Options; End Of Cycle Signal - Whirlpool Cabrio WGD6600VU0 Use & Care Manual

.................................................. The Damp Dry Signal is useful when drying bedsheets/linens in a
Type of Load Time*
(Minutes) mixed load. When the signal goes off, open the door to stop the
................................................. dryer, rearrange the load inside the dryer, close the door and
Olefin, polypropylene, sheer nylon 10 - 20 restart the dryer to finish the drying cycle. Rearranging the load
will aid in the drying process.
*Reset cycle to complete drying, if needed.
When using Air Only
• Check that coverings are securely stitched.
• Shake and fluff pillows by hand periodically during the cycle.
• Dry item completely. Foam rubber pillows are slow to dry.
NOTE: Air Only is not available with Automatic Cycles.
You can customize your cycles by selecting options.
NOTE: The Damp Dry Signal is available only with the Automatic
Cycles.
End of Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
Press END OF CYCLE SIGNAL until the desired volume (Loud,
Soft or Off) is selected.
DRUM LIGHT
WRINKLE S HIELD
DAMPDRY
SIGNAL
((nil)
ENDOFCYCLE
SIGNAL
NOTE: When the WRINKLE SHIELD
TM
setting is selected and the
End of Cycle Signal is on, a tone sounds every 5 minutes until the
clothes are removed, or the WRINKLE SHIELD
TM
setting ends.
OPTION;
Drum Light
On some models, select Drum Light to turn on the light inside the
dryer drum. During a cycle, if Drum Light is selected, the drum
light turns on and will remain on until DRUM LIGHT is pressed
again, the door is opened and closed, or the door is left open for
5 minutes.
When the dryer is not running, the drum light will turn on when
DRUM LIGHT is pressed or the dryer door is opened, and it will
remain on until the dryer door has been open for 5 minutes, the
dryer door is closed or DRUM LIGHT is pressed again.
Press DRUM LIGHT at any time to turn the drum light ON or OFE
WRINKLE SHIELD
TM
Setting
The WRINKLE SHIELD
TM
setting helps keep wrinkles from
forming when you cannot unload the dryer promptly at the end of
a cycle. During this option, the dryer stops tumbling and then
tumbles again for a brief period.
• Press the WRINKLE SHIELD
TM
setting to get up to
120 minutes of heat-free, periodic tumbling at the end of a
cycle.
• Stop the WRINKLE SHIELD
TM
setting at any time by pressing
WRINKLE SHIELD
TM
setting or opening the dryer door.
For the Perm Press/Casual Cycle, the WRINKLE SHIELD
TM
setting is preset to ON. The other Automatic Cycles will retain
the WRINKLE SHIELD
TM
setting. For example, if you select
the WRINKLE SHIELD
TM
setting in the Normal cycle, the
WRINKLE SHIELD
TM
setting will be on the next time you
select the Normal cycle.
NOTE: If you do not select the WRINKLE SHIELD
TM
setting, the
dryer stops after cool down.
Damp Dry Signal
Select the Damp Dry Signal to alert you that your clothes are
approximately 80% dry. This is useful when you want to remove
lightweight items in a mixed load to avoid overdrying or remove
partially dry items that may need ironing.
You can change Automatic and Timed Cycles, Modifiers and
Options anytime before pressing Start.
• Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing Start
1. Press PAUSE/CANCEL twice.
2. Select the desired cycle and options.
3. Press START. The dryer starts at the beginning of the new
cycle.
NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change an Option or Modifier anytime before the
selected Option or Modifier begins.
1. Press PAUSE/CANCEL once.
2. Select the new Option and/or Modifiers.
3. Press START to continue the cycle.
NOTE: If you happen to press PAUSE/CANCEL twice, the
program clears and your dryer shuts down. Restart the selection
process.
Changing the Preset Dryness Level Settings
If all of your loads on all Auto Dry cycles are consistently not as
dry as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your
Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental conditions or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly dryer clothes, approximately 15% more drying time)
and 3 (much dryer clothes, approximately 30% more drying
time).
1. The Dryness Level settings cannot be changed while the
dryer is running.
18