Summary of Contents for Zodiak R255VDIR/G
-
Page 1: User Manual
Digital Video Security Systems USER MANUAL Anti-Vandal & Water-Resistant 3D-DNR DAY & NIGHT CAMERA R255VDIR/G R255VDIR/W 3-DNR Camera 3D-DNR DAY & NIGHT COLOR CAMERA... - Page 2 Digital Video Security Systems CAUTION RISK OF ELECTRIC SHOCK CAUTION DO NOT OPEN CAUTION RISK OF ELECTRIC SHOCK CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT OPEN DO NOT REMOVE COVER(OR BACK). CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK NO USER-SERVICEABLE PARTS INSIDE.
- Page 3 Digital Video Security Systems Precautions Do not install the camera in Do not install or use the camera in an Do not install the camera under extreme temperature conditions. environment where the humidity is high. unstable lighting conditions. Only use the camera under conditions Do not install or use the camera in an Severe lighting change or flicker can where temperatures are between...
-
Page 4: Table Of Contents
Digital Video Security Systems Contents Contents About 3D - DNR Specification Installation How to Install Sefety Instructions General Features Menu Set Up Menu Set Up ▶ Lens Set Up ▶ Exposure ▶ Back Light ▶ D-WDR ▶ White Bal. ▶ Day &... -
Page 5: About 3D - Dnr
Digital Video Security Systems About D-WDR/BLC/ 3D DNR GENERAL FEATURES - 1/3” Sony Super HAD CCD - Up-Most High Resolution : 550TV Lines 3D-DNR Color - 550TV Line / B/W - 600TV Lines - Built-In Next Generation 3D DNR with 3D Filter Backlight Compensation - Max. -
Page 6: Specification
DC 12V / 24V AC( Dual Power) x258 GENERAL FEATURES SPECIFICATIONS * 1/3" Sony Super HAD CCD MODEL R255VDIR/G R255VDIR/W * Built-In Next Generaltion 3D DNR with 3D Filter Sensor 1/3" SONY Super HAD CCD Total Pixels NTSC=811(H) * 508(V) / PAL=795(H) * 595(V) -
Page 7: Installation
Digital Video Security Systems Installation x258 True Day & Night (ICR-IR Cut Filter Removable) OSD Control Board 1.LENS 2.EXPOSURE 3.WHITE BAL 4.DAY NIGHT COLOR 5.3DNR 6.SPECIAL 7.ADJUST 8.RESET SETTINGS 9.EXIT Settings can be made using the OSD button located on the bottom of the camera. SET UP MENU DEFAULT SET MENU... -
Page 8: How To Install
Digital Video Security Systems How To Install x258 Power (+) Video Signal Power (-) Video GND Power jack Video Jack True Day & Night Cable Connection (ICR-IR Cut Filter Removable) * Camera Adjustment ① Connect Video & Power Line (DC 12V/ AC 24V Regulated Power) ②... -
Page 9: Safety Instructions
Digital Video Security Systems Safety Instructions Precautions for use Please read this manual thoroughly before using the camera to become familiar with the correct operational procedures. Cautions When Using ☞ Do not open the camera body and touch any electrical parts to avoid possible electric shocks. ☞... -
Page 10: General Features
Compensation 3D-DNR Digital Video Security Systems Horizontal Resolution Digital 3D-DNR General Features Noise Reduction Backlight Compensation 3D-DNR Horizontal Resolution D-WDR (Digital Wide Dynamic Range) Digital Digital Noise Wide Dynamic Range Reduction 3D-DNR ☞ The DWDR range of camera use very advanced D-WDR technology, which gives clear images even where the scene is strongly backlit. -
Page 11: Menu Set Up
Digital Video Security Systems Menu Set-Up SET UP MENU DEFAULT SET MENU LENS DC : LEVEL (0 ~100 Adjustable) SHUTTER : FLK/ 1/60 / 1/250, 1/500, 1/2000, 1/5000, 1/10000, 1/100000 BRIGHTNESS ----- SHUTTER AGC : OFF / LOW / MIDDLE/ HIGH BRIGHTNESS SENS-UP : x2~ x258 Level Selectable AGC: ---... -
Page 12: Special Menu
Digital Video Security Systems Special Menu SPECIAL MENU DEFAULT SET MENU CAMERA TITLE ON / OFF D - EFFECT FREEZE / MIRROR/ D-ZOOM/ GAMMA/ NEG. IMAGE AREA SELECT : AREA 1 MOTION AREA DISPLAY : ON / OFF LEFT / RIGHT : 0 ~ 100 Level Adjustable WIDTH : 0 ~ 100 Level Adjustable TOP / BOTTOM : 0 ~ 100 Level Adjustable HEIGHT : 0 ~ 100 Level Adjustable... - Page 13 Digital Video Security Systems Menu Set Up Menu items can be selected by using the OSD buttons of the camera 1. Press the Set Up button. * The Set Up menu will be displayed on the monitor. SETUP LENS EXPOSURE WHITE BAL DAY / NIGHT COLOR...
