Advertisement
Available languages
Available languages
KS-AX3201D
2-Subwoofer system (2 amplifiers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Incoming signals from INPUT jacks are emitted through the PRE OUT jacks.
Å
JVC car receiver, etc.
ı Speaker input connector.
Connector lead
Line out (Rear)
or
a White "LEFT (+)"
Subwoofer out
b Black "RECEIVER GND"
*
2
c Gray "RIGHT (+)"
HIGH
PRE OUT
INPUT
INPUT
L
L
/
MONO
R
R
PRE OUT
INPUT
L
L
/
MONO
*
2
R
R
2-Subwoofer system
• Use the speakers with an impedance of 4 Ω to 8 Ω.
Å
JVC car receiver, etc.
ı Speaker input connector.
Line out (Rear)
Connector lead
or
a White "LEFT (+)"
Subwoofer out
b Black "RECEIVER GND"
*
2
c Gray "RIGHT (+)"
HIGH
PRE OUT
INPUT
INPUT
L
L
/
MONO
R
R
5-speaker system plus subwoofer—5.1-channel (3 amplifiers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Be sure to connect the line output from the receiver to the left (L) jack on this unit.
Line out (Front)
Å
JVC car receiver, etc.
Line out (Rear)
Line out
Subwoofer out
(Center)
ı Speaker input connector.
Connector lead
*
*
2
2
a White "LEFT (+)"
HIGH
b Black "RECEIVER GND"
PRE OUT
INPUT
INPUT
L
L
/
MONO
c Gray "RIGHT (+)"
R
R
JVC amplifier, etc.
(Purchased separately)
SPECIFICATIONS
Power Output
• Normal Mode:
60 W RMS × 4 channels at 4 Ω and ≤ 1% THD + N
76 dBA (reference: 1 W into 4 Ω)
Signal-to-Noise Ratio
Power Output
• Normal Mode:
90 W RMS × 4 channels at 2 Ω and ≤ 1% THD + N
• Bridge Mode:
150 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N
Maximum Power Output
800 W (400 W × 2)
Load Impedance
• Normal Mode:
4 Ω (2 Ω to 8 Ω allowance)
4 Ω (4 Ω to 8 Ω allowance)
• Bridge Mode:
Frequency Response
5 Hz to 50,000 Hz ( +0 dB, –3 dB)
Input Sensitivity/Impedance
2 V/21 kΩ (0.3 V to 6 V, variable)
Distortion
Less than 0.04% (at 1 kHz)
Power Requirement
DC 14.4 V (11 V to 16 V allowance)
Grounding system
Negative ground
Dimensions (W×H×D)
340 mm × 53.5 mm × 185 mm
7
(13-
/
16
Mass (approx.)
2.3 kg (5.1 lbs)
Accessories
Speaker input connector 3P × 2
Mounting Screw φ 4 × 20 mm (13/16 in.) × 4
Design and specifications are subject to change without notice.
To
Receiver
= Left (+) lead
= Chassis*
1
= Right (+) lead
Subwoofer
SPEAKER OUTPUT
HIGH
INPUT
SPEAKER OUTPUT
Subwoofer
To
Receiver
= Left (+) lead
= Chassis*
1
= Right (+) lead
Subwoofer
Subwoofer
SPEAKER OUTPUT
*
2
JVC amplifier, etc.
(Purchased separately)
*
2
Front
Speaker
To
Receiver
= Left (+) lead
= Chassis*
1
= Left (+) lead
Center Speaker
SPEAKER OUTPUT
KS-AX3204
1
5
in. × 2-
/
in. × 7-
/
in.)
8
16
CONTROLS
KS-AX3204
CROSSOVER
LPF
HPF
OFF
FRONT
KS-AX3202
INPUT SENS.
CROSSOVER
1
.
0
5
2
3
4
LPF
.
5V
0
2V
Å POWER indicator
The green lamp lights while the unit is turned on.
ı CROSSOVER filter switch
OFF: Normally set to this position. The switch is preset to this position when the unit is
shipped.
LPF: Set to this position when you want to turn on the LPF (Low-Pass Filter) switch. The Low-
Pass Filter transmits frequencies lower than 80 Hz.
HPF: Set to this position when you want to turn on the HPF (High-Pass Filter) switch. The
High-Pass Filter transmits frequencies higher than 150 Hz.
Ç INPUT SENS. (input sensitivity) controller
Set this control according to the line-output level of the center unit connected with this unit.
