Related Manuals for Honeywell ADEMCO VISTA-48A
Summary of Contents for Honeywell ADEMCO VISTA-48A
- Page 1 ADEMCO VISTA-48A ADEMCO VISTA-48E Security Systems User Guide K0750-1EN 11/04 Rev. A...
-
Page 2: Table Of Contents
Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with your security system. Your Honeywell security system is not designed for use with any device that may be attached to your security system's keypad or other communicating bus if Honeywell has not approved such device for use with your security system. -
Page 3: Burglary System Overview
Burglary System Overview Basic Features • Partitions provide three independent areas of protection, with each partition containing a group of Partitions zones that can be armed and disarmed without affecting other zones or users. • Partitioned systems can include a common area, which is an area shared by users of two other partitions (such as a lobby in a building). -
Page 4: Before Arming (Ready [∗] Key)
• If an entry/exit door or interior zone is faulted when the exit delay ends (e.g., exit door left open), the Exit Alarms system sounds an alarm and starts the entry delay timer. • Disarming the system before entry delay ends stops the alarm sound . •... -
Page 5: Basic Arming Modes
Basic Arming Modes • Security code + [3] (STAY) Stay • Causes: three beeps, armed STAY displayed, ARMED indicator lights • Arms perimeter sensors, but interior sensors are left disarmed. • Use when you want to arm the system with persons staying inside (or if you have pets that are moving throughout the premises). -
Page 6: Using The Keyswitch
Using the Keyswitch • Your system may be equipped with a keyswitch for arming and disarming. • To arm in AWAY mode: Turn the key to the right for 1/2 second and release. Keypads beep twice and the red indicator lights or flashes. GREEN •... -
Page 7: Non-Alarm Functions
Non-Alarm Functions Chime Mode Chime mode alerts you to movement within the premises while the system is disarmed. Chime Mode on • Security code + [9] (Chime message appears) • keypads sound three beeps whenever a protected door, window or other specified zone is opened. •... -
Page 8: Follow-Me Feature (Audio Beeps)
Follow-Me Feature (audio beeps) • This feature lets users enter up to three phone numbers (system-wide) that the system will call in the About Follow- Me/Beeps event of an alarm in any partition at the protected premises, thus alerting the user to the alarm. The follow-me feature works as follows: •... -
Page 9: Advanced System Functions
Advanced System Functions (System Master and Master users only) Accessing Other Partitions • Each keypad is assigned to a partition by your installer and is used to perform functions in that Partition Basics partition and display that partition’s system status. •... -
Page 10: Schedules
Schedules • The system provides up to 24 end-user schedules (programmable by master/installer only), which can About Schedules control various types of events. • Each schedule causes a defined event to start and stop (when appropriate) at a specified time. •... -
Page 11: Time And Date Functions
Time and Date Functions • Master Code+[#] + [6] [3], or if programmed, press the designated function key. Viewing the • The system lets you view its time and date setting. Time and Date • The display remains on for about 30 seconds. •... -
Page 12: Security Codes And Authority Levels
Security Codes and Authority Levels You can assign different security codes for use by other users. • Only the System and Partition Masters can assign user codes to users and change user partitions. Rules for • User code programming involves these steps: Assigning Codes 1. -
Page 13: Testing And Maintaining The System
Testing and Maintaining the System Testing the System (to be conducted weekly) Test mode allows each protection point to be checked for proper operation. • The keypad sounds a single beep every 40 seconds as a reminder that the system is in the Test mode. •... -
Page 14: Trouble Conditions
Trouble Conditions "Check" and The word CHECK on the keypad's display, accompanied by a "beeping" at the keypad, indicates a "Battery" Displays trouble condition in the system. To silence the beeping for these conditions, press any key. • "CHECK" and one or more zone numbers indicates that a problem exists with the displayed zone(s) and requires your attention. -
Page 15: Fire Alarm System (If Installed)
Fire Alarm System (If Installed) General Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will sound their alarms and automatically send signals to your system, triggering a loud, interrupted pulsed sound* from the Keypad(s) and any external sounders. -
Page 16: Quick Guide To Basic System Functions
Quick Guide to Basic System Functions FUNCTION PROCEDURE COMMENTS Press READY key. View faulted zones when system not ready. Check Zones Arm System Enter code. Press arming key desired: Arms system in mode selected. (AWAY, STAY, NIGHT-STAY (Internal), MAXIMUM, INSTANT) Quick Arm Press #. -
Page 17: Charts Of Your System's Features
Charts of Your System’s Features System Features Features Comments Exit Delay (seconds) Part. 1: Part. 2: Part. 3: Entry Delay 1 (seconds) Part. 1: Part. 2: Part. 3: Entry Delay 2 (seconds) Part. 1: Part. 2: Part. 3: Night-Stay (internal) Zones Zones: Quick Arm Quick Bypass... -
Page 18: User Setup
User Setup The following chart will help keep track of system users. Copies should be distributed to the partition 1 and partition 2 (if applicable) masters for their records. To program a user attribute: Enter system/partition master code + [8] + user no. + “#” command listed in column heading… †... - Page 19 Schedules: master code + [#] + [6] [4]. Event Device No. AccessGroup Partition Start Stop Repeat Random Time/ Time/ (see list below) for “01” events: for “02” events: for “04-06” events: (1-4) (yes/no) enter 1-8 enter 1, 2, or 3 (see device list below) Events: 00 = remove event...
- Page 20 – NOTES – – 20 –...
- Page 21 – NOTES – – 21 –...
- Page 22 – NOTES – – 22 –...
- Page 23 WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons.
- Page 24 ONE YEAR LIMITED WARRANTY Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials and workmanship for one year from date of original purchase, under normal use and service.