Table of Contents
Advertisement
The Wireless Weather Station with Digital Barometer offers radio-controlled time,
weather forecast, and indoor and outdoor temperature on one easy to read display.
ATOMIC WEATHER STATION:
Outdoor temperature
Channel indicator
Transmitter low
battery indicator
Forecast icon
512-807 Digital Barometer
Wireless Weather Station
Manual
Introduction
Indoor temperature
Time
WWVB
Perpetual
Reception icon
Calendar
1
Temperature
trend indicators
Current pressure
12-hour pressure
history graph
Advertisement
Table of Contents
Related Manuals for La Crosse Technology 512-807
Summary of Contents for La Crosse Technology 512-807
- Page 1 512-807 Digital Barometer Wireless Weather Station Manual Introduction The Wireless Weather Station with Digital Barometer offers radio-controlled time, weather forecast, and indoor and outdoor temperature on one easy to read display. ATOMIC WEATHER STATION: Outdoor temperature Indoor temperature Channel indicator...
- Page 2 FEATURES: Six digit time display Atomic time and date with manual set option Automatically updates for Daylight Saving Time (on/off option) 12-hour or 24-hour selectable time Barometric pressure with 12-hour history graph. Forecast icons: sunny, partly cloudy, cloudy, rainy and stormy. Time Alarm Perpetual calendar.
- Page 3 Once the indoor data is displayed, proceed to the next step. After the batteries are inserted, the Weather station will start receiving outdoor temp data from the transmitter. NOTE: This can take up to 10 minutes. The outdoor temperature should then be displayed on the Weather station. If this does not happen after 10 minutes, remove the batteries from both units and start again from the beginning.
- Page 4 INSTALL BATTERIES IN THE WEATHER STATION: Wall mount hole Function buttons Battery compartment Battery cover Foldout stands Remove the battery cover from the weather station: Insert a finger in the rounded depression at the bottom of the battery cover. Lift up and pull out to remove battery cover. Install two fresh AA alkaline batteries according to the polarity markings.
-
Page 5: Wwvb Radio Controlled Time
WWVB RADIO CONTROLLED TIME The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time signal continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal antenna in the atomic weather station. However, due to the nature of the Earth’s Ionosphere, reception is very limited during daylight hours. - Page 6 FUNCTION BUTTONS Press and Release Functions Hold 3-5 seconds View MAX/MIN temperatures CHANNEL Change channels if multiple transmitters Cancel current sensor SET/ZONE Select Time Zone Time Calendar/Time set ALARM View Alarm Alarm set 1 step advance in program mode Fast advance Alarm on/off 1 step backward in program mode Fast backward...
-
Page 7: Set Time Zone
SET TIME: The Program menu involves several sections controlled by different buttons. Buttons are located at the top and the back of the weather station. Buttons are: SNOOZE, MEM, CH, SET/ZONE, AL, , BARO, UP ARROW, and DOWN ARROW. NOTE: The time cannot be manually set while the weather station is actively searching for a WWVB signal. -
Page 8: Alarm Activation
ALARM MINUTE: The Alarm Minutes will be flashing. Use the PLUS or MINUS button to set the Minutes. Press and release the AL button. ALARM ACTIVATION: Press and release the AL button to show Alarm Time. Press and release the PLUS button to activate or deactivate the Alarm. The Bell icon appears when alarm is activated. - Page 9 BAROMETRIC PRESSURE: Press and hold BARO button and the Elevation (in feet or meters) will flash. Use the UP or the DOWN ARROW button to enter the current elevation in meters or feet. Press BARO to confirm and exit the setting. NOTE: Elevation will automatically show in Feet if when in inHg and show in Meters when in hPa or mb.
-
Page 10: Low Battery
LOW BATTERY: It is recommended to replace the batteries in all units every 12 months to ensure optimum accuracy of these units. A low battery icon will display next to the outdoor temperature when the transmitter batteries are low and next to the indoor temperature then the batteries in the weather station are low. - Page 11 POSITIONING THE OUTDOOR TEMPERATURE SENSOR The remote temperature sensor should be mounted vertically to avoid damage. WALL MOUNT Install one mounting screw (not included) into a wall within transmission range of the weather station, leaving approximately 3/16 of an inch (5mm) extended from the wall.
-
Page 12: Maintenance
MAINTENANCE Do not expose the display to extreme temperatures, vibration or shock. Keep dry. Clean it with a soft damp cloth. Do not use solvents or scouring agents. The product is not a toy. Keep it out of reach of children. The product is not to be used for medical purpose or for public information, but is determined for home use only. -
Page 13: Warranty Information
La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center. La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. - Page 14 LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY.