Related Manuals for Fujitsu fi-434PR
Summary of Contents for Fujitsu fi-434PR
- Page 1 P3PC-E862-01XA fi-434PR Imprinter User's Guide: Option English User's Guide Japanese...
- Page 2 Revision Record Edition Date published Revised contents December 2001 First edition Manual code: P3PC-E862-01XA...
- Page 3 Imprinter User's Guide: Option English...
- Page 4 The Customer shall not use the Product without securing the sufficient safety required for the High Safety Required Use. In addition, Fujitsu (or other affiliate's name) shall not be liable against the Customer and/or any third party for any claims or damages arising in connection with the High Safety Required Use by the Customer of the Product.
- Page 5 Phone: (82-2)3787-5970 Fax: (82-2)3787-6070 Website: http://www.fujitsu.co.kr E-mail: webmaster@fkl.fujitsu.co.kr FUJITSU SYSTEMS BUSINESS (MALAYSIA) SDN, BHD. Fujitsu Plaza 1A, Japan Tandang 204, P.O.Box 636, Jalan Sultan, 46770, Petaling Jaya Selangor Darul Ehsan, Malaysia Phone: (60-3)793-3888 Fax: (60-3)7783-0888 FUJITSU PHILIPPINES, INC 2nd Fl., United Life Building, Pasay Road, Legaspi Village...
-
Page 6: Table Of Contents
Table of Contents ❑ ❑ ❑ ❑ ❑ Introduction ... 5 Conventions ... 5 ❑ ❑ ❑ ❑ ❑ 1. Components of the Imprinter ... 6 ❑ ❑ ❑ ❑ ❑ 2. Installation ... 7 (1) Installing the Imprinter ... 7 (2) Mounting the Clamps ... -
Page 7: Introduction
CAUTION indicates that minor personal injury, loss of data, or damage to the scanner may result if you do not follow a procedure correctly. Official Fujitsu part names are indicated with an initial capital letter, as in the part name “Pick Roller”. NOTICE... -
Page 8: Components Of The Imprinter
1. Components of the Imprinter Table 1.1 shows the imprinter components. Component Imprinter Unit Print Cartridge Operator's Guide Imprinter Cable Clamp (black) Clamp (white) Screw Table 1.1 Imprinter Components Quantity External View... -
Page 9: Installation
2. Installation (1) Installing the Imprinter Install the imprinter as follows: Prepare a Phillips screw driver. Turn off the scanner and disconnect the power cable. (1) While pushing the lower part of the imprinter against the scanner, (2) hang the arms on the ADF unit. Push down the ends of the arms to mount the imprinter on the scanner. Move the imprinter unit to the left and secure it with the two screws included with the imprinter componets. -
Page 10: Mounting The Clamps
(2) Mounting the Clamps and Connecting the Imprinter cable Two types of clamps are used for securing the imprinter cable. Mount the clamps as follows: Note: The imprinter cable should be connected after the clamps have been mounted. Clamps (black) Use these clamps (black) to fix the imprinter cable. -
Page 11: Mounting The Print Cartridge
(3) Mounting the Print Cartridge Mount the print cartridge as follows: Turn off the scanner and disconnect the power cable. Hold and raise the knob of the imprinter cover in the direction of the arrow to open the cover. Insert the print cartridge so that its tab is positioned toward the left as shown in the figure to the right. -
Page 12: Operation Test
(4) Operation Test After installing the imprinter, check if the printing operation can be done by using the Offline Print Test mode of the scanner. ■ Print test mode This mode tests the printing performance of the imprinter. Turn the power on while pressing the [Exit] button on the scanner's operator panel. The scanner enters the imprinter test mode and the LCD displays “Print Test”. -
Page 13: Installing The Firmware And Device Driver
3. Operation (1) Replacing the Print Cartridge Replace the print cartridge as follows: Turn off the scanner and disconnect the power cable. Hold and raise the knob of the imprinter cover in the direction of the arrow to open the cover. Unlock the lever which secures the print cartridge and open the lever upward. -
Page 14: Reset Of The Ink Remain Counter
(2) Reset of the Ink Remain Counter You must reset the ink remain counter whenever you replace the print cartridge. When you install the print cartridge, the ink remain counter will automatically count every character printed and a message “Please a new Ink” is displayed on the operator panel when the remaining ink is running short. If this message appears (during read operation), prepare a new ink cartridge. -
Page 15: Clearing Paper Jam
(3) Clearing Paper Jam If paper jams, clear the jammed paper as follows: Remove all the documents on the stacker except the jamed paper. Open the ADF cover. The imprinter automatically moves as shown in the figure. Remove the jammed paper. If the imprinter unit presses down on the paper, hold the handle part (see the figure below for details) and slightly lift the imprinter unit from the stacker to... -
Page 16: Clearing The Nozzle Surface Of The Print Cartridge
(4) Cleaning the Nozzle Surface of the Print Cartridge Ink or stains stuck to the nozzle surface of the print cartridge or leaving the imprinter unused for a while cause poor printing of characters because of blocked emission holes in the nozzle. If your imprinter has this trouble, clean the nozzle surface of the print cartridge. -
Page 17: Clearing The Imprinter Base
(5) Cleaning the Imprinter Base With increased use of the imprinter, dirt such as ink sticks to the imprinter base, causing dirt on the paper. As part of daily maintenance, clean the imprinter base by following the procedure below: NOTE When cleaning, gently wipe off dust on the imprinter base, especially the dotted area below, with an absorbent item that can remove the ink. - Page 18 As shown in the above figures, press a cloth against the edge and base of the shutter part and wipe out dirt. Check that the dirt is wiped out and gently return the imprinter to its original position. [DAMAGE] Use a cloth that is either dry or dampened with water when you clean the imprinter. Use of the F1 or F2 cleaner may damage the imprinter.
-
Page 19: Precautions
4. Precautions When installing or replacing the print cartridge, be careful not to insert out of position. When printing near the edge of paper, note that printing may go across the edge depending on the setting position of the imprinter. The "... -
Page 20: Error Messages
5. Error Messages When the following error messages are displayed on the operator panel, the imprinter is malfunctioning. Recover the imprinter according to the means following the cause. P r i n t A l a r m Possible causes are as follows: •... -
Page 21: Specifications
6. Specifications Table 1.1 presents the imprinter specifications. Item Printing Method Thermal inkjet printing Printed Characters Alphabet Letters: Numeric Characters: Symbols: Maximum Number of Characters Printed Character Size Height 2.91 mm to width 2.82 mm Character Pitch About 3.53 mm Printing Area The printable area of the backside of document is as follows: T Length of document... -
Page 22: Declarations Of Conformity
Declaration of Conformity... - Page 24 Japanese...
- Page 26 ©...
- Page 44 This manual uses recycled paper.