Table of Contents
Advertisement
GENERAL
INFORMATION
Never attach an unregulated
gas line to the appliance.
Connection
to an unregulated
gas line can
cause excessive
heat or fire.
Verify the type of gas supply to be used, either Natural Gas (N,G,) or Liquid Propane (L,P.), and make sure the serial plate
agrees with that of the supply, Conversion kits are available separately for an additional cost which will enable you to convert
your grill from L.P, to N,G, or to convert your grill from N.G, to L,P, Please see your local dealer for more information,
NOTE: Always
have a qualified
service technician
perform
difficult conversions
or modifications.
For natural gas installations,
an installer
must supply a gas shutoff valve that is easily accessible
to the grill, All installer
sup-
plied parts must conform to local codes, or in the absence
of local codes, with the National
Electrical
Code, ANSI/NFPA
70-
1990, and the National
Fuel Gas Code, ANSI Z223,1-1998.
All pipe sealants
must be an approved
type and resistant
to the actions of L,P, gases,
Never use pipe sealant on
flare fittings, All gas connections
should be made by a competent
qualified service
technician
and in accordance
with local
codes and ordinances,
In the absence
of local codes, the installation
must comply with the National Fuel Gas Code, ANSI
Z223.1-1998,
Gas conversions
kits may be purchased
separately.
When ordering
gas conversion
kits,
have the model num-
ber, and the type of gas (N,G, or L,P,) used for your grill.
This grill and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing
of that system at test pressures in excess of 1/2 PSIG (3.5 kPa,),
This grill must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure
testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa,),
The installation
of this grill must conform
with local codes, or in the absence of local codes, with National
Fuel Code, ANSI
Z223.1 a- 1998,
Installation in Canada must be in accordance with the Standard Can1-b149.1 and or ,2 (installation code for gas burning appli-
ances and equipment) and local codes.
NATURAL
GAS INSTALLATION
The gas inlet supply pressure should be between 5" and 14" water column,(w.c,) A step down regulator is required
if the line pressure is in excess of 14" w.c, Inlet pressure must not exceed 14" water column (1/2 PSIG)
Check your local gas utility company
or with local codes for instructions
on installing
gas supply lines, Be sure to
check on type and size of run, and how deep to bury the line. If the gas supply line is too small, the grill will not
operate correctly.
Any joint sealant used must be an approved type and be resistant to chemical breakdown resulting from the reaction with N.G,
Attach the natural gas regulator (supplied with your grill) to the brass fitting coming out the bottom, right side of the grill (be
sure the arrow on the regulator is pointing up towards the grill), Attach your gas line to the 3/8" flare fitting coming out of the
natural gas regulator under the grill.
NOTE: The gas line connection
and the gas fitting
must be the same diameter.
Installer supplied shut-off valve (not included) - Place the shut-off valve in an accessible location to enable the gas supply to be cut
off to the unit,
NOTE: A flexible
natural gas line is not included
with Frigidaire
Gallery grills. Natural gas flex line must be purchased
separately
based on the distance
of your grill location from the natural gas line. Please be sure to check the size of
your home's natural gas line fitting to make sure you get the right size connection
for your particular
application.
If
you have questions,
please consult
your local natural gas distributor
or qualified
service
technician.
Advertisement
Table of Contents
