Parts List; In Dash-Mounting/Removing Unit; Using Stay/Installing Without Sleeve; Electrical Connections - JVC KD-R200 Instructions & Installation Manual

z
Q
bJ
W
Z
z
8
......
z
o
j!::
5
...J
~
~
C)
CH20lS
®
Washer (05)
eEl
Battery
..
" Not supplied for this unit.
8 mm (3/8") 8 mm (3/8")
!IIIIIIItIWWd
ilillillillltlllllb
~Xamu(j'
,
I
R M·RKSO
Q)
Remote controller
Removing the unit
@
Powercord
~
Flat type screws
-M5
x 8
mm (M5
x 3/8")"
CD
Handles
When installing the unit without using the sleeve
Bracket"
Before removing the unit, release the rear section.
Bracket"
In aToyota carfor example, first remove the car radio and install the unit in its place.
Flat type screws-M5 x 8 mm (M5 x 3/8")"
~
®
Rubber cushion
Parts list for installation and connection
Install the unit at an angle of
less than
30'.
[f~"".
be careful not to damage
the fuse on the rear.
®
Sleeve
Bend the appropriate tabs
to hold the sleeve firmly
in place.
In dash-mounting
@
Mounting bolt-
M4 x 5mm (M4 x
114");
M5 x 12.5 mm (M5 x 1/2")
When using the optional stay
Fire wall
;¥
Stay (option)
~
oaShb~~f~F
~
""",."
. .
:
c
@l
Do the required elearical
connections.
®
lock nut (M5)
®
Control panel
ELEORICAL CONNEOIONS
INSTALLATION
The following illustration shows atypical installation. Ifyou have any questions Or require inlonmation regarding installation kits, consult your lYC car audio dealer or acompany supplying kits.
• Ifyou are not sure how to install this unit correctly, have it installed by aqualified technician. . .
Typical connections
Connecting the external amplifier or subwoofer
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this
unit. The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
Remote lead (blue with white stripe)
To the remote lead of other equipment
or automatic antenna if any
Rear line out Rear ground terminal
Set "110 MODE" to "REAR"
(See
"'eneral settings-PSM.")
You can connect apower amplifier for
rear speakers.
Remote lead
Y-conneetor*l
"' Not supplied for this unit.
"' Before checking the operotion ofthis unitprior to instollotion, this
leod must be connected, otherwise the power connot be turned on.
", Firmlyattach the ground wire to the metollic body or to the chassis
ofthe cor-to the place uncoated with paint (ifcoated with paint,
remove the paint before attoching the wire). Failure to do so may
couse damage to the unit.
"4
Signal cord (not supplied for thisunit)
Set "110 MODE" to "WOOFER"
(See
"'eneral settings-PSM.")
You can also connect asubwoofer to
the REAR LINE OUT terminals.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged•
• BEFORE connecting the speaker leads ofthe powercord to the speakers, check the speaker wiring in yourcar.
1
...........
\.
, - - - - - - ,
Ignition switch
}.~:1
CD To the metallic body
1
orchassis ofthecar
Yellow"'
Blue with white
stripe To the remote lead of other
}----'I'--'---c::=.J@
equipment or automatic antenna
if ...
!t
any (200 mA max.)
Connect only the front speakers ifyour
speaker system is two-speaker system.
White with black stripe
~H
~(+)
Front speaker (left) White
Green with black stripe
~:::
Rear speaker (left) Green
Purple with black stripe
~H ®
~("'l
Rear speaker (right) Purple