Samsung SAMBLK2200 Overview

®
Samsung Compatible Active Shutter 3D Glasses
Active Shutter 3D Glasses
Overview
Extra3DGlasses.com SAMBLK2200 Active Shutter 3D glasses are intended as a direct
®
replacement for Samsung 3D Enabled television glasses.
The SAMBLK2200 are only compatible with Samsung 3D Enabled televisions. The TV
communicates with the glasses using an infrared transmitter that is included with all Samsung
3D Enabled televisions. The SAMBLK2200 must be used with a Samsung 3D TV to enjoy
3D viewing.
Included Equipment
Following items are included in the package
1， Active 3D Glasses x1
(contain one piece CR2032 battery)
3， Storage Pouch x1
Using your Extra3DGlasses.com 3D glasses
1. Unpack the 3D glasses from the packaging and remove the protective sheet from the lenses.
This is included to protect the lenses during transportation and can be discarded. The included
cloth bag may be used to protect your 3D glasses
2. Locate and remove the insulation sheet from the battery holder . This is put in place to prevent
the battery from discharging. Once this sheet is removed the glasses battery will function and
the glasses will be ready to use.
3. Follow the user guide of your Samsung® 3D Enabled television to properly set up your television
for 3D viewing.
4. Start up your system and turn on 3D mode
5. Press and hold the power button on the glasses to turn them on. The LED power indicator will
blink once to confirm that the glasses are on and the lenses will appear darker .
6. Put on the glasses and verify that the image appears in 3D and that the glasses are on. If not,
recheck the setting and connection of the entire 3D system.
7. To power off the glasses, press and hold the power button. The LED power indicator will blink
three times to indicate that the glasses are turning of f. The lenses will appear brighter .
8. In order to extend the battery life the glasses will also turn of f automatically after 2 minutes
when there is no longer an infrared signal being sent by the television. The LED power indicator
will blink three times to indicate that the glasses are turning of f. The lenses will appear brighter .
Specifications
Liquid Crystal
Shutter lens
Power consumption 2.8 mA
Infrared
Sync method
Power supply One CR2032 Lithium/Manganese dioxide battery – 3V, 220mAh
Battery life
70 hours of continuous function
Working Temperature
Operating
Condition
Storage Temperature
Model :SAMBLK2200
®
®
2， Cleaning Cloth x1
4， User's Guide x1
Extra3DGlasses.com
Refresh rate
200/240Hz
Maximum receiving
20 Feet
distance
Transmittance 38+/-2%
0℃ to 40℃
-10℃ to 75℃
Product Features
®
1. Liquid Crystal Lenses
The high quality LCD lenses will bring you unbelievable 3D effect;
2. IR Signal Receiver
3 Folding . Earpiece
4 Power Button .
Turn ON: Press the button once;
Turn OFF: Hold the button for about 1.5 seconds.
Auto OFF: The glasses will automatically turn off after 2 minutes if there
is no IR SYNC signal.
5 . LED Indicator
Power ON: LED is on for 1.5 seconds;
Power OFF: LED blinks three times;
Low Battery: LED blinks once every 3 seconds.
6
6. CR2032 Battery
7. Battery Holder
Note: Remove the insulation tab over the battery holder before using.
1
Replacing Battery
Your Extra3DGlasses.com 3D glasses are powered by one CR2032 lithium/manganese
dioxide battery located on the right side of the glasses frame.
When the battery life is low, the LED power indicator will flash 3 times. From this point
the battery life will be approximately 2 hours. The LED will blink every 3 seconds contin-
uously to indicate the low battery life. When the battery is almost completely drained the
glasses may not operate correctly and the battery must be replaced.
To change the battery, follow these steps:
2
Step 1
Press the locking tab of
the battery holder in the
direction indicated by the
arrow
Step 2
While pressing the locking
tab, pull out the battery holder
downwards from the glasses
3
3
1 2
4
5
7
3
Step 3
Remove the old battery
and replace it with a new
standard CR2032 3V Lithium/
Manganesebattery. Be sure
to place the battery in the
correct orientation so the
polarity is correct.
2
4
Step 4
Install the battery holder
with the new battery back
to its original position.
4