Advertisement
Installation
i. Turn
off the circuit
breaker
(s) (30 amp)
or remox e tlle ch):er's
circuit
fuse at the electrical
box.
2. Be sure the ch):er cord
is unplugged
from
tile wall receptacle.
3. Remox e tile power
cord
coxer
located
at the lower
back.
4. Remox e and discard
ground
strap.
Keep
tlle green
ground
screw for step
7.
5. Install
3/4 in. LL recognized
strain
relief
to power
cord
entl_
hole.
Bring
power
cord
through
strain
relief.
6. Comlect
power
cord
as follows:
A. Comlect
the 2 hot lines
to tile outer
screws of
tlle terminal
block
(marked
L1 and L2).
B. Com_ect
tlle neutral
(white)
line
to tile center
of
tile terminal
block
(marked
N).
7. Attach
ground
wire of power
cord
with tile green
ground
screw
(hole
aboxe
strain
relief
bracket).
Tighten
all
terminal
block
screws
(3) completely.
8. Properly
secure
power
cord
to strain
relief.
9. Reinstall
tile co_ er.
_ILWARNING:
NEVER LEAVE THE
COVER OFF OF THE TERMINAL BLOCK,
CONNECTING
DRYER USING 3-WIRE
CONNECTION
IFREQUIRED,
BYLOCAL C ODE,
INSTALL EXTERNAL GROUND
(NOTPROVIDED)
TOGROUNDED
METAL, COLD WATER PIPE, OR
OTHER E STABLISHED
GROUND
DETERMINED
BYA QUALIFIED
ELECTRICIAN.
GREEN
GROUND
GROUND STRAP
SCREW
HOT
WIRE
STRAIN RELIEF
BRACKET
_
3/4", UL
RECOGNIZED
RELIEF
NEUTRAL
HOT
(White)
WIRE
3 #10AWGMINIMUMCOPPER
COVER
CONDUCTORS O R120/240V 30APOWER
SUPPLY CORD KITMARKED FOR USE
WITHDRYERS & PROVIDED W ITHCLOSED
LOOP ORSPADE TERMINALS WITH
UPTURNED E NDS (NOTSUPPLIED).
i. Tm'n off tile circuit
breaker(s)
(30 amp)
or remo_ e tile ch_er's
circuit
fuse at the electrical
box.
2. Be sure
the ch_er
cord
is unplugged
Kom
the wall.
3. Remoxe
the power
cord
coxer
located
at tile lower back.
4. Install
3/4 in. LL
recognized
strain
relief
to power
cord
entl?_ bole.
Bring
power
cord
through
strain
relief.
5. Connect
power
cord
as follows:
A. Com_ect
the 2 hot lines to the outer
screws
of tile
terminal
block
(marked
L1 and L2).
B. Com_ect
the neutral
{white)
line to tile center
of
the terminal
block
{marked
N).
6. Be sure grotmd
strap
is com_ected
to neutral
(center)
terminal
of block
and to green
ground
screw
on cabinet
rear.
Tighten
all terminal
block
screws
(3) completely.
7. Properly
secure
power
cord
to strain
relief.
S. Reinstall
tile co_ er.
A
,AHb_WARNING: NEVER LEAVE THE
COVER OFF OF THE TERMINAL BLOCK.
Instructions
3
EXHAUST
INFORMATION
_WARNING
- IN CANADA AND IN THE UNITED
STATES, THE REQUIRED
EXHAUST DUCT DIAMETER
IS 4 IN (102ram).
DO NOT USE DUCT LONGER
THAN SPECIFIED IN THE EXHAUST LENGTH TABLE.
Lsing
exhaust
longer
than
specified
length
wilh
" Increase
the drying
times
and
tile energy
cost.
, Reduce
the ch)_er life.
, Accumulate
lint, creating
a potential
fire hazard.
The correct
exhaust
installation
is YOUR
RESPONSIBILITY.
Problems
due to incorrect
installation
are not covered
by the warranty.
Remove
and discard
existing
plastic
or metal
foil transition
duct
and replace
with LL listed
transition
duct.
Tlle MAXIML
M ALLOWABLE
duct
length
and number
of
bends
of the exhaust
system
depends
upon
the type of duct,
number
of turns,
the
type of exhaust
hood
(wall cap),
and all
conditions
noted
below.
The maximum
duct length
for rigid
metal
duct is shown
in the table
below.
EXHAUST
LENGTH
RECOMMENDED
MAXIMUM LENGTH
Exhaust
Hood Types
Recommended
Use only for short
run installations
4" DIA.
_
2-1/2"
No. of 90 -0
Rigid
Rigid
Elbows
Metal
Metal
0
90 Feet
60 Feet
1
60 Feet
45 Feet
2
45 Feet
35 Feet
3
35 Feet
25 Feet
4
25 Feet
15 Feet
EXHAUST
SYSTEM
CHECK LIST
HOOD
OR WALL (AP
• Terminate
in a manner
to prevent back drafts o1 entry of birds or
other wildlife.
• Termination
should present
minimal
resistance
to the exhaust
air flow
and should require
little or no maintenance
to prevent
clogging.
• Never install a screen in or over the exhaust duct.This could cause lint build up.
• Wall caps must be installed
at least 12 in. above ground
level or any other
obstruction
with the opening
pointed
down.
SEPARATION
OF TURNS
For best performance,
separate
all turns by at least 4 ft. of straight
duct,
including
distance
between
last ttHn and exhaust
hood.
TURNS
OTHER
THAN 90 °
* Oile tt_in of 45 ° or less may be ignored.
*
TWO45 °
ttH'i1S
should be treated
as one 90 °
ttH'i1.
, Each
ttH'n
over 45 ° should be treated
as one 90 °
ttwn.
SEALING
OF JOINTS
• _Mljoints should be tight to avoid leaks. The male end of each section of
duct must point away flom the dryer.
Do not assemble
the d uctwork with fasteners
that extend into the d t_ct.
They will serve as a collection
point for lint.
Duct joints
can be made air and moisture-tight
by wrapping
the
overlapped
joints with d t_ct rope.
Horizontal
runs should slope down toward the outdoors
_½ inch per foot
INSULATION
Duct work that runs through
an unheated
area or is near air conditioning
should
be insulated
to reduce condensation
and lint build-up.
Advertisement
