Midi Data Format - Yamaha CP4 Stage Data List

(2) RECEIVE FLOW
MIDI>-+-[SW1]--+---------NOTE OFF
| |
| +---------NOTE ON/OFF
| |
| +---------CONTROL CHANGE
| | MODULATION
| | PORTAMENTO TIME
| | DATA ENTRY MSB
| | DATA ENTRY LSB
| | VOLUME
| | PAN
| | EXPRESSION
| | SUSTAIN SWITCH
| | PORTAMENTO SWITCH
| | SOSTENUTO
| | SOFT PEDAL
| | HARMONIC CONTENT
| | EG RELEASE TIME
| | EG ATTACK TIME
| | BRIGHTNESS
| | EG DECAY TIME
| | VIBRATO RATE
| | VIBRATO DEPTH
| | VIBRATO DELAY
| | EFFECT1 DEPTH (REVERB)
| | EFFECT3 DEPTH (CHORUS)
| | DATA ENTRY INC
| | DATA ENTRY DEC
| | ASSIGNABLE CONTROLLER
| | RPN
| | PITCH BEND SENS.
| |
| | FINE TUNING
| |
| | COARSE TUNING
| |
| | RPN RESET
| |
| +--[SW4]--BANK SEL MSB
| | BANK SEL LSB
| |
| +---------CHANNEL MODE MESSAGE
| | ALL SOUND OFF
| | RESET ALL CONTROLLERS
| | ALL NOTE OFF
| | OMNI MODE OFF
| | OMNI MODE ON
| | MONO MODE ON
| | POLY MODE ON
| |
| +--[SW5]--PROGRAM CHANGE
| |
| +---------PITCH BEND CHANGE
|
+--[SW2]-----------SYSTEM REALTIME MESSAGE
| TIMING CLOCK
|
+------------------ACTIVE SENSING
|
+--[SW3]-+---------SYSTEM EXCLUSIVE MESSAGE
| |
| +---------<BULK DUMP>
| | F0H 43H 0nH 7FH mmH bhH blH ahH amH alH ddH....ddH ccH F7H
| | mm = CP4 STAGE: 1A, CP40 STAGE: 1B
| |
| +---------<PARAMETER CHANGE>
| | F0H 43H 1nH 7FH mmH ahH amH alH ddH.....ddH F7H
| | mm = CP4 STAGE: 1A, CP40 STAGE: 1B
| |
| +---------<BULK DUMP REQUEST>
| | F0H 43H 2nH 7FH mmH ahH amH alH F7H
| | mm = CP4 STAGE: 1A, CP40 STAGE: 1B
| |
| +---------<PARAMETER REQUEST>
| F0H 43H 3nH 7FH mmH ahH amH alH F7H
| mm = CP4 STAGE: 1A, CP40 STAGE: 1B
|
+------------------SYSTEM EXCLUSIVE MESSAGE
IDENTITY REQUEST
[SW1] Complies with Part Receive Channel and Part Receive Switch.
The Program Change of the Performance complies with Basic Channel.
[SW2] MIDI Sync (can be set whether metronome playback or tempo-dependent effect parameters uses the internal
Timing Clock, or external Timing Clock messages received via MIN IN.)
[SW3] MIDI Device Number
[SW4] SYSTEM Transmit/Receive Bank Select
[SW5] SYSTEM Transmit/Receive Program Change
8nH
9nH
BnH, 01H
BnH, 05H
BnH, 06H
BnH, 26H
BnH, 07H
BnH, 0AH
BnH, 0BH
BnH, 40H
BnH, 41H
BnH, 42H
BnH, 43H
BnH, 47H
BnH, 48H
BnH, 49H
BnH, 4AH
BnH, 4BH
BnH, 4CH
BnH, 4DH
BnH, 4EH
BnH, 5BH
BnH, 5DH
BnH, 60H
BnH, 61H
BnH, (01H .. 5FH)
BnH, 64H, 00H, 65H, 00H, 06H,
mmH
BnH, 64H, 01H, 65H, 00H, 06H,
mmH, 26H, llH
BnH, 64H, 02H, 65H, 00H, 06H,
mmH
BnH, 64H, 7FH, 65H, 7FH
BnH, 00H
BnH, 20H
BnH, 78H
BnH, 79H
BnH, 7BH
BnH, 7CH
BnH, 7DH
BnH, 7EH
BnH, 7FH
CnH
EnH
F8H
FEH
F0H 7EH 0nH 06H 01H F7H
(3) TRANSMIT/RECEIVE DATA
(3-1) CHANNEL VOICE MESSAGES
(3-1-1) NOTE OFF
STATUS 1000nnnn (8nH)
NOTE No. 0kkkkkkk
VELOCITY 0vvvvvvv
Receive only
(3-1-2) NOTE ON/OFF
STATUS 1001nnnn (9nH)
NOTE NUMBER 0kkkkkkk
VELOCITY NOTE ON 0vvvvvvv (v≠0)
NOTE OFF 0vvvvvvv (v=0)
(3-1-3) CONTROL CHANGE
STATUS 1011nnnn (BnH)
CONTROL NUMBER 0ccccccc
CONTROL VALUE 0vvvvvvv
*TRANSMITTED CONTROL NUMBER
c = 0 BANK SEL MSB
c = 32 BANK SEL LSB
c = 1 MODULATION
c = 7 VOLUME
c = 64 SUSTAIN SWITCH
c = 91 EFFECT1 DEPTH (REVERB)
c = 93 EFFECT3 DEPTH (CHORUS)
c = 0..95 ASSIGNABLE CONTROLLERS
* RECEIVED CONTROL NUMBER
c = 0 BANK SEL MSB
c = 32 BANK SEL LSB
c = 1 MODULATION
c = 5 PORTAMENTO TIME
c = 6 DATA ENTRY MSB
c = 38 DATA ENTRY LSB
c = 7 VOLUME
c = 10 PAN
c = 11 EXPRESSION
c = 64 SUSTAIN SWITCH
c = 65 PORTAMENTO SWITCH
c = 66 SOSTENUTO
c = 67 SOFT PEDAL
c = 71 HARMONIC CONTENT
c = 72 EG RELEASE TIME
c = 73 EG ATTACK TIME
c = 74 BRIGHTNESS
c = 75 EG DECAY TIME
c = 76 VIBRATO RATE
c = 77 VIBRATO DEPTH
c = 78 VIBRATO DELAY
c = 91 EFFECT1 DEPTH (REVERB)
c = 93 EFFECT3 DEPTH (CHORUS)
c = 96 DATA ENTRY INC
c = 97 DATA ENTRY DEC
c = 0..95 ASSIGNABLE CONTROLLER
*1 Used only when a value is set using RPN.
*2 Invalid with Drum Voices.
*3 Relation between BANK CHANGE and PROGRAM is as follows:
CATEGORY MSB
Normal Voice Preset 1 63
Preset 2 63
Preset 3 63
Preset 4 63
Preset 5 63
Preset 6 63
Preset 7 63
Preset 8 63
Preset 9 63
Preset 10 63
Preset 11 63
Preset 12 63
Preset 13 63
Preset 14 63
Preset 15 63
Preset 16 63
Drum Voice Preset 63
Performance User 63
*4 The default CONTROL NUMBERs of ASSIGNABLE CONTROLLER are as follows:
FOOT CONTROLLER 1 11
FOOT CONTROLLER 2 4
FOOT SWITCH 88
*5 When Sustain is set to something other than "FC3 (Half On)," operating the foot switch transmits only values of
0 (off) or 127 (on).
*6 For CP4 STAGE only
*7 For CP4 STAGE only
PORTAMENTO TIME sets the time it takes for the pitch to reach the next note played when PORTAMENTO
SWITCH is set to on.
0: shortest time; 127: longest time
PAN position relatively changes according to the preset value for each voice.
EFFECT1 DEPTH controls reverb send level.
EFFECT3 DEPTH controls chorus send level.
HARMONIC CONTENT adjusts the resonance preset for each voice.
Setting a value adds to or subtracts from the center value, 64, since it is an offset parameter.
The larger the value more resonant sound will be produced.
The effective range may be narrower than the range you can designate depending on the selected voice.
The parameters, EG ATTACK TIME, EG DECAY TIME, and EG RELEASE TIME, adjust the envelopes preset for
each voice. Setting these values add to or subtract from the center value, 64, since these are offset parameters.
BRIGHTNESS adjusts the cutoff frequency preset for each voice. Setting a value adds to or subtracts from the
center value, 64, since it is an offset parameter.
The smaller the value the cutoff frequency will be lowered.
The effective range may be narrower than the range you can designate depending on the selected voice.
Bank Select will be actually executed when the Program Change message is received.
Bank Select and Program Change numbers that are not supported by Yamaha will be ignored.

