Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for AEG HD 8760
Summary of Contents for AEG HD 8760
- Page 1 HD 8760 HD 8795 Cooker Hood Operating and Installation Instructions...
-
Page 2: Table Of Contents
Metal grease filter Removing the frontal screens: Removing the metal grease filter Charcoal filter Changing the light bulb Special accessories Technical assistance service Technical Specifications Mounting accessories included Electrical connection Wall mounting Printed on recycled paper AEG - putting words into action... -
Page 3: Safety Warnings
Safety warnings For the user • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • Always cover heating elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. - Page 4 • When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approxi- mately the same as the outlet hole. • National and regional building regulations impose a number of restrictions on using hoods and fuel-burning appliances connected to a chimney, such as coal or oil room-heaters and gas fires, in the same room.
-
Page 5: Description Of The Appliance
• The hood is supplied as an extractor unit and can also be used with a filtering function by fitting one charcoal filter. • You will need an original AEG charcoal filter for this function (Available from your local AEG Service Force Centre). -
Page 6: Control Panel
Control Panel • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. -
Page 7: Switching On The Hood
Switching on the hood - Fig. 3 depress towards the bottom to switch on The control ball is a balancer switch. the hood. Depressing the control ball repeatedly towards the bottom, switches on the hood and you may select the motor level desired, depressing once again the hood switches off. -
Page 8: Maintenance And Care
Maintenance and care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood • Clean the outside of the hood using a damp cloth and a mild deter- gent. • Never use corrosive, abrasive or flammable cleaning products. •... -
Page 9: Removing The Metal Grease Filter
Removing the metal Handle grease filter Pull the handle downards, then extract the filter.Fig. 5. Hand washing Soak grease filter(s) for about one hour in hot water with a Fig. 5 grease-loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. -
Page 10: Charcoal Filter
• The charcoal filter should only be used if you want to use the hood in the recirculation function. • To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). • Cleaning/replacing the charcoal filter Unlike other carbon filters, the LONGLIFE carbon filter can be cleaned and reactivated. -
Page 11: Changing The Light Bulb
Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. -
Page 12: Technical Assistance Service
Service and spare parts for UK In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning: 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area. -
Page 13: Technical Specifications
Technical Specifications HD 8795 HD 8760 Dimensions (in cm): Height x Width x Depth 80 x 89,8 x 33,5 80 x 89,8 x 33,5 Maximum absorbed power: 235 W 235 W Motor absorption: 175 W 175 W Lighting*: 3 x 20W (30°... -
Page 14: Electrical Connection
Electrical connection (not for UK) Safety warnings for the electrician Before connecting the appliance to the power supply, check that the voltage indicated on the rating plate corresponds to the mains power supply available. Appliances fitted with a plug can be connected to any standard power socket within easy access. -
Page 15: Wall Mounting
Wall mounting - Fig. 10-11-12-13 • Place the three rubber strips on the back of the cooker hood. Where necessary mount the two spacers provided on the drill holes for definitive fixing. The spacers are useful when the wall which is to house the cooker hood is not perfectly vertical (for example: where it is partially covered with wall tiles). - Page 16 • Mark the wall with a centre line, this will aid mounting procedure (1), position the template so that the mid line printed on the template matches with the centre line previously marked, the lower side of the template corresponds to the lower side of the hood once mounted (2).
- Page 17 • HD 8795 only: Fix the sides of the cooker hood by fastening the pins (10a) to the sides of the fastening screws (10b). Block the sides sliding the two tabs outwards (11). • Make electrical connection (12), but leave the hood disconnected from the Fig.
- Page 20 USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de http://www.aeg.co.uk © Copyright by AEG LI2BUD ed. 04/04...