Download
Share
Print this page
Maytag 336729 Installation Manual
  1. Manuals
  2. Brands
  3. Maytag Manuals
  4. Oven
  5. 336729
  6. Installation manual
Maytag 336729 Installation Manual

Maytag 336729 Installation Manual

Gas built-in oven
Hide thumbs
1
2
3
4
5
6
7

Advertisement

Quick Links

Download this manual
GAS
BUILT-IN OVEN
INSTALLikilbN
GUIDE
TO THF INSTALLER:
Leave
this
guide
with
the oven.
NOTE:
If
outslde
venting
is desired
or required
by local
building
codes,
a vent
kit is available.
Contact
your
nearest
Dealer.
IMPORTANT:
Readlhe
Rules
for Safe
Use in your
Use and Care
Manual
before
using
your
oven.
KEEP
T#IS.
GUIDE
For Future
Reference
.
TOOL LIST
The following
tools are needed to install your new oven.
1.
l/8"
drill bit
2.
Electric or hand drill
3.
Flat bladed screwdriver
4.
No. 1 or No. 2 Phillips screwdriver
5.
Pencil
6.
Ruler and straight edge
7.
Hand saw or sabre saw
8.
Pipe wrench
9.
5/0" wrench and l/2"
wrench or adjustable wrench
10.
l/4"
hex socket drive

Advertisement

loading

Related Manuals for Maytag 336729

Summary of Contents for Maytag 336729

  • Page 1 BUILT-IN OVEN INSTALLikilbN GUIDE TO THF INSTALLER: Leave this guide with the oven. outslde NOTE: venting is desired or required by local building codes, a vent kit is available. Contact your nearest Dealer. IMPORTANT: Readlhe Rules for Safe Use in your Use and Care Manual before...
  • Page 2 LOr,ATION cat) III>! !~~,sce, with 5 solId s~dcs, provided lo complclely rnllsl enclOSe the ICC? c<td part of your bul’l-In oven except for the vent lhlmble on the WI: dc \c,nlcd units. See Figure 1 for all necessary dimensions. A culoul 22”...
  • Page 3 EtECTRICAL CONNECTIONS Check wlfh your&al ulllllles for elecfrlcal codes which apply in your area II lhere are no local codes. Ihe Nalional Eleclrical Code, ANSliNFPA under circumstances 70-1987 must be followed. You can get a copy by writing: remove grounding prong from oven...

  • Page 4: Gas Connections

    GAS CONNECTIONS Never reuse an old connecfor when installino a new oven. Be sure no strain is put on the connecting-line assembly. To<prevent gas leaks, put a pipe joint compound, which resisfs the action of L.P. gas on Ihe male (outside) ihreads only.

  • Page 5: Gas Adjustments

    Step 1 i Adjust Pressure Regularor Locate lhe pressure regulator (see Fig. 5). Unscrew Ihe cap and remove lhe spnn relarner. Frg. 6. Turn Ihe relarner over and pul il back info Ihe cap so L. 8, IS showing on Ihe boHom end 01 the relainer. Replace the cap. FIG.
  • Page 6 Step 2: Aqjust Burner Orifice All ove s are factory adjusled for use wth the natural gas used in most areas. !!!I ut. since Ihe gas in some areas may vary, you should check all r-11 ITIALI. Tl.^ ,^,I ^... :..- ^A:..-.-^^. _..^.
  • Page 7 INNER CONE OF FLAME’ Opening Cover ,~CCE~S ” c1~t~,,-~1 rmnn&on Ll-,lIru. Trim Clip Orhce Cover Oven lgnlrer AIR SHLlTTER SCREW...