MIDI Data Format

n = 0 - 15 CHANNEL NUMBER
k = 0 (C-2) - 127 (G8)
v: ignored
n = 0 - 15 CHANNEL NUMBER
k = 0 (C-2) - 127 (G8)
n = 0 - 15 CHANNEL NUMBER
; v = 63
; v = 0 - 80
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 63
; v = 0 - 80
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 127
; v = 0 - 63: OFF, 64 - 127: ON
; v = 0 - 63: OFF, 64 - 127: ON
; v = 0 - 63: OFF, 64 - 127: ON
; v = 0: -64 - 64: 0 - 127: +63
; v = 0: -64 - 64: 0 - 127: +63
; v = 0: -64 - 64: 0 - 127: +63
; v = 0: -64 - 64: 0 - 127: +63
; v = 0: -64 - 64: 0 - 127: +63
; v = 0: -64 - 64: 0 - 127: +63
; v = 0: -64 - 64: 0 - 127: +63
; v = 0: -64 - 64: 0 - 127: +63
; v = 0 - 127
; v = 0 - 127
; v = 127
; v = 127
; v = 0 - 127
LSB PROGRAM No.
CP4 STAGE CP40 STAGE
0 0..14 0..14
1 0..14
2 0..14
3 0..14 0..34
4 0..5
5 0..25
6 0..16 0..16
7 0..49 0..31
8 0..22 0..12
9 0..28 0..20
10 0..10 0..6
11 0..45 0..38
12 0..45 0..33
13 0..42 0..30
14 0..56 0..33
15 0..4 0..4
32 0..13 0..13
80 0..127 0..127
CP4 STAGE/CP40 STAGE Data List
*3
*3
*5
*4
*3
*3
*2
*1
*1
*2
*2
*1
*1
*4
*6
*6
*6
*6
*7
35