Husqvarna 323C Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 323C
  6. Operator's manual

Husqvarna 323C Operator's Manual

Hide thumbs Also See for 323C:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
Operator ' s manual
323C 323L 323LD
323CX 325LX 325LDX
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 323C

Summary of Contents for Husqvarna 323C

  • Page 1 Operator ′ s manual 323C 323L 323LD 323CX 325LX 325LDX Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols Only intended for trimmer heads. WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the Noise emission to the environment instructions before using the machine.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS • Please read the operator’s manual carefully. Symbols ............... • Long-term exposure to noise can result in permanent CONTENTS hearing impairment. So always use approved hearing Contents ..............protection. Note the following before starting: ........ INTRODUCTION WARNING! Under no circumstances may the Dear Customer, ............

  • Page 4: Introduction

    Dear Customer, Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    WHAT IS WHAT? What is what? 1 Trimmer head 14 Air purge 2 Grease filler cap, bevel gear 15 Air filter cover 3 Bevel gear 16 Handle adjustment 4 Cutting attachment guard 17 Locking nut 5 Shaft 18 Support flange 6 Loop handle 19 Drive disc 7 Throttle control...

  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. IMPORTANT! The machine is only designed for trimming grass. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data.

  • Page 7: Machine ' S Safety Equipment

    GENERAL SAFETY PRECAUTIONS Machine ′ s safety equipment Check that the throttle control and throttle lock move freely and that the return springs work properly. This section describes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly.
  • Page 8 GENERAL SAFETY PRECAUTIONS Vibration damping system In countries that have a warm and dry climate there is a significant risk of fire. We therefore fit certain mufflers with a spark arrestor mesh. Check whether the muffler on your machine is fitted with this kind of mesh. Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier.

  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS Cutting equipment WARNING! Bear in mind that: This section describes how to choose and maintain your cutting equipment in order to: Engine exhaust fumes contain carbon • Reduce the risk of blade thrust. monoxide, which can cause carbon monoxide poisoning.

  • Page 10: Assembly

    ASSEMBLY Fitting the loop handle • Align the cut-out in the lower part of the shaft with the coupling locking tab on the upper part of the shaft. Then (323C, 325Cx) lock the sections together. • Tighten the knob. •...

  • Page 11: Fitting A Trimmer Guard And Superauto Ii 1" Trimmer Head

    35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade trimmer head guard as possible. (323C) To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

  • Page 12: Fitting The Trimmer Guard And Trimmer Head

    ASSEMBLY Fitting the trimmer guard and trimmer head (325Cx) • Fit the guard as shown in the diagram. Tighten securely. • Insert the locking pin into the hole to lock the shaft. • Screw the trimmer head onto the shaft. 12 –...

  • Page 13: Fuel Handling

    • In order to prevent unintentional starting of the engine, the • If HUSQVARNA two-stroke oil is not available, you may spark plug cap must always be removed during long-term use another two-stroke oil of good quality that is intended storage, if the machine is not under close supervision and for air cooled engines.

  • Page 14: Fuelling

    FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the WARNING! Taking the following precautions, fuel mixture.

  • Page 15: Check Before Starting

    STARTING AND STOPPING Check before starting • Check that the blade guard is not damaged or cracked. Replace the blade guard if it is exposed to impact or is cracked. WARNING! When the engine is started with the choke in either the choke or start throttle positions the cutting attachment will start to rotate immediately.

  • Page 16: Starting And Stopping

    STARTING AND STOPPING Starting and stopping CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged. Always use gloves. Do not use a machine with damaged spark plug cap.

  • Page 17: Working Techniques

    WORKING TECHNIQUES General working instructions WARNING! Neither the operator of the machine nor anyone else may attempt to remove the cut material while the engine is IMPORTANT! running or the cutting equipment is rotating, as this can result in serious injury. This section takes up the basic safety precautions for working with a trimmer.
  • Page 18 WORKING TECHNIQUES Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 19: Maintenance

    MAINTENANCE Carburettor WARNING! If the idle speed cannot be adjusted so that the cutting attachment Your Husqvarna product has been designed and stops, contact your dealer/service manufactured to specifications that reduce harmful workshop. Do not use the machine until it emissions.

  • Page 20: Muffler

    MAINTENANCE High speed jet H The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust The high speed jet H affects the engine power, speed, gases are hot and can contain sparks, which may cause fire temperature and fuel consumption.

  • Page 21: Spark Plug

    Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 22: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop.

  • Page 23: Technical Data

    TECHNICAL DATA Technical data 323C 323L 323LD Engine Cylinder displacement, cm 24,5 24,5 24,5 Cylinder bore, mm 34,0 34,0 34,0 Stroke, mm Idle speed, rpm 2700 2700 2700 Recommended max. fast idle speed, rpm 11000-11700 11000-11700 10000-10500 Speed of output shaft, rpm...
  • Page 24 1/2 idling and 1/2 max speed. NOTE! The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting attachments for the machine. The table indicates the lowest and highest values. 323C Approved accessories Type Cutting attachment guard, Art.

  • Page 25: Ec-Declaration Of Conformity (Applies To Europe Only)

    SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type examination on behalf of Husqvarna AB. The certificates are numbered: SEC/01/838, 01/164/001 - 323C, SEC/01/839, 01/164/002 - 323L, SEC/01/839, 01/164/002 - 323LD, SEC/98/631, 01/164/001 - 325LX, SEC/99/695, 01/164/001 - 325LDX, SEC/00/741,...
  • Page 26 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
  • Page 28 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 29 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 30 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6" ´®z+H?^¶6:¨ ´®z+H?^¶6:¨...
  • Page 31 Trimmy VII 7,0 m 23" 12 cm 5" ~ 3,5 m 11" ~ 15 cm 6" 15 cm 6"...
  • Page 32 1140316-26 ´®z+H?^¶6:¨ ´®z+H?^¶6:¨ 2004-12-09...

This manual is also suitable for:

323ld323cx325lx325ldx323l

Table of Contents