For the line-output level, refer to the <Specifications> in the instruction manual of the center
unit.
If the line-output level of the center unit is unknown, set it in the following procedure:
1. Turn the Input sensitivity control to "5" (minimum).
2. Play a CD source.
3. Increase the volume of the center unit gradually to the maximum level at which sound is not
distorted.
4. Turn the Input sensitivity control clockwise to a level slightly below the level at which sound
starts to be distorted.
This controller is preset to 5V when the unit is shipped.
Î BASS BOOST controller
Turning this boosts the 45 Hz frequency within the range of 0 dB to +18 dB. Adjust the level
while listening to the sound. This controller is preset to MIN when the unit is shipped.
‰ LPF (Low-Pass Filter) controller
Adjust the cutoff frequency (the Low-Pass Filter transmits frequencies lower than the cutoff
frequency) within the range of 50 Hz to 200 Hz. Adjust the level while listening to the
sound. This controller is preset to 50 Hz when the unit is shipped.
TROUBLESHOOTING
The POWER indicator does not light.
• Change the fuses if the current one is blown.
• Connect the ground lead securely to a metal part of the car.
Rear
• Turn on the equipment connected to this unit.
Speaker
• Confirm the battery voltage (11 V to 16 V).
• Use a relay if your system employs too many amplifiers.
• Leave the unit turned off to cool it down if it heats up abnormally.
No sound is heard.
• Confirm the connections for the power supply (see "POWER SUPPLY" on page 1).
• Connect the RCA pin cords to the INPUT jacks, or the speaker input connector to the HIGH
INPUT terminal.
• Confirm the speaker wirings and the position of the CROSSOVER filter switch (See "SPEAKER
CONNECTIONS" on page 2).
Alternator noise is heard.
Subwoofer
• Keep the leads of the POWER terminals away from the RCA pin cords.
• Keep the RCA pin cords away from other electrical cables in the car.
• Connect the ground lead securely to a metal part of the car.
• Make sure the speaker negative leads do not touch the car chassis.
• Connect a bypass capacitor across the accessory switches (horn, fan, etc....).
Noise is made when you connect the unit to an AM (MW/LW) tuner.
• Move all the leads of this unit away from the antenna (aerial) lead.
KS-AX3202
65 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N
76 dBA (reference: 1 W into 4 Ω)
90 W RMS × 2 channels at 2 Ω and ≤ 1% THD + N
150 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N
400 W
4 Ω (2 Ω to 8 Ω allowance)
4 Ω (4 Ω to 8 Ω allowance)
5 Hz to 50,000 Hz ( +0 dB, –3 dB)
2 V/21 kΩ (0.3 V to 6 V, variable)
Less than 0.04% (at 1 kHz)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
207 mm × 53.5 mm × 185 mm
3
1
5
(8-
/16 in. × 2-
/
in. × 7-
/
in.)
8
16
1.48 kg (3.4 lbs)
Speaker input connector 3P × 1
Mounting Screw φ 4 × 20 mm (13/16 in.) × 4
3
HIGH
HIGH
INPUT
INPUT INPUT SENS. CROSSOVER
INPUT SENS.
INPUT
L
L
/
MONO
/
MONO
1
.
1
.
0
5
0
5
2
2
3
3
4
4
.
.
5V
0
2V
5V
0
2V
R
R
REAR
KS-AX3201D
INPUT SENS.
BASS BOOST
.
0
5
8
1
5
POWER
2
3
3
4
HPF
OFF
.
5V
0
2V
0dB
KS-AX3201D
250 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N
60 dBA (reference: 1 W into 4 Ω)
400 W RMS × 1 channels at 2 Ω and ≤ 1% THD + N
—
800 W
4 Ω (2 Ω to 8 Ω allowance)
—
20 Hz to 200 Hz ( +0 dB, –3 dB)
2 V/40 kΩ (0.3 V to 6 V, variable)
Less than 0.08% (at 100 Hz)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
227 mm × 53.5 mm × 185 mm
15
1
(8-
/
in. × 2-
/
in. × 7-
16
8
1.77 kg (4.0 lbs)
Speaker input connector 3P × 1
Mounting Screw φ 4 × 20 mm (13/16 in.) × 4
POWER
LPF
HPF
OFF
LPF
120
1
2
150
10
0
POWER
70
18dB
50Hz
200Hz
5
/
in.)
16
Advertisement
