Summary of Contents for Kenmore 272.98200.491 Oak
- Page 1 SEWING MACH E CABINET OWNER'S MANUAL Model Number 272.98200..49 ! Oak 272.98201.491 White ASSEMBLY PARTS LIST IMPORTANT: 98200-FC Read instructions before assembling. 98201-FC...
- Page 2 Notice to Customer: TO ORDER REPLACEMEN T PARTS CALL 1-800-366-7278 Before beginning assembly, remove all parts from the PLEASE NOTE: To assure proper handling of replacement carton. Check closely with illustrations below to determine parts please include the following information: that all the parts are included.
-
Page 3: Hardware Included
#6x5/8" Brass Panhead Screws Hardware Included (1) Metal Handle (2) 8/32x3/4" Handle Bolt _!98200 on|y)/_ .O_lJ #8x1/2" Panhead Screws (21) Cams (98200 only) ('_) White Plastic PuI'I_ #5x1/2" Flathead Screws (4) 2 PC. Knobs (98200 Metal) (32) #6x1" Flathead Screws (98201 Ceramic) Allen Key (2) #6x1"... -
Page 4: Cabinet Assembly
Understanding Howthe "ARROW-L0C" CamFastenerWorks. ARROW TOWARDS HOLE IN EDGE 1. Position bolt in 2. Press cam into 3. Insert bolt through 4. To lock, rotate cam pre-drilled hole and pre-drilled hole until pre-drilled hole in until tight, using turn until tight, flush with surface, edge of panel. - Page 5 Step2. Placepartsshownbelowon a flat surfaceand presscaminto pre-drilledholesprovided (as illustratedin FIG.2),Aftercamshavebeeninserted(21total),you maynowattachthe eight (8)drawerrunnersusing (32) #6x1" Flathead Screws (FIG. 2A). After attaching the runners, insert the wood dowels (6) in the Front Assembly, Front Brace and Back Brace, (as shown in FIG. 2B). FiG.
- Page 6 Step 3. Attach Front Brace to Filler Strip on back side of Front using (3) 1-1/2" Screws. Be sure to position Brace as shown, cut-out down. Attach the Handle with (2) 8/32x3/4" Bolts (see note below) for Metal or (2) #6x1" Panhead Screws for White Plastic Handle to the Front, Attach Rubber Bumpers to the Front Brace using (2) #6x5/8"...
- Page 7 Step6. AttachPartitionby guidingthe Connecting Bolts into holesin the BackBrace,Back, and FrontAssembly; a lsoallow Dowels in the FrontAssemblyand BackBrace to enterholesin the Partition(as shownin FIG.6). Step7. AttachCompartment B ackto Partition,aligningCamholeswith Bolts.Panel s houldbeflush attop andbottom,whenalignedwith Bolts,turn Camsto lockedposition.AttachCompartment Bottom to partition,(tapededgeto front)againaligningwith Bolts,turn Camsto lockedposition.Attach RightSideto Compartment Backand Bottom;...
- Page 8 NOTE: The following assemblies should be done with Cabinet upright. Step 9. Attach Hinges to Leaf Supports with (4) #8x5/8" Flathead screws each. FIG. 8 tap Magnet with hammer, (as shown in FIG. 8A)o Attach Bronze Strikes to outside of Left and Right sides with #5xl/2" Flathead Screw as in FiG.
- Page 9 Assembling the Drawer Begin Drawerassemblyby insertingDrawerConnectorsinto the endsof the (4) DrawerBacks. (as shownin FIG.A).PushConnectorsall the way into the DrawerBackuntil the tabs lock into place. " F_'_=_::_"_ rawer ack-E Drawer Side - B Drawer Side - C Drawer Connectors _=__ Drawer Assembly "...
- Page 10 CONGRATULATIONS Your Sewing Cabinet is Now Ready for the Machine 98200-9 Page 9 98201-9...
- Page 11 Installing Sewing Machine in your new Cabinet. It may be helpful to read the directions for operating the mechanism before proceeding with the following steps. See page 11, and FIG. 12, on this page. STEP1. To prevent damage to Cabinet surface, place cushioning material just to the left of cut-out.
- Page 12 Operating the Mechanism in your Cabinet To move from FLATBED POSITION TO To move your machine from FREE-ARM position FREE-ARM position: (See FIG. 13, 14 and 15,) to FLATBED position: (See FIGS. 13, 14 and 15), (1.) Remove INSERT (1.) Lift and tilt machine slightly forward. (2.) Lift and tilt machine slightly backwards.
- Page 13 Wood Parts List Top Assembly (D) Hinge Rail (J) Right (I) Left oo o'er) Top (E) Platform "_ Leaf Supports (A) Right Leaf (B) Left Leaf _(G) °i_Side Panel _F)_(F) artition ght Side Pane oo: y • 9 ./-_ (Q) Front Brace/_ o (K) Front (M) Compartment Back (R) Top Drawer...
-
Page 14: Other Parts List
OTHER PARTS LIST LeafScrew HH) x5/8"FL-ZN-YW (D) Mounting Bolts (E) Zinc Flat (B) Connecting (C) Rubber Washers (F) Wing (G) Round Bolts Bumper Magnet (A) Cam (K) #8xl/2" (L) Knob (M) #8x5/8" (N) #5x1/2" Panhead Screw Ant. Brass FH Flathead Screw (H) Leaf Screw Screw... - Page 15 Other Parts List and Numbers Fief. No, Part No. Part No. Ref. No. Description Description 19ram Cam 000709 002553 Platform Hinge 002892 002733 Leaf Hinge Connecting Bolts 002466 000151 Bracket Right Rubber Bumpers 002890 Bracket Left 000150 Mounting Bolts 000220 000152 Zinc Flat Washers Hinge Left...
- Page 16 API Specialty Furniture (A Division of ARROW PRODUCTS, Inc.) P.O. Box 410, Elkhorn, Wl 53121 1-800-533-7347 09-99 98200-BC 98201-BC...