Table of Contents
Advertisement
Other Features
TV Status
Programme Number, Programme Name (or AV), (they are
displayed on the upper left of the screen) and Sleep Timer
(shows the time left on the upper right screen if enabled). In
stereo options the sound indicator is displayed with them too.
They are displayed after programme change for 3 seconds.
Programme Number
Programme Name (5 characters)
These OSD's are displayed when a new programme is en-
tered by digit button, by pressing "P<P" button, or by " " or " "
button, or by "
" button.
TV
Programme Swap (P<P)
This button is used to reenter to the preceding entered pro-
gramme again. Pressing "P<P" consecutively allows to swap
into two last entered programmes.
Double-digit (- -)
This OSD is displayed when the "Double-Digit" button pressed
in place of the programme number indicator.
After that, in order to enter a programme press two digits con-
secutively. Both digits must be entered within 3 seconds or the
function will disappear.
Personal Preferences (PP)
All the preset values will be restored, when pressing "PP".
Sound Indicator
This is a stereo option. The alternatives of the indicator are
Mono, Stereo, Dual I and Dual II. This indicator is displayed
under the programme number indicator on the screen. "I-II"
button is used to select Mono or Stereo, or Dual I or Dual II.
In Mono broadcast or in forced-mono (for stereo broadcast).
In Stereo broadcast.
If dual broadcast detected. Dual I is selected in default and also
can be selected after Dual II by Remote Control.
If Dual II selected by Remote Control.
Picture Mode
The picture mode OSD is displayed below the sound indica-
tor, by TV Status OSD's. According to the WSS data, inside of
the OSD box "4:3", "16:9" or "AUTO" is written.
By pressing "
mode can be switched into 4:3, 16:9 or Auto Mode.
Sleep Timer Last Minute Indicator
It is displayed on the upper right of the screen. If sleep timer is
activated it is displayed with the TV status and erased with it
after 3 seconds.
If there is only one minute of the countdown timer left, it is dis-
played automatically on the upper right side of the screen and
stays there until finished. Then TV goes automatically to stand-
by.
Mute Indicator
It is placed in the upper middle of the screen when enabled,
and it stays there until it is disabled.
To cancel mute, there are two alternative; the first one is press-
ing to " " button, thus volume is set to the preceding value, and
the second one is increasing the volume level, thus it starts at
the minimum level to increase. By decreasing the volume level
in mute state, mute will not be ignored, only the volume level
will decrease. If mute is cancelled after decreasing the volume
level, the volume will return at the decreased level.
No-Signal
No-Signal Timer Indicator
It is displayed in the middle of the screen when no valid sig-
nal detected. It shows the time remaining before switching to
the Stand-By mode (it takes 5 minutes when no signal de-
tected or no any Remote Control command is accessed). The
indicator is displayed for 3 seconds when there is no valid
signal.
After a Remote Control command (if No-Signal Timer is active)
the timer stops and if no signal detected again the timer is ini-
tialized to 5 minutes and starts 3 seconds later to count down.
It is not valid in AV mode.
Blue Background During No-Signal
In case, no valid signal is detected (in TV or AV mode) Blue Back-
ground is activated.During search process Blue Background
is not active. But instead there is another feature given; the
semi-transparent menu background is made blue.
Volume Bar
It is displayed in the lower middle of the screen. When a vol-
ume command is received (pressing "Vol+" or "Vol-" by Re-
mote Control or Front panel) and no menu is active, it stays on
the screen for 3 seconds, after the last volume command or
until another command is received in between.
ENGLISH - 14 -
" button (if Teletext is not active) the picture
Advertisement
Table of Contents
