Related Manuals for Panasonic BM-ET300
Summary of Contents for Panasonic BM-ET300
- Page 1 Iris Camera Setup Manual BM-ET300 Model No. REJECT ACCEPT Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
-
Page 2: Table Of Contents
CONTENTS PREFACE ..................3 FEATURES . -
Page 3: Preface
PREFACE Iris Camera BM-ET300 is used in an access control system. The iris camera, which captures a user's iris image, is available for following uses. • As an enrollment camera for iris image capturing and iris server enrollment To activate iris recognition, it is necessary to capture the iris images of a user and enroll the iris data in the iris server. -
Page 4: Features
, and electric locks* , etc. These devices are independent to BM-ET300. • Supporting a common access control interface Recognition result outputs support Wiegand, which is one of the interfaces commonly used for access control systems. Any access control panel supporting the Wiegand interface can be directly connected to the iris camera. The camera also has a Wiegand input. -
Page 5: Notification About This Document
NOTIFICATION ABOUT THIS DOCUMENT • This document describes setup instructions of Iris Camera BM-ET300. To use this camera for iris recognition, it is neces- sary to do setup after installation. (Refer to BM-ET300 Operating Instructions for the instructions of basic operation and installation.) -
Page 6: Document Convention
Setup PC: PC in which the setup software is installed Setup software: Panasonic BM-ET300 Setup Software User license software: Panasonic User License Software BM-EU30000E Series that is required to enroll iris data You need to purchase the software which supports the total number of users enrolled. -
Page 7: Precautions
When the dirt is hard to remove, use a mild deter- together with other security system or devices including gent and wipe gently. electric locks. Panasonic is NOT RESPONSIBLE FOR ANY CRIME OR • Do not use the product beyond operating TROUBLE CAUSED BY USING THIS UNIT. requirements. - Page 8 • The camera settings are configured by the iris server. The operational setting of this appliance is configured by the optional Administration Software BM-ES300E, which is to be installed in the iris server. Depending on the settings, the voice guidance will not be output or the live indicator will be off at all times.
-
Page 9: Major Operating Controls And Their Functions
While the iris camera is attached to the wall, the rear r Setup cable connector tamper detection switch is pressed and the camera is BM-ET300 Setup Cable (an exclusive cable supplied to in the “normal operation" mode. the administration software) will be connected between this connector and the serial port of the setup PC. - Page 10 Operation mode change: Switch 1 changes the iris camera between the “normal operation” mode and “setup” mode. Before setup, set this switch to OFF. Booting program change: Switch 2 changes the boot- ing program used by the iris camera. When the program installed in the iris camera cannot boot the iris camera, set this switch to ON and supply the power again.
-
Page 11: Setup Procedure
SETUP PROCEDURE ■ Installation of the Setup ● Initial Setup Procedure Software and Setup Procedure You will connect the iris camera and setup PC with the Installation and connections are completed. Note: The power should be turned off. setup cable supplied to the administration software, and carry out the setup using the setup software installed from the CD-ROM into the setup PC. -
Page 12: System Setup
ON (Upper side) After the setting is read into the software, the "Completed." window will appear. When you click on 1 2 3 4 "OK", the "BM-ET300 setup software" window will appear. (Refer to p. 13.) -
Page 13: Setting Parameters Of The Setup Software
Note: Do not change the file extension (Setup data (*.dat)). • Connection (C) COM Port Connection (C): When you click on this item, the "COM port Connection" window appears. You can change the COM port (COM1 or COM2) selected in the "BM-ET300 Login" window. -
Page 14: Setting Parameters
● Setting Parameters Load (L): The iris camera setting is loaded into the setup software. Camera ID: The ID of iris camera is entered in a decimal number. Store (S): The setting is stored into the iris camera. The 1 to 999999999 is available. The ID should be same as setting is activated when the power is supplied to what is set in the administration software. - Page 15 • Wiegand Setting Parameters (common between Output 2 (Rejected Signal): If "Yes" is selected, pulse access control panels and card readers) signal will be output from recognition result output 2 (REJECT) terminal, when recognition is not suc- The parameters of Wiegand interface are set. The setting cessfully completed.
- Page 16 Matsushita Electric Industrial Co., Ltd. Osaka, Japan http://www.panasonic.co.jp/global/ NM0103-2053 3TR001574CAA Printed in Japan 2003 © Matsushita Electric Industrial Co., Ltd. All rights reserved.