-
Page 14: Lens Set Up
Digital Video Security Systems 3. Changing menu settings using the Left or Right button. * Available values or Status are displayed by pressing the Left or Right buttons. Press the button until desired value / status is displayed. 4. After completing the setting move the arrow indicator to EXIT and press the SET button to EXIT. -
Page 15: Exposure
Digital Video Security Systems NOTE * When DC is selected, the brightness can be adjusted. The brightness control range is 1 ~ 100. Lens BRIGHTNESS RETURN 3. Press the RETURN to return to the SETUP menu. Exposure This function is used to select Automatic or Manual shutter speed control. 1. - Page 16 Digital Video Security Systems EXPOSURE SHUTTER BRIGHTNESS - - - - SENS-UP HIGH AUTO D-WDR RETURN NOTE * To produce better results with FLK, do not use it in conjunction with the WDR mode in the BACKLIGHT menu. * Desired shutter speed can be selected by user 1/60, 1/250, 1/500, 1/2000, 1/5000, 1/0000, 1/100000, FLK .
-
Page 17: Back Light
Digital Video Security Systems * RETURN: Select Return to save the changes in the EXPOSURE menu and retun to the SETUP menu. NOTE * Pressing the SET button in AUTO mode allows adjustment of image brightness by increasing or decreasing the shutter speed (x2 ~x258). * The higher the level, the brighter the image becomes, but it is possible that an after image (ghosting) could appear. - Page 18 Digital Video Security Systems BLC ON BLC OFF 3. Select a mode using the Left and Right buttons then press the SET button. Select BLC to adjust the desired BLC area and GAIN level. * GAIN : Adjust the BLC sensitivity by selecting LOW, MIDDLE or HIGH. * DEFAULT : Press the Default to back to the factory default when input the wrong data .
- Page 19 Digital Video Security Systems * Move the arrow indicator to RETURN and press the Set Up button after complete the BLC area set to return to EXPOSURE menu. 4. Select HSBLC(High Suppress Backlight Compensation) by using the Left and Right buttons then press the Set Up button to set up the desired HSBLC area and GAIN level.
