Table of Contents
Advertisement
Pin holes
One conductor
is copper
One conductor
is gray
Speaker wire
............
.....
i
•
Left
speakel
speaker
Speaker terminals
Remove the screws from the two holes on
each side of the TV's base.
Connecting
Speakers
to Your TV
Note:/j'yoI_'t'(" c'omT('( iitz 2 cil?om_ >//?Pcil('t"
to//?P TI" llsit_
2 thP
Az/dio O_/t iclcles, y oI_dot_ ' I Jz_'<,d
toc'omwctthPsp_,clk_,rs.
Go Io
pcl2P 16',ibr more h!/brmcttioJl o_zthe A_/dio ©z_/icwks.
Th_,T_, a T(' two spc'ak_'rspac'M'd with rOUT T\" YOUn_'('cl to attach in
oTder to heaT the sound from yOUTT\;. Locate the two speakeTs, eight
screws, and two sets of speaker
wire. You']] need a Philips screwdriver
to attach the screws. To connect your speakers:
1.
Stand at the back of the TV and hold the speaker
so the speaker
grill faces foTward and the speaker
brackets f:_ce you, as the
graphic to the lefi shows.
2.
The pin on the back side of the speaker
bracket goes into the
middle hole between
the screw holes on the TV. Then attach the
SCTeWS to the two holes at the top of the speakeT and two holes at
the bottom of the speaker. Follow the same instructions
to attach
the other speaker.
.
Take one set of speakeT wire. Notice the conductoTs of the wire
ate diftbrent colors. One conductor
is gray; the other one is
copper. This is important
to remember
when connecting
because
the ends of the conductor
need to go into the same colored
speaker
terminals on the speaker
and the TV.
4.
5.
Locate the speaker terminals
on the speakers and on the TV. The
bottom graphic to the left shows the locations.
The rubber piece on the speaker
wire, cal]e(I a ferrite core,
should be closest to the TV when connected.
StaTting with the
lefi speaker, [)TESS down on the Ted tab of the speaker terminal to
insert the exposed
\\-ire of the copper
conductor,
for example,
into
the teTmina] hole. On the back of the T\;, connect the other end
of the copper conductor
to the first Ted speaker
teTmina] on the
left. Connect the other conductor
to the black speaker
terminals,
connecting
on the back of the T\,' to the first black speaker
terminal on the ]eft. Follow the same instructions
to connect the
speakeT \\JR' to the Tight speaker. Make sure the conductors
n_atch
red to red and black to black.
Mounting
Your TV to the Wall
Cautio*n: 77"_e , c#l mo_Jlt mz_s't Ix,tirol mhHm_lm qi fi_'P thm,u
theTY_" J_(,tw(,_ht witho_t ca_si_ 2 d(m_((_(,.
You must first purchas{' a univ{,rsa] \\-a]] mount to mount your T\,' to
the wall Then follow th<'so instructions:
1.
You need to remove the base first in order to attach the \\-all
InOUn[.
A. Place the T\/ facedown
on a surface that is soft, yet strong
enough
to hold the TV'.
B. lJse a Philips SCTewdriver to remove the screws from the two
holes on each side of the TV's base as the arrows indicate in
the graphic to the left.
2.
Make sure all cables are already connected
before attaching the
wall n_ount to the TV.
3.
Folio\\- the diTections indu(led
with the wall mount to mount the
TV to the wall.
ChaSer
l
7
Advertisement
Table of Contents
