  • Page 8: Step 9 - Position Dishwasher Under Countertop

    Installation Instructions STEP 9 – POSITION DISHWASHER UNDER COUNTERTOP Reposition Dishwasher dishwasher and not pinched or in contact with door by Grasping Both springs or other dishwasher components. Sides With Hands TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs.
  • Page 9 Installation Instructions STEP 11 – SECURE DISHWASHER TO STEP 12 – CONNECT WATER SUPPLY CABINET Connect water supply line to 90° elbow. The dishwasher must be secured to the countertop. with the front face of the cabinet frame. nut. IMPORTANT - Compression Nut Check to be sure the dishwasher is centered in the opening and there is no...
  • Page 10: Step 13 - Connect Drain Line

    Installation Instructions DRAIN LINE INSTALLATION STEP 13 – CONNECT DRAIN LINE using either previously determined method. FOLLOW ALL LOCAL CODES AND ORDINANCES. Method 1- Air gap with waste tee or disposer The drain hose molded end will fit 5/8”,3/4”or 1” diameter connections on the air gap, waste tee or disposer .
  • Page 11: Step 14 - Connect Power Supply

    Installation Instructions STEP 14 – CONNECT POWER SUPPLY STEP 15 – PRE-TEST CHECKLIST Review this list after installing your dishwasher to Skip this step if equipped with power cord. avoid charges for a service call that is not covered by your warranty. Check to be sure Power is OFF.
  • Page 12: Step 16 - Dishwasher Wet Test

    Installation Instructions STEP 16 – DISHWASHER WET TEST Turn on power supply(or plug power cord into outlet, if equipped). Turn on Dishwasher Close the door. There will be a 5 second pause, followed by a 60 second pump-out. Check to be sure that water enters the dishwasher. If water does not enter the dishwasher,check to be sure that water and power are turned on.
  • Page 13: Instructions D'installation

    Appareils ménagers GE Instructions d’installation Lave-vaisselle encastré Si vouz des questions, appelez 800.GE.CARES ou visitez notre site Web : GEAppliances.com Au Canada, appelez le 1.800.561.3344 ou visitez : www.electromenagersge.ca AVANT DE COMMENCER IMPORTANT – Le lave-vaisselle DOIT être installé de...
  • Page 14: Pièces Fournies

    Préparation pour l’installation PIÈCES FOURNIES: Deux vis à bois à tête plate cruciforme numéro 8, Vis spéciales à tête cruciforme de 1,6 cm de long pour bloquer le lave-vaisselle sur le dessous du comptoir (dans la documentation). MATÉRIAUX NÉCESSAIRES Bague, écrou de compression et coude à angle droit ( filetage externe de 3/8 po à...
  • Page 15 Installation Preparation PRÉPARER L’ENCEINTE DU LAVE-VAISSELLE profondeur et de 60 à 61 cm de large. L’ouverture doit avoir une hauteur max de 89 cm. tuyau de vidange ne soit pas plus de 3 m de long pour C e tte portion du assurer une bonne vidange.
  • Page 16: Préparation Pour Le Branchement Électrique

    Préparation pour l’installation - Alimentation électrique PRÉPARATION POUR LE BRANCHEMENT ÉLECTRIQUE AVERTISSEMENT SÉCURITÉ : Enlever le fusible du circuit ou Autre emplacement possible de la déclencher le disjoncteur avant de prise de courant commencer l’installation. Avec cet appareil, ne pas utiliser une rallonge 46 cm ou un adaptateur de prise.
  • Page 17 Préparation pour l’installation - Alimentation d’eau chaude PRÉPARATION DE L’ALIMENTATION D’EAU ATTENTION: CHAUDE Ouvrir la porte fait basculer le lave- Tuyau d’eau chaude vaisselle vers l’avant. Ne pas ouvrir pas la porte avant d’être prêt à installer sol, dans la zone hachurée montrée à la figure F. le lave-vaisselle.
  • Page 18 Installation du lave-vaisselle ÉTAPE 2 – RÉGLAGE DES PIEDS DE MISE À ÉTAPE 4 – INSTALLATION DU CORDON NIVEAU D’ALIMENTATION Sauter cette étape si le lave-vaisselle doit être câblé directement. d’installation et le poser sur son dos. Le cordon d’alimentation et les connexions doivent être conformes au code électrique national, section 422 et(ou) aux réglementations et ordonnances en vigueur.
  • Page 19 Installation du lave-vaisselle ÉTAPE 8 : GLISSER LE LAVE-VAISSELLE À ÉTAPE 6 : MISE EN PLACE DU TUYAU TROIS QUARTS DANS L’OUVERTURE DE D’EAU ET DES FILS DE LA MAISON L’ARMOIRE la base du lave-vaisselle et des divers éléments sous IMPORTANT –...
  • Page 20 Installation du lave-vaisselle ÉTAPE 9 – POSITIONNEMENT DU LAVE-VAISSELLE SOUS LE COMPTOIR pas pincés ni en contact avec les ressorts de la porte ou avec d’autres pièces du lave-vaisselle. CONSEIL: Elle doit être positionnée de manière à ne pas bouchonner et à ne pas N e p a s p o u s s e r co n tre porte.
  • Page 21: Étape 11 - Fixation Du Lave-Vaisselle Au Placard

    Installation du lave-vaisselle ÉTAPE 11 – FIXATION DU LAVE-VAISSELLE ÉTAPE 12 : BRANCHEMENT DE AU PLACARD L’ALIMENTATION D’EAU Le lave-vaisselle doit être bloqué sur le comptoir. Brancher le tuyau d’alimentation d’eau au coude à angle droit. de la cuve s’aligne sur l’avant du cadre du placard. l’extrémité...
  • Page 22: Installation Du Tuyau De Vidange

    Installation du lave-vaisselle ÉTAPE 13 – RACCORDEMENT DU CONDUIT INSTALLATION DU TUYAU DE VIDANGE DE VIDANGE le raccord en té d’égout ou le broyeur à déchets, en utilisant la méthode indiquée précédemment. L’extrémité moulée du tuyau de vidange s’ajuste dans des Méthode nº...
  • Page 23: Étape 14: Branchement De L'alimentation Électrique

    Installation du lave-vaisselle ÉTAPE 14: BRANCHEMENT DE ÉTAPE 15 : LISTE DE VÉRIFICATION AVANT L’ALIMENTATION ÉLECTRIQUE DE FAIRE LES ESSAIS Sauter cette étape si le lave-vaisselle est équipé d’un Examiner cette liste après l’installation du lave-vaisselle cordon d’alimentation. Vérifier que le circuit est hors pour éviter les frais d’intervention qui ne sont pas tension.
  • Page 24 Installation du lave-vaisselle ÉTAPE 16: ESSAI DU LAVE-VAISSELLE AVEC DE L’EAU Mettre le circuit sous tension (ou brancher le cordon d’alimentation dans la prise de courant, si installée). Mettre le lave-vaisselle sous tension Fermer la porte. Il y aura une pause de 5 secondes, suivie d’une vidange de 60 secondes. d’alimentation est ouvert et que le circuit est sous tension.

Table of Contents