-
Page 20: D-Wdr
Digital Video Security Systems D-WDR(digital WDR) This camera provides intelligent light level control to overcome even strong backlight conditions. 1. Move the allow indicator to D-WDR using the Up or Down button on the EXPOSURE menu screen. 2. Select the desired feature by using the Left or Right button. EXPOSURE SHUTTER 1/60... -
Page 21: White Bal
Digital Video Security Systems White Balance The White Balance function is used to control the “on-screen” colours. 1. Move the allow indicator to WHITE BAL on the SETUP menu screen using the Up and Down button. 2. Select the desired mode by using the Left or Right button. SETUP LENS EXPOSURE... -
Page 22: Day & Night
Digital Video Security Systems Day / Night Picture can be displayed in either colour of black and white. 1. Select DAY / NIGHT using the Up or Down button on the SETUP menu screen. SETUP LENS EXPOSURE WHITE BAL DAY / NIGHT COLOR 3DNR SPECIAL... -
Page 23: 3Dnr
Digital Video Security Systems 3. Select the desired mode and set the values by using the Left or Right button . * DELAY : The range can be adjusted between 0 ~ 63. * S - LEVEL : The start level can be adjusted between 0 ~ 100. * E - LEVEL : The end level can be adjusted between 0 ~ 100. -
Page 24: Special
Digital Video Security Systems Special 1. When the SETUP menu screen is displayed, select SPECIAL using the Up and Down buttons. SETUP LENS EXPOSURE WHITE BAL DAY / NIGHT COLOR 3DNR SPECIAL ADJUST RESET EXIT 2. Select one of the mode using the Up and Down button. SPECIAL 1. - Page 25 Digital Video Security Systems NOTE * When CAMERA TITLE is set to OFF, the CAMERA TITLE is not displayed on the monitor. 3) Press the SETUP button. CAMERA TITLE 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z ▷...
- Page 26 Digital Video Security Systems NOTE * In cases where the wrong Camera ID has been input..Move the cursor to CLR and press SETUP button to erase characters from left to right, and repeat the above steps to input the characters again. 1-5) To select the position where the Camera ID should be displayed on the screen.
-
Page 27: D - Effect
Digital Video Security Systems ③ Select a new position by using the four C A M 1 directional button, Press the SET button to confirm the position. 2) D - EFFECT Move the cursor to D-EFFECT and press the SET button to set the other image functions. SPECIAL 1. - Page 28 Digital Video Security Systems 2 -2) MIRROR : Flip the image horizontally on the screen. D-EFFECT 1. FREEZE 2. MIRROR V-FLIP 3. D-ZOOM 4. GAMMA 0.45 5. NEG. IMAGE 6. RETURN * V-FLIP : Flip the image vertically on the screen. * ROTATE : Flip the horizontal image vertically on the screen.
-
Page 29: Motion
Digital Video Security Systems NOTE * PAN and TILT function should be available when using the digital zoom. 2-4) GAMMA : Desired gamma values can be adjusted between 0.05 ~ 1.00. 2-5) NEG. IMAGE : ON : Activates negative image just like film OFF : Normal image 2-6) RETURN : Move the arrow indicator to RETURN after complete the setup to return to SPECIAL menu. -
Page 30: Privacy
Digital Video Security Systems ⑤ Move the arrow indicator to select the SENSITIVITY to increase or decrease by using the Left / Right button between the level 0 ~ 40. RETURN : Move the arrow indicator to RETURN after complete the setup to return to SPECIAL menu. 4. -
Page 31: Sync
Digital Video Security Systems ③ Move the arrow indicator to WIDTH to make desired width of cells to increase or decrease by using the Left / Right button between the level 0 ~ 100. ④ Move the arrow indicator to HEIGHT to make desired height of cells to increase or decrease by using the Left / Right button between the level 0 ~ 100. -
Page 32: Reset
Digital Video Security Systems 2. Select the desired mode by using Up or Down button.. ADJUST SHARPNESS - - - - - - - -100 BLUE - - - - - - - -100 - - - - - - - -100 RETURN SHARPNESS : Improving image clarity. -
Page 33: Trouble Shooting
Digital Video Security Systems Trouble Shooting PROBLEM POSSIBLE CAUSE ☞Check the power cable, power supply output and video Northing appears on connection between the camera and monitor. the screen. ☞Are the camera lens or the lens glass dirty? Clean the lens / glass with a soft clean cloth. The image on the ☞Adjust the monitor controls, as required. - Page 34 Digital Video Security Systems -MEMO- - 31 - 3D-DNR DAY & NIGHT COLOR CAMERA...
- Page 35 Digital Video Security Systems -MEMO- - 32 - 3D-DNR DAY & NIGHT COLOR CAMERA...
- Page 36 T.S. MICRO TECH INC. 17109 Gale Ave City of Industry, CA 91745, U.S.A. TEL : +626 839 8998...