Picture In Picture (Pip) - Hitachi 57T500 Operating Manual

Your HITACHI Projection TV incorporates Dual Tuner technology designed for improved viewing enjoyment. This Dual Tuner feature
allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. The
Dual Tuner can operate with only one input (ANT A only) or two inputs (ANT A and ANT B).
ANT A input can be viewed as both the main picture and the sub-picture simultaneously. ANT B can only be viewed as a main picture.
To select between main picture and PIP sub-picture tuning, press the SWAP button on the remote. The green highlighted channel
display will move with every press of the SWAP button. When the top channel display is highlighted, channel tuning is for the main
picture. When the lower channel display is highlighted, channel tuning is for the PIP sub-picture.
The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV
program while viewing other programs from the ANT A source or any of the video inputs.
ANT A
P
P Y
R B
INPUT 1
R (MONO)/L
TO
CONVERTER
AUDIO
P P Y/VIDEO
R B
ANT B INPUT 2
R (MONO)/L
AUDIO
R (MONO)/L VIDEO
INPUT 3
AUDIO
TO HI-FI
R (MONO)/L VIDEO
CENTER
INPUT 4
IN
IR
L
BLASTER R VIDEO
MONITOR
L
OUT
AUDIO
R
Models: 57T500
65T500
Audio Video
OUTPUT
VCR
Use above connection to view VCR program as a sub-picture while viewing another program as main picture (ANT A, ANT B, V:1,
V:2, V:3, or V:5). You may also view the VCR program as a main picture while viewing another program as a sub-picture (ANT A,
V:1, V:2, V:3, or V:5).
PIP button
Press the PIP button and a sub-picture will appear in one of the three different modes (POP, PIP and SPLIT), depending on the last
selection of the PIP mode. To change the PIP mode, use the PIP MODE button to cycle through the three different modes.
POP MODE PICTURE-IN-PICTURE
Press the PIP button and a sub-picture appears in one of the three different modes (POP, PIP and SPLIT), depending on the last
selection of the PIP mode. Press the PIP button again to remove the sub-picture from the screen. Use the SWAP button to select
between main and sub-picture tuning control (indicated by green highlighted channel display.) Press the VID1, VID2, VID3, VID4
or VID5 button when sub-picture channel tuning is being controlled, to change between VIDEO: 1, VIDEO: 2, VIDEO: 3, VIDEO:4,
VIDEO:5 and ANT:A sources, (ANT B source cannot be viewed as a sub-picture.)
PIP
NOTES: 1. In POP mode, thumb stick CURSOR
2. Only sound from the main picture can be heard.
PIP MODE PICTURE-IN-PICTURE
This feature is only available with a 1080i input signal (Component and DVI-HDTV).
DVI-HDTV
S-VIDEO
S-VIDEO
IR
BLASTER
S-VIDEO
Models: 57X500
,
PICTURE-IN-PICTURE (PIP)
ANT A
DVI-HDTV
P
P Y
R B
INPUT 1
R (MONO)/L
TO
CONVERTER
AUDIO
P P Y/VIDEO
R B
ANT B INPUT 2
(MONO)/L
R
AUDIO
R (MONO)/L VIDEO S-VIDEO
INPUT 3
AUDIO
TO HI-FI
R (MONO)/L VIDEO
S-VIDEO
CENTER
INPUT 4
IN
R L VIDEO
S-VIDEO
MONITOR
L
OUT
AUDIO
R
65X500
Audio Video
OUTPUT
VCR
Main Picture
PIP
Sub Picture
will move the sub-picture up/down.
PIP MODE
34 34
DVI-HDTV
SELECT
VOL
VID 3
PIP SURF
PIP ACCESS
SWAP
PIP MODE DAY/NIGHT
REC
CH
FREEZE
,