Related Manuals for Honda QH4000
Summary of Contents for Honda QH4000
- Page 3 Thank you f o r purchasing an HTA attachment f o r your Honda Tractor. The HTA Model QH4000 Front Quick H i t c h makes i t p o s s i b l e t o a t t a c h e i t h e r an HTA 42"...
- Page 4 REPLACE IMMEDIATELY IF DAMAGED ATTACHING INSTRUCTIONS 1. Insert subframe into attachment completely. 2. Lock in place by movin lever forward to "Lock" osition and secure wit linch pin. P.T.O. ui ed with drive line, connect to trac- lock tor%.% in place. equipped with lift assist springs, lift theattach- m n t and attach springs.
- Page 5 ---------- IMPORTANT: Before beginning assembly of t h i s subframe, l e v e l surface, parking brake s u ~ E R A M E - P R E P _ A R A I L o N Loosely a t t a c h r e a r h i t c h p l a t e (fig.1, item 1) t o bottom...
- Page 6 Thread the adjustment f o r k ( f i g . 2 , 5 ) i n t o the end of t h e push arm (fig.2, item 3 ) . Adjust t h e o v e r a l l length of push arm assembly t o 13/16".
- Page 7 Loosely a t t a c h t h e f r o n t support brackets (fig.5, i t e m 1) t o For each bracket, use one lOmm x 1.25 x item 2 ) w i t h lockwasher, 2 5 m m b o l t (fig.5, and two 1 0 m m x 1.25 x 3 0 m m b o l t s ( f i g .
- Page 8 Loosely a t t a c h f r o n t of s u b f r a m e f l a t b a r s ( f i g . 7 , item t o t h e o u t s i d e a t t a c h i n g p l a t e s .
- Page 9 Tighten the 1/2" bolts (fig.9, Refer to the Torque Specification Table on page Secure the rear hitch plate (fig.1, item to the tractor by tightening the bolt (fig.1, item 1/2" then the 1/2" x 1 1/4" bolt (fig. Refer to the Torque Specification Table page If necessary, adjust the lift arm...
- Page 10 I MP O R TA N T r e f l e c t o r s must be i n s t a l l e d on r e a r fender quick h i t c h i s i n s t a l l e d . Attach t h e two s e l f adhesive r e f l e c t o r s t o t h e rear fender...
-
Page 11: Parts Guide
PARTS GUIDE F r o n t s u p p o r t b r a c k e t F r o n t s u p p o r t b r a c k e t A t t a c h i n g p l a t e A t t a c h i n g p l a t e Hex b o l t... - Page 12 PARTS GUIDE b o l t 3 / 8 " n u t 3 / 8 " , U n i - t o r q u e L i f t l e v e r A d j u s t m e n t f o r k P u s h P i n...
-
Page 13: Specification Table
TORQUE SPECIFICATION TABLE G E N E R A L TORQUE SPECIFICATION TABLE USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN NOTE: Thew normal enpioe treme pressure lubricants Grad8 No. 8011 Size Pounds Feet Min. Mar. Millimeten Inch- valuer r e c c i w d from supplier. - Page 14 Your s a t i s f a c t i o n and goodwill are important t o your dealer and warranty d e t a i l s are explained any problems concerning the product department. have s a t i s f a c t i o n , w e suggest you take t h e f o l l o w i n g action: Discuss your problem w i t h a member o f dealership can be q u i c k l y resolved a t t h a t l e v e l .
- Page 16 H / C 3752482 